微乳液聚合耦合共混法构建聚偏氟乙烯共混杂化膜

以苯乙烯和甲基丙烯酸甲酯混合物作为油相, 采用反相微乳液法制备了AgCl纳米粒子; 通过微乳液原位聚合油相单体得到包含AgCl纳米粒子的聚合乳液; 将聚合乳液与聚偏氟乙烯(PVDF)通过共混法构建了包含AgCl纳米粒子的PVDF共混杂化膜. 紫外-可见光谱、 透射电子显微镜(TEM)及扫描电子显微镜(SEM)等表征结果和超滤实验结果表明, 聚合乳液加入的同时引入了亲水性聚合物和表面亲水的AgCl纳米粒子, 不仅改善了PVDF共混杂化膜的孔隙率和平均孔径, 还显著增强了PVDF共混杂化膜的极性和亲水性, 最终提升了膜的水通量和抗污染性能; 过量聚合乳液加入后不能与PVDF材料均匀共混, 而且AgCl纳米粒子也会在膜中形成团聚物堵塞膜孔隙, 从而削弱了膜的水通量和抗污染性能.     

反相微乳液模板原位聚合制备纳米氯化银/聚甲基丙烯酸甲酯及其结构表征

用甲基丙烯酸甲酯(MMA)作油相,反相胶束微乳液作为模板,制备了纳米氯化银(AgCl)粒子,再进行原位聚合制备了纳米氯化银/聚甲基丙烯酸甲酯(AgCl/PMMA)复合材料.透射电镜(TEM)分析表明,纳米AgCl的尺寸为20～80 nm.扫描电镜(SEM)测试表明纳米AgCl粒子均匀地存在于PMMA基材中.红外分析证明,胶束中水和表面活性剂AOT的羰基在MMA聚合后微观环境发生变化,纳米粒子同聚合物之间有吸附行为.动态力学(DMTA)分析复合材料,发现纳米AgCl粒子与聚合物之间存在强烈相互作用,形成了中间相层(interphase layer),改变了聚合物的动态力学性能.     

二氧化钛反蛋白石薄膜的制备及其在化学传感器中的应用

用提拉成膜法将单分散295 nm聚甲基丙烯酸甲酯(PMMA)胶体微球自组装成蛋白石光子晶体膜. 在PMMA蛋白石光子晶体膜的空隙里填充15 nm二氧化钛纳米颗粒, 经500 ℃的处理除去PMMA膜板, 制备出大面积, 结构均一的二氧化钛反蛋白石光子晶体膜. 扫描电子显微镜(SEM)观察和X射线光电能谱(XPS)分析表明, 这种二氧化钛反蛋白石光子晶体薄膜是六方紧密堆积. 用这种二氧化钛反蛋白石光子晶体膜对溶液折射率的检测实验表明该传感膜分辨率可达0.01.     

粒子与聚合物协同稳定高内相Pickering乳液

选用二氧化硅纳米粒子(H30)和聚(乳酸-羟基乙酸)共聚物(PLGA)为复合稳定剂, 成功制备出内相体积分数高达90%的高内相Pickering 乳液. 对照实验表明: 单独用H30粒子作稳定剂, 内相体积分数上限为75%; 单独用PLGA 作稳定剂, 发生严重相分离, 不能形成乳液. 无机纳米粒子与聚合物之间的协同作用在制备高内相乳液的过程中起到了关键作用. 因此, 使用无机粒子和聚合物作为混合稳定剂制备高内相乳液是一种新型而有效的方法.     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

聚苯乙烯/Ag核壳结构纳米微粒的制备及表征

用种子乳液聚合法合成了聚苯乙烯（PS）/Ag复合纳米粒子,进一步利用分步聚合技术实现了聚甲基丙烯酸甲酯(PMMA)在微球表面功能化,分别用TEM、XRD、TG-DTA及FT-IR对其结构和形貌进行了表征,并考察了其摩擦学性能.结果表明,在所选择的实验条件下,合成了以Ag纳米微粒为核,PS、PMMA为壳层的核壳结构复合纳米微球,其中Ag纳米核平均粒径约12 nm,复合微球粒径约25 nm,颗粒较均匀并且在有机溶剂中有良好的分散性,作为润滑油添加剂,具有良好的抗磨性能.     

