反胶束模板制备聚甲基丙烯酸甲酯/无机纳米粒子/石墨纳米复合材料及其表征

以甲基丙烯酸甲酯(MMA)和三氯甲烷(CHCl₃)为油相制备反胶束微乳液, 依靠表面活性剂十六烷基三甲基溴化铵(CTAB)自组装形成的“微反应器”作为模板成功地制备了PMMA/Eu(OH)₃/EG和PMMA/Ni(OH)₂/EG纳米复合材料. 并用红外光谱(IR)、扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)和差热-热重(TG-DTA)对该复合材料进行了表征和分析. 研究结果表明, 反胶束法可以有效地应用于有机-无机纳米复合材料的制备.     

SiO2交联剂交联MMA聚合制备PMMA/SiO2纳米复合材料

用SiO2交联剂(SiO2HPA)交联甲基丙烯酸甲酯(MMA)自由基聚合制备PMMA SiO2纳米复合材料。采用两步法将可聚合乙烯基单体以化学键的形式键接到SiO2表面合成SiO2交联剂,首先利用过量的甲苯2,4二异氰酸酯(TDI)对SiO2纳米粒子表面进行化学修饰合成出表面带有高反应活性NCO基团的功能化SiO2粒子(SiO2TDI),SiO2TDI与丙烯酸羟丙酯(HPA)反应合成SiO2交联剂。系统研究了MMA单体与SiO2交联剂投料比及聚合时间对聚合反应的影响。此外,利用红外光谱(FT IR)、DSC、TGA、可见光光谱仪等实验手段对纳米复合材料进行了表征分析。结果表明,纳米SiO2粒子在复合材料中起着物理交联点和化学交联点作用,复合材料玻璃化转变温度(Tg)明显地高于其纯PMMA的玻璃化转变温度,随着纳米SiO2粒子含量的增加,复合材料玻璃化温度升高,而透明度明显降低。     

微乳液聚合耦合共混法构建聚偏氟乙烯共混杂化膜

以苯乙烯和甲基丙烯酸甲酯混合物作为油相, 采用反相微乳液法制备了AgCl纳米粒子; 通过微乳液原位聚合油相单体得到包含AgCl纳米粒子的聚合乳液; 将聚合乳液与聚偏氟乙烯(PVDF)通过共混法构建了包含AgCl纳米粒子的PVDF共混杂化膜. 紫外-可见光谱、 透射电子显微镜(TEM)及扫描电子显微镜(SEM)等表征结果和超滤实验结果表明, 聚合乳液加入的同时引入了亲水性聚合物和表面亲水的AgCl纳米粒子, 不仅改善了PVDF共混杂化膜的孔隙率和平均孔径, 还显著增强了PVDF共混杂化膜的极性和亲水性, 最终提升了膜的水通量和抗污染性能; 过量聚合乳液加入后不能与PVDF材料均匀共混, 而且AgCl纳米粒子也会在膜中形成团聚物堵塞膜孔隙, 从而削弱了膜的水通量和抗污染性能.     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

铝纳米粒子表面引发聚合制备核壳纳米结构

利用硅烷偶联剂引发法制备核壳结构金属铝纳米粒子(Al NPs)@聚合物, 并研究了聚合反应时间和单体浓度对核壳结构尺寸的影响. 首先合成了硅烷偶联引发剂{2-溴-2-甲基-[3-(三甲氧基硅基)丙基]丙酰胺}, 并通过在甲苯中回流的方法, 将其锚定在金属铝纳米粒子表面. 然后, 在粒子表面引发甲基丙烯酸甲酯的原子转移自由基聚合, 形成聚甲基丙烯酸甲酯(PMMA)壳层. 通过核磁共振波谱仪(NMR)和傅里叶变换红外光谱仪 (FTIR)证明了引发剂和PMMA的成功接枝. 透射电子显微镜(TEM)图像表明, PMMA改性后的金属铝纳米粒子的尺寸和形貌基本不变, 且被厚度约为15 nm聚合物壳层完整均匀地包覆. 此外, 利用动态光散射(DLS)进一步揭示了聚合时间和单体浓度对核壳结构水合直径(D_h)的影响, 发现延长聚合时间或增加单体浓度均可显著提高核壳结构尺寸.     

纳米SiO_2粒子锚固偶氮引发剂及接枝聚甲基丙烯酸甲酯

对纳米SiO2 粒子锚固偶氮引发剂 ,进而引发甲基丙烯酸甲酯聚合而制备聚甲基丙烯酸甲酯(PMMA) 纳米SiO2 复合粒子进行了研究 .纳米SiO2 先用环氧型硅烷偶联剂处理 ,再与偶氮二氰基戊酸发生缩合反应而锚固上偶氮引发剂 ,通过差示扫描量热和元素分析证明了引发剂在纳米SiO2 表面的锚固 .通过改性纳米SiO2 存在下MMA的乳液聚合 ,制备得到了接枝率为 2 3 2 %、接枝效率为 36 1%的PMMA 纳米SiO2 复合粒子 .经乳液聚合后 ,纳米SiO2 粒子团聚程度减小 ,在水相中分散稳定 .     

