加速溶剂萃取-在线衍生-气相色谱-质谱法同时分析土壤中有机氯农药和酸性除草剂

建立了土壤中13种极性除草剂与20种非极性有机氯农药的同时萃取检测的方法.利用加速溶剂萃取过程中的温度环境与溶剂环境,使强极性氯代酸性除草剂与五氟苄基溴在萃取池内反应,酯化产物的极性显著降低.利用丙酮溶剂使之与非极性的有机氯农药同时萃取;利用衍生产物与有机氯农药的高电负性使除草剂与有机氯农药在气相色谱负化学源质谱上同时...     

络合萃取-在线衍生土壤酸性除草剂条件选择与优化

以Na4EDTA为络合剂,以五氟苄基溴为衍生试剂,采用快速溶剂萃取仪萃取,同时实现土壤酸性除草剂的络合萃取在线衍生,并以气相色谱-质谱(NCI源)进行检测。对络合条件、衍生条件、萃取条件、离子源选择进行了优化。方法的回收率为75%～95%、相对标准偏差为6.7%～13%、检测限2.8～8.4μg/Kg。     

固相膜萃取-超声洗脱-原位衍生法分析水中不同极性农药残留

建立了水中极性除草剂和非极性杀虫剂固相膜萃取-超声洗脱-原位衍生-气相色谱质谱方法。在样pH≈3时,采用C8固相萃取膜,10 min可完成1000 mL水中两类化合物的萃取;将膜片置于反应瓶中,加入2 mL丙酮溶剂和衍生试剂,对杀虫剂进行超声洗脱、对除草剂进行洗脱衍生。其洗脱、衍生时间为30 min。以HP-5MS(30 m×0.25 mm×0.25μm)为分析柱,采用负化学源技术在10 min内完成两类物质的检测。由于衍生试剂与酸性除草剂是特定的官能团之间的反应,并且衍生时间较短,因此杀虫剂的回收率不受影响。方法实现了不同极性有机物的同时萃取、同时检测。在10~250μg/L线性范围内各组分线性关系良好,相关系数R2>0.9978,检出限<1.0μg/L。不同基质、不同浓度的加标回收率在88%~107%之间;相对标准偏差在3.6%~9.7%之间。     

固相萃取-气相色谱/负化学电离-质谱法测定酸水解植物蛋白及酱油中的3-氯-1,2-丙二醇

建立了酸水解植物蛋白及酱油中3-氯-1,2-丙二醇(3-MCPD)的固相萃取-气相色谱/质谱测定方法。样品经Aoisa-HBL固相萃取柱萃取,正己烷-乙酸乙酯净化提取,七氟丁酰咪唑衍生,衍生物经气相色谱/负化学电离-质谱（GC/NCI-MS）选择离子模式(SIM)检测,外标法定量。3-MCPD的定量检测限为0.5 μg/kg,平均回收率为92.2%～97.4%,相对标准偏差为3.6%～10.9%。该方法检测灵敏度高,定性定量准确。     

顶空固相微萃取原位衍生化气相色谱质谱法测定纺织品中挥发性醛类化合物

采用顶空固相微萃取(SPME)原位衍生化气相色谱/质谱(GC/μ-ECD/MS)法分析了纺织品水萃取溶液的挥发性醛类化合物。实验结果表明,固相萃取纤维上预吸附的衍生化试剂O-(2,3,4,5,6-五氟苄基)羟胺(PFBHA)能与顶空瓶内气体中的醛类化合物反应生成醛肟,在进样口热解吸并经色谱柱分离后,由μ-ECD/MS定性定量检测。该方法不仅能减少试剂消耗,操作简便,而且能克服纺织品水萃取液色素干扰等缺点,提高对产品中醛类有害物质评估准确性。     

络合萃取-在线衍生气相色谱-质谱法检测土壤中酸性除草剂

以Na4-EDTA为络合剂、五氟苄基溴为衍生试剂,对土壤中酸性除草剂进行在线衍生络合萃取,采用负化学源质谱技术对衍生产物实现了快速、高灵敏检测.将10.0 g土壤样品、1.5 mL蒸馏水、0.50 g Na4-EDTA充分混合,加入过量衍生试剂,采用加速溶剂萃取仪,样品在100 ℃,10.3 Mpa压力下,10 min...     

固相萃取/在线衍生化/气质联用技术测定复合食品包装袋中的二氨基甲苯

建立了固相萃取、七氟丁酸酐在线衍生、气相色谱_质谱联用仪(电子轰击电离源)测定二氨基甲苯的方法.实验选择了最佳的衍生化试剂,并对其用量、衍生化时间进行了考察.另外还选择了合适的pH、固相萃取柱填料的用量等.该方法对二氨基甲苯的检测限为0.1μg/L,回收率在80.4%～99.1%之间.     

同步超声衍生萃取土壤中氯代酸性有机物

建立了土壤中酸性有机物的同步衍生萃取分析方法,实现了溶剂体积与土壤质量1:1萃取。将土壤、石英砂、Na4-EDTA和纯水充分混合,室温放置36 h左右使酸性有机物释放,并使水分挥发。将该状态的土壤置于衍生瓶,加入丙酮、五氟苄基溴溶液和K2CO3溶液,利用超声技术将酸性有机物的萃取和衍生同时完成,超声时间为30 min时达到最佳萃取衍生效果。萃取液用硅胶柱净化后,用气相色谱-负化学源质谱(NCI)11 min内完成检测。在5.0~250.0μg/L线性范围内,各组分线性系数r2>0.997,检出限在1.2~4.8μg/kg之间,加标回收率在66.2%~102.9%之间,相对标准偏差在8.4%~13%之间。用该技术对土壤样品分析取得满意结果。     

气相色谱-质谱联用法测定紫菜中扑草净的残留量

建立了固相萃取净化与气相色谱-质谱联用技术测定紫菜中扑草净除草剂残留量的检测方法。样品由乙腈溶剂提取浓缩后,活性炭和氨基柱双柱串联固相萃取净化,由气相色谱-质谱联用技术测定。方法定量限为2μg/kg,满足国外最低10μg/kg的限量要求;方法在10,40和100μg/kg 3个添加水平和不同人员操作条件下,回收率均稳定在90%~120%之间,RSD%≤7.1%。     

气相色谱/负化学源质谱法测定蜂蜜中氯霉素的残留量

建立气相色谱／负化学源质谱(GC／NCIMS)测定蜂蜜中氯霉素残留量的方法。蜂蜜中残留的氯霉素经液-液萃取、固相萃取提取、净化和硅烷化衍生后,进样分析。负化学源质谱采用选择离子模式进行检测,特征离子为m／z=466,468,外标法定量。结果表明,样品中氯霉素浓度为1.0-20μg·kg-1时,工作曲线的线性良好(r=0.9989),回收率为71％-93％,检出限为0.5μg·kg-1。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.