苯乙烯-甲基丙烯酸甲酯悬浮-乳液复合聚合过程中聚合物复合粒子组成的变化

采用苯乙烯(St)悬浮聚合过程中滴加甲基丙烯酸甲酯(MMA)乳液聚合组分,悬浮乳液复合聚合(SECP)方法,制备大粒径聚苯乙烯聚甲基丙烯酸甲酯(PS- PMMA)复合粒子.采用FTIR、1H- NMR、13C- NMR分析方法,研究SECP各个时期复合粒子中MMA- St链节摩尔比,发现悬浮粒子中MMA St链节摩尔比逐渐增大,而PMMA乳胶粒子中逐渐减少,表明悬浮相和乳液相间存在物质传递过程.悬浮粒子中MMA链节质量与MMA总投料质量比主要由乳胶粒子生成速率和乳胶粒子向悬浮粒子凝聚速率决定.最终得到的复合粒子除含PS和PMMA均聚物外,还含少量MMA-St共聚物.     

PMMA纳米球的制备及其银膜包覆技术

采用无皂乳液聚合法制备了单分散、直径为170 nm左右的聚甲基丙烯酸甲酯(PMMA)纳米球, 然后利用3-甲基丙烯酰氧基丙基三甲氧基硅烷(MATS)和3-巯丙基三甲氧基硅烷(MPTMS)对PMMA纳米球进行表面改性, 在其表面包覆一层均匀的巯基, 通过巯基与银离子之间的相互作用, 使银在PMMA纳米球表面成核长大, 从而合成PMMA/Ag纳米球壳粒子. 通过扫描电子显微镜、投射电子显微镜和紫外-可见吸收光谱测试技术对产物性能进行了表征, 研究结果表明, 制备的PMMA/Ag纳米球壳粒子的分散性好、包覆均匀.     

Papain/HA-Phe自组装复合纳米粒子及乳化性能

用L-苯丙氨酸乙酯(L-Phe)改性透明质酸(HA)双亲性生物大分子(HA-Phe)负载生物活性分子木瓜蛋白酶(papain),HA-Phe和Papain通过静电、氢键和疏水相互作用自组装形成生物基Papain/HA-Phe复合纳米粒子.用动态光散射(DLS)和透射电镜(TEM)对复合纳米粒子的尺寸和形貌进行表征.结果显示,形成的复合纳米粒子为球形结构,粒径约308 nm.以此复合纳米粒子为颗粒乳化剂稳定白油,形成水包油型Pickering乳液.乳液的扫描电镜(SEM)显示,复合纳米粒子吸附在油水界面,形成复合纳米粒子的吸附层以稳定乳液.详细研究了pH和盐浓度对复合纳米粒子性质和复合纳米粒子乳化性能的影响.结果表明,随着pH增加,复合纳米粒子在油滴表面的吸附数目减少,乳化性能降低;随着盐浓度增加,复合纳米粒子的形变能力增强,乳化性能提高.进一步研究了乳液中木瓜蛋白酶的活性及美白效果.研究表明,制备的乳液保留了一定的活性,且具有一定的美白效果.     