新型乳液聚合制备疏松PMMA树脂及成粒机理

采用以水相为分散相、甲基丙烯酸甲酯 (MMA) 环己烷混合物为连续相的新型乳液聚合制备PMMA树脂 .发现 ,在未加乳化剂和加入少量Tween2 0乳化剂时 ,均可制备由初级粒子凝聚而成、无明显皮膜结构的疏松PMMA粒子 ,初级粒子粒径小于环己烷存在下MMA悬浮聚合得到的PMMA粒子的初级粒子 .根据聚合体系相构成、PMMA在MMA 环己烷混合液的溶解性及PMMA粒子粒径分布和形态的演变 ,提出了在分散水滴内乳液聚合形成初级粒子 生长 凝聚的新型乳液聚合成粒机理     

苯乙烯-甲基丙烯酸甲酯悬浮-乳液复合聚合过程中聚合物复合粒子组成的变化

采用苯乙烯(St)悬浮聚合过程中滴加甲基丙烯酸甲酯(MMA)乳液聚合组分,悬浮乳液复合聚合(SECP)方法,制备大粒径聚苯乙烯聚甲基丙烯酸甲酯(PS- PMMA)复合粒子.采用FTIR、1H- NMR、13C- NMR分析方法,研究SECP各个时期复合粒子中MMA- St链节摩尔比,发现悬浮粒子中MMA St链节摩尔比逐渐增大,而PMMA乳胶粒子中逐渐减少,表明悬浮相和乳液相间存在物质传递过程.悬浮粒子中MMA链节质量与MMA总投料质量比主要由乳胶粒子生成速率和乳胶粒子向悬浮粒子凝聚速率决定.最终得到的复合粒子除含PS和PMMA均聚物外,还含少量MMA-St共聚物.     

纳米SiO_2/聚甲基丙烯酸甲酯复合材料的制备和力学性能

通过悬浮聚合的方法,用不同表面结构的纳米SiO2对聚甲基丙烯酸甲酯(PMMA)进行原位改性,得到纳米SiO2/聚甲基丙烯酸甲酯复合材料;利用红外光谱仪分析了复合材料的界面化学结构,利用热分析仪测定了其热稳定性,并采用冲击试验机测定了其力学性能.结果表明,不同表面结构的纳米SiO2均参与甲基丙烯酸甲酯的聚合反应,与PMMA基体之间形成化学键;而表面修饰有双键的纳米SiO2更易与甲基丙烯酸甲酯聚合,能更有效地提高PMMA的抗冲击性能.     

反相微乳液中AgCl纳米粒子的可控合成与AgCl/GMA-MMA-AMPS共聚物有机-无机杂化膜的研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)为表面活性剂,在甲基丙烯酸缩水甘油酯(GMA)和甲基丙烯酸甲酯(MMA)混合物为油相的反相微乳液体系中合成了AgCl纳米粒子,然后通过微乳液聚合制备了AgCl/GMA-MMA-AMPS共聚物有机-无机杂化膜,并用于苯/环己烷混合物的渗透气化分离.利用紫外-可见光谱及透射电子显...     

Synthesis of nano-ZnO/poly(methyl methacrylate) composite microsphere through emulsion polymerization and its UV-shielding property

Nano-ZnO/poly(methyl methacrylate)(PMMA) composite latex microspheres were synthesized by in-site emulsion polymerization. The interfacial compatibility between nano-ZnO particles and PMMA were improved by treating the surface of nano-ZnO particles hydrophobically using methacryloxypropyltrimethoxysilane (MPTMS). TEM indicated that nano-ZnO particles present in nanosphere and have been encapsulated in the PMMA phase. FT-IR confirmed that MPTMS reacted with the nano-ZnO particle and copolymerized with MMA. It was clearly found from SEM that ZnO nanoparticles can be homogeneously dispersed in the PVC matrix. The absorbance spectrum of the nanocomposite polymer suggested that increasing the amount of nano-ZnO in composite particles could enhance the UV-shielding properties of the polymers. The nano-ZnO/PMMA composite particle could eliminate aggregation of ZnO nanoparticle and improve its compatibility with organic polymer. This means that the composite particles can be widely applied in lots of fields.     

Preparation of polymethyl methacrylate with well-controlled stereoregularity by anionic polymerization in an ionic liquid solvent

This study investigates the effect of ionic liquids (ILs) on the anionic polymerization of methyl methacrylate (MMA). Polymethyl methacrylate (PMMA), an isotactic polymer, is prepared by anionic polymerization at a high reaction temperature with an IL that acts as both solvent and additive. The most plausible reaction mechanism is determined using ¹H NMR and Fourier-transform infrared spectroscopy. The electrostatic interaction between MMA and the IL increases the apparent steric hindrance in MMA, resulting in the isotactic PMMA.     