微波聚合制备单分散、超细聚甲基丙烯酸甲酯微球

在微波辐照下,通过甲基丙烯酸甲酯(MMA)的无乳化剂乳液聚合,制备出粒径单分散、超细聚甲基丙烯酸甲酯(PMMA)微球。微波显著缩短聚合诱导期,加快聚合反应,其部分原因是微波加快引发剂过硫酸钾(KPS)的分解。实验证明微波辐照下KPS的表观分解活化能(ED)由128.3kJ/mol降低到106.0kJ/mol。单体浓度是影响PMMA乳液粒子尺寸的主要因素,在[MMA]小于0.3mol/L时,平均粒径随单体浓度提高而线形增加;[MMA]为0.3～1.0mol/L时,平均粒径稳定在约200nm;之后随单体浓度进一步增加,乳液稳定性变差。引发剂浓度增加对平均粒径影响较小,但增大引发剂浓度可显著降低粒径分散度。选取[MMA]为0.23～0.3mol/L、[KPS]为3×10-3～6×10-3mol/L可以得到粒径200nm的单分散微球。以丙酮/水(体积比1/3)为反应介质,可制备出数均粒径45nm的PMMA纳米粒子。在体系中加入3.5×10-3mol/L的Cu2+,可制备出数均粒径67nm、单分散的PMMA纳米粒子。     

Study of bulk morphology of polymer latex films using laser confocal fluorescence microscopy

Ｐｏｌｙｍｅｒｆｉｌｍｆｏｒｍａｔｉｏｎｆｒｏｍｅｉｔｈｅｒｌａｔｅｘｏｒｓｏｌｕｔｉｏｎｉｓｑｕｉｔｅａｎｉｎｔｅｒｅｓｔｉｎｇｂｕｔｃｏｍｐｌｉｃａｔｅｄｓｕｂｊｅｃｔｄｅａｌｉｎｇｗｉｔｈｄｉｆｆｕｓｉｏｎ,ｉｎｔｅｒｐｅｎｅｔｒａｔｉｏｎａｎｄｃｏａｇｕｌａｔｉｏｎｏｆｐｏｌｙｍｅｒｃｈａｉｎｓ,ａｎｄｅｓｐｅｃｉａｌｌｙｃｏｒｒｅｌａｔｅｄｔｏｔｈｅｐｒｏｐｅｒｔｉｅｓｏｆｔｈｅｆｉｎａｌｌｙｆｏｒｍｅｄｆｉｌｍ.Ｍａｎｙｓｔｕｄｉｅｓ[1—3]ｈａｖｅｂｅｅｎｃａｒｒｉｅｄｏｕｔｏｎｌａｔ…     

Impact modification of thermoplastics by methyl methacrylate and styrene-grafted natural rubber latexes

The preparation and characterization of polymer blends with structured natural rubber (NR)-based latex particles are presented. By a semicontinuous emulsion polymerization process, a natural rubber latex (prevulcanized or not) was coated with a shell of crosslinked polymethylmethacrylate (PMMA) or polystyrene (PS). Furthermore, core–shell latexes based on a natural rubber/crosslinked PS latex semi-interpenetrating network were synthesized in a batch process. These structured particles were incorporated as impact modifiers into a brittle polymer matrix using a Werner & Pfleiderer twin screw extruder. The mechanical properties of PS and PMMA blends with a series of the prepared latexes were investigated. In the case of PMMA blends, relatively simple core (NR)–shell (crosslinked PMMA) particles improved the mechanical properties of PMMA most effectively. An intermediate PS layer between the core and the shell or a natural rubber core with PS subinclusions allowed the E-modulus to be adjusted. The situation was different with the PS blends. Only core–shell particles based on NR-crosslinked PS latex semi-interpenetrating networks could effectively toughen PS. It appears that microdomains in the rubber phase allowed a modification of the crazing behavior. These inclusions were observed inside the NR particles by transmission electron microscopy. Transmission electron photomicrographs of PS and PMMA blends also revealed intact and well-dispersed particles. Scanning electron microscopy of fracture surfaces allowed us to distinguish PS blends reinforced with latex semi-interpenetrating network-based particles from blends with all other types of particles.     

亚微米级聚苯乙烯/聚硅氧烷核壳粒子的制备及其应用

以乳液聚合制备的聚苯乙烯乳液为种子,加入甲基三甲氧基硅烷(MTMS)水解溶液进行缩聚反应,合成亚微米级聚苯乙烯/聚硅氧烷核壳粒子,并以此作为光散射剂添加至聚甲基丙烯酸甲酯(PMMA)树脂中,制备了光散射材料;考察了亚微米级核壳粒子添加在PMMA树脂中的分散性。结果表明:经过双螺杆剪切作用的挤出加工后,可以实现核壳粒子在PMMA树脂中的良好分散。核壳粒子可以大幅度提高PMMA的雾度,当聚苯乙烯/聚硅氧烷核壳粒子(NS82)的含量为1%时,制得的PMMA样片(厚度为2 mm)的雾度为89%,透光率为69%,有效光散射系数为61%。     

Preparation of nonspherical particles via dual-seeded dispersion polymerization in the presence of saturated hydrocarbon droplets

In this study, the effect of various polymerization conditions on the shape of the particles produced by dual-seeded dispersion polymerization of a second monomer with polystyrene (PS) and poly(methyl methacrylate) (PMMA) seed particles in the presence of saturated hydrocarbon droplets in a polar media was discussed. It was observed that with changing the affinity between the hydrocarbon and PS seed particles, second monomer type, polarity, and alcohol type of the medium nonspherical particles with a variety of shapes can be produced. Furthermore, we suggested that the presence of PMMA seed particles in the medium affects the distribution of the second polymer domains on the surface of the PS seed particles in addition to the absorbed amount of the hydrocarbon by PS particles and second polymer domains and the distribution of the hydrocarbon between them. Moreover, the experimental results showed that almond shell-like PS particles can be prepared under certain conditions.     

PS/PMMA mixed polymer brushes on the surface of clay layers: Preparation and application in polymer blends

Polystyrene (PS) and poly(methyl methacrylate) (PMMA) mixed polymer brushes on the surface of clay layers were prepared by using in situ free radical polymerization. Free radical initiator molecules with two quaternary ammonium groups at both ends were intercalated into the interlayer spacing of clay layers. The amount of polymer brushes grafted on the surface of clay layers can be controlled by controlling the polymerization time. Thermogravimetric analysis, X‐ray diffraction, and high‐resolution transmission electron microscope results indicated successful preparation of the mixed polymer brushes on the surface of clay layers. The kinetics of the grafting of the monomers was also studied. The mixed polymer brushes on the surface of clay layers were used as compatibilizers in blends of PS and PMMA. In the blends, the intercalated clay particles tend to locate at the interface of two phases reducing the interfacial tension. In the meanwhile, PMMA homopolymer chains tend to intercalate into clay layers. The driving force for the intercalation is the compatibility between homo‐PMMA chains and PMMA brushes on the surface of clay layers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5329–5338, 2007     

Semi-continuous emulsion polymerization of styrene in the presence of poly(methyl methacrylate) seed particles. Polymerization conditions giving core-shell particles

This work reports the morphology of two-phase latex particles prepared by semi-continuous seed emulsion polymerization of styrene in the presence of polar poly(methyl methacrylate), PMMA, seed particles, using different conditions of non-polar styrene feed rate, rate of initiation, seed particle concentration and temperature of polymerization.The expected latex particle morphology at thermodynamic equilibrium is an inverted core-shell structure where the non-polar polystyrene would form the core. However, depending on the set of process conditions used the morphology of the resulting two-phase particles varied from that of a pure core-shell structure, over intermediate structures in which a shell of PS surrounded a PMMA core containing an increasing number of PS phase domains, to a structure in which the entire PS phase was present as discrete PS phase domain, more or less evenly distributed in a matrix of PMMA.By the use of a caloirimetric reactor system the monomer concentration in the particles during the different polymerization experiments could be calculated by comparing the integral of the polymerization rate curve with the integral of the monomer feed rate. A comparison between particle morphology and the calculated concentration of plasticizing monomer in the polymerizing particles strongly suggested that the diffusivity of the entering oligo radicals determined by the difference between polymerization temperature and the glass transition temperature of the monomer-swollen core polymer is a key factor determining the morphology of two-phase particles prepared by semi-continuous seed emulsion polymerization.Two-phase particles with a true core-shell structure were obtained in experiments where the estimated glass transition temperature of the PMMA phase was only a few degrees below the polymerization temperature. The results show that such particles can be obtained under conditions of high as well as low styrene feed rates, provided that the rate of initiation is properly adjusted.     