本体聚合制备Sm(OPr~i)(TTA)_2/PMMA光致发光材料

合成了(异丙氧基)二(α-噻吩甲酰三氟丙酮基)钐[Sm(OPri)(TTA)2]配合物,并通过本体聚合制备Sm(OPri)(TTA)2/PMMA光致发光材料,采用IR1、H-NMR、XRD、DMTA、FS、ESEM对其进行表征.结果表明,Sm-(OPri)(TTA)2/PMMA在396 nm波长激发下在562、598、644 nm处发射很强的Sm3+离子4G5/2→6H5/2,4G5/2→6H7/2,4G5/2→6H9/2跃迁的特征荧光,其发光强度与Sm(TTA)3/PMMA相当;其储能模量E′、玻璃化温度Tg和粘流温度Tf均比PMMA有所提高;Sm(OPri)3/PMMA形成类似交联结构聚合物,而Sm(OPri)(TTA)2/PMMA为线型无定型结构聚合物.     

Synthesis of functional graft copolymers by solution copolymerization and their evaluation as dispersants in nonaqueous phase dispersion polymerization

The poly(HEMA‐co‐MMA‐g‐PMMA) graft copolymer was prepared with a poly(methyl methacrylate) (PMMA) macromonomer, 2‐hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA), and its application as a dispersant for the nonaqueous phase dispersion polymerization of polystyrene (PST) was investigated. Monodisperse PST particles were obtained with two‐dimensionally tailored graft copolymers, with the number of grafted chains controlled and the polar component (HEMA) in the backbone chains balanced. As for the reactor, a stirred vessel with moderate agitation yielded uniform polymer particles, whereas sealed glass ampules with an overturning motion yielded broader size distributions. Increasing the polarity of the solvent in the continuous phase yielded smaller polymer particles with a gradual deterioration of monodispersity. Uniform polymer particles with a coefficient of variation of less than 6% were obtained up to 30 wt % solid contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1788–1798, 2003     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.     

非水凝胶原位聚合法制备三异丙氧基钕/PMMA杂化材料的研究

通过三异丙氧基钕直接掺入MMA单体 ,迅速形成凝胶后进行原位聚合的方法制得三异丙氧基钕 /PMMA杂化材料 ,采用IR、TG、WAXD、DMTA、SEM等手段对其进行表征 .结果表明 ,三异丙氧基钕与MMA中的羰基因配位并导致交联形成了交联网状结构的杂化材料 .与PMMA相比 ,这种杂化材料具有优良的耐热性、耐溶剂性 ,高贮能模量 ,同时 ,该制备方法克服了稀土离子易缔合的缺点 ,获得了高稀土含量且均匀分布的三异丙氧基钕 /PMMA杂化材料     

Reverse Atom Transfer Radical Polymerization of MMA in the Presence of CaCO3/SiO2 Two-Component Composite Particles

Summary: We previously discovered that structurally well-defined polymer/inorganic composite particles, i.e., poly(methyl methacrylate) (PMMA)/CaCO₃/SiO₂ three-component composite particles, can be achieved via reverse atom transfer radical polymerization (ATRP), using 2,2′-azo-bis-isobutyronitrile as initiator and Cu^II bromide as catalyst. In the present study, the influence of the mass ratio of CaCO₃/SiO₂ two-component composite particles to methyl methacrylate (MMA) on the rate and behavior of the polymerization was studied in detail. The results illustrate that increasing the mass ratio of CaCO₃/SiO₂ two-component composite particles will decrease the overall rate of polymerization of MMA under standard reverse ATRP conditions. Thermal properties of the obtained well-defined particles were characterized and determined by thermogravimetric analysis (TGA). The results indicate that well-defined PMMA chains grafted on the surface of CaCO₃/SiO₂ particles were only degraded by random chain scission of C C linkages within the PMMA chain, which is different from the degradation of PMMA chains prepared via traditional radical polymerization. This difference is reasonably ascribed to the difference between the end groups of PMMA prepared via reverse ATRP and that via traditional radical polymerization, which has been confirmed by end group analysis measured by ¹H–NMR spectroscopy.     

Properties of matrix-grafted multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposites synthesized by in situ reversible addition-fragmentation chain transfer polymerization

Multi-walled carbon nanotubes (MWCNT)/poly(methyl methacrylate) (PMMA) nanocomposites were synthesized by the in situ reversible addition-fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) in the presence of MWCNTs, at which the bulk polymer was grafted onto the surface of nanotubes through the ??grafting through?? strategy. For this purpose, MWCNTs were formerly functionalized with polymerizable MMA groups. MMA and PMMA-grafted MWCNTs were characterized by Fourier-transform infrared spectroscopy, Raman, X-ray photoelectron spectroscopy, transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Dissolution of nanotubes was examined in chloroform solvent and studied by UV?Cvis spectroscopy. Thermogravimetric and degradation behavior of prepared nanocomposites was investigated by TGA. MWCNTs had a noticeable boosting effect on the thermal stability of nanocomposites. TGA thermograms showed a two-step weight loss pattern for the degradation of MWCNT-PMMA/PMMA nanocomposites which is contrast with neat PMMA. Introduction of MWCNTs also improved the dynamic mechanical behavior and electrical conductivity of nanocomposites. TEM micrograph of nanocomposite revealed that the applied methods for functionalization of nanotubes and in situ synthesis of nanocomposites were comparatively successful in dispersing the MWCNTs in PMMA matrix.