The morphology of composite polymer particles produced by multistage soapless seeded emulsion polymerization

 Composite polymer particles which contain poly(methyl methacrylate) (PMMA) and polystyrene (PS) components (PMMA/PS composite particle) were synthesized by the method of multistage soapless seeded emulsion polymerization. In this study, the process of multistage soapless seeded emulsion polymerization included two-stage polymerization, three-stage polymerization or four-stage polymerization. The morphologies of the PMMA/PS composite particles were studied. The kinetic factor was the main force to control the morphology of the linear PMMA–PS composite particles which were synthesized by the method of two-stage reaction. Both the kinetic factor and the thermodynamic factor decide the morphology of the linear composite particles which were synthesized by the method of either three-stage or four-stage reaction. However, the thermodynamic factor cannot influence the morphology of the PMMA/PS composite particles with a cross-linked structure which were synthesized by the method of three-stage reaction. The cross-linked composite polymer particles had the morphology of a multilayer structure, which showed that the polymer layers accumulated in their order of production. Received: 9 January 2001 Accepted: 14 June 2001     

Preparation of hemispherical particles by cleavage of micrometer-sized,spherical poly(methyl methacrylate)/polystyrene composite particle with Janus structure: effect of molecular weight

Micrometer-sized, hemispherical polymer particles were prepared as a result of cleavage of spherical Janus poly(methyl methacrylate) (PMMA)/polystyrene (PS) composite particle by treating particles with acetone/water solutions. The original PMMA/PS composite particles were prepared by the slow evaporation of toluene from homogeneous PMMA/PS/toluene droplets dispersed in aqueous solution of sodium dodecyl sulfate in advance. Appropriate molecular weights of PMMA and PS were necessary for occurrence of the cleavage of the Janus composite particle, resulting in PMMA and PS hemispherical particles. The cleavage depended on the composition of the acetone/water solution, which was explained by selective solvent absorption into the polymer phases. The results strongly support the cleavage mechanism of Janus composite polymer particles that had been proposed earlier.     

超浓乳液聚合制备PU/PS的SIPN粉状树脂研究

将聚氨酯予聚体 (PU ) 苯乙烯 (St)的复合体系 ,用超浓乳液聚合方法制备了半互穿聚合物网络(SIPN)复合聚合物 ,得到了用聚氨酯予聚体改性的聚苯乙烯 (PU/PS)SIPN粉状树脂 .研究了分散相的比例(α)和聚合温度对聚合稳定性及聚合转化率 -时间的关系 ;测定了聚合物胶乳粒子的大小、形态 ,玻璃化温度 ,动态力学性能等 .结果表明 ,超浓乳液聚合较之本体聚合具有较高的聚合速率 ,容易控制所制备的胶乳粒径 ,能够制得PU/PS复合聚合物的SIPN粉状树脂 .该粉状树脂便于加工 ,具有良好的强韧性 ,有利于扩大应用     

Emulsion polymerization of styrene and methyl methacrylate using a hydrophobically modified inulin and comparison with other surfactants

The use of a new class of graft polymer surfactants, based on inulin, in emulsion polymerization of poly(methyl methacrylate) (PMMA) and polystyrene (PS) particles is described. PS and PMMA were synthesized by emulsion polymerization, and stable particles with a high monomer content (50 wt %) were obtained with a very small amount of polymeric surfactant ([surfactant]/[monomer] = 0.0033). The latex dispersions were characterized by dynamic light scattering and by transmission electron microscopy to obtain the average particle size and the polydispersity index, and the stability was determined by turbidimetry measurements and expressed in terms of critical coagulation concentration. The last section gives a comparison of PMMA particles prepared by emulsion polymerization using classical surfactants from different types as emulsifiers with that obtained using the copolymer surfactant. It shows the superiority of INUTEC SP1 as it is the only one that allows stable particles at 20 wt % monomer content, with a smaller ratio [surfactant]/[monomer] = 0.002.