溶剂热法合成CdS纳米晶及其光学性质研究

以硫脲和醋酸镉为原料,采用溶剂热法在不同的反应介质和温度下合成了CdS纳米晶,比较了单胺与双胺对合成CdS纳米晶形貌的影响。采用透射电镜(TEM)、X射线粉末衍射仪(XRD)和荧光分光光度计(PL)对合成的CdS纳米晶结构和光学性能进行表征。结果表明:反应温度和反应介质对其形貌有影响,在双胺的条件下,60℃时合成了纯相的六方相CdS纳米棒;双胺条件下更易生成纳米棒,且高温下晶体的结晶性更好。PL分析表明,水(溶剂)热法制备的CdS的荧光光谱图与大多数CdS类似,均在440~480 nm和550 nm处存在发射峰,但较宽的发射峰蓝移说明材料的光学性质受到材料形貌和制备方法的影响。     

制备均一形貌的长二氧化钛纳米管

在温和的水热条件下,用碱溶液处理不同粒径的锐钛矿相和金红石相二氧化钛 纳米粉体,得到了不同形貌的二氧化钛纳米管,并用TEM,XRD,FT-Raman和BET等 对其进行了表征。金红石相的超细纳米晶有利于形成均一形貌的纳米管,用粒径仅 为7.2 nm的金红石相纳米粉体为前驱体得到了长度为500 nm的长二氧化钛纳米管。 用纳米晶反应活性对晶粒尺寸的依赖性及晶相稳定性解释了长纳米管的形成机理。     

TiO2纳米管阵列光电催化氧化处理氨氮废水

用电化学阳极氧化法制备了高度有序的钛基二氧化钛纳米管阵列薄膜。用场发射扫描电镜(FE-SEM)、X射线衍射(XRD)表征样品的形貌与晶型特征。以二氧化钛纳米管阵列为光阳极,石墨为对电极,测试了不同pH值和外加偏压条件下的光电流响应和光电催化氧化降解NH4Cl水溶液(以N计,100 mg·L-1)的效率。结果表明:所制备的TiO2纳米管阵列具有锐钛矿和金红石的混晶结构,且主要晶型为锐钛矿。光电流响应的强弱与光电催化氧化效率的高低相对应,降解氨氮废水的最佳条件为pH=11,偏压为1.0 V。     

制备均一形貌的长二氧化钛纳米管

在温和的水热条件下，用碱溶液处理不同粒径的锐钛矿相和金红石相二氧化钛 纳米粉体，得到了不同形貌的二氧化钛纳米管，并用TEM，XRD，FT-Raman和BET等 对其进行了表征。金红石相的超细纳米晶有利于形成均一形貌的纳米管，用粒径仅 为7.2 nm的金红石相纳米粉体为前驱体得到了长度为500 nm的长二氧化钛纳米管。 用纳米晶反应活性对晶粒尺寸的依赖性及晶相稳定性解释了长纳米管的形成机理。     

二氧化钛纳米晶溶胶内渗透电极对染料敏化太阳能电池的光伏性能的提高

以自制的过氧钛酸(PTA)水溶液为前驱体,用水热法制备了透明锐钛矿相二氧化钛溶胶.无需有机添加剂可得到直径小于7 nm的棒状二氧化钛纳米晶溶胶.通过将溶胶内渗透到染料敏化太阳能电池(DSSCs)的多孔二氧化钛电极后,消除了多孔电极内的大孔并改善了电极内纳米晶之间的连通性.用扫描电子显微镜(SEM)和光学轮廓仪对溶胶内渗透后的光阳极进行了表征.结果表明:小颗粒棒状二氧化钛纳米晶附着在多孔的二氧化钛表面,填充了电极由于烧结产生的大孔,并在多孔的二氧化钛内部形成了有利于电子传输的网络结构.与未经处理的多孔电极相比,改性后的光阳极组装成染料敏化太阳能电池后光电转化效率提高了64%.     

紫外光照射下丙炔光催化水解反应的研究 Ⅰ．纳米二氧化钛光催化剂的性能

 采用5种不同的纳米二氧化钛为光催化剂,考察了它们在丙炔水解反应中的光催化活性,并用X射线衍射和漫反射紫外－可见吸收光谱技术进行了表征．研究了催化剂表面物理化学性质与在丙炔光催化水解反应中的构效关系．实验结果表明,纳米二氧化钛光催化剂能够引发丙炔的光催化水解反应,生成乙烷和乙烯等产物;锐钛矿相纳米二氧化钛具有较高的光催化活性,在晶型相同的情况下,影响光催化活性的主要因素是催化剂的粒径和比表面积．     

低温水热法制备高活性纳米金红石相二氧化钛

采用低温水热法由TiC l3溶液直接制备了纳米二氧化钛,并研究了TiC l3溶液浓度、反应温度以及陈化时间对产物晶相、晶化程度、形貌以及尺寸的影响。结果表明:TiC l3溶液浓度对晶相有较大影响,高浓度下易获得混晶,低浓度下得到纯金红石相。反应温度和陈化时间主要影响产物的晶化程度和晶体的形貌、尺寸,对生成的晶相也有一些影响。在给定的反应条件下,获得了形状规整、尺寸约为15×80nm、晶化程度高的金红石相二氧化钛纳米棒。对甲基橙的光催化降解实验表明,这种金红石纳米颗粒的催化活性与市售纳米锐钛矿相二氧化钛相近。     

板式纳米碳纤维负载二氧化钛光催化复合材料的制备及降解甲基橙的研究

以板式纳米碳纤维为载体,采用酸性氧化法对载体进行预处理之后,使用钛酸异丙酯为钛源,高温水热法制备了二氧化钛/纳米碳纤维复合光催化剂,并考察了其对甲基橙的光催化去除能力及循环反应性能.复合材料中二氧化钛含量通过改变前驱体组成进行调节.材料的结构性能通过氮气吸附、X射线衍射(XRD)、能谱分析仪(EDS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、热重分析仪(TG-DSC)等测试技术进行了表征.结果表明,锐钛矿型的二氧化钛以纳米颗粒形式均匀分散在纳米碳纤维表面,从而形成了高度分散的二氧化钛/碳纤维纳米复合材料.另外,复合系统中中孔吸附作用的存在,与纳米二氧化钛的光催化产生协同作用,增强了复合材料在紫外光照射下对于水溶液中甲基橙的去除能力.在光照射下反应120 min时,不同担载量样品对甲基橙的去除率最高可达80.1%,不同煅烧温度样品最高可达79.2%.此外,光催化剂有着良好重复利用性能,3次循环反应后对甲基橙去除率仍可保持80.0%.     

水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用

本文报道了水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用.选择合适的有机碱胶化剂,能很好地控制二氧化钛纳米晶的生长,形成不同形貌和粒径的锐钛矿型二氧化钛纳米晶颗粒.染料敏化太阳能电池光电性能测试结果表明,以四乙基氢氧化铵为胶化剂合成的边长为8～13nm的正方形二氧化钛纳米晶构成的光阳极光电性能优于以四丁基氢氧化铵为胶化剂合成的边长为7～10nm的正方形二氧化钛纳米晶以及长18～35nm,宽10～18nm的长方形二氧化钛纳米晶构成的光阳极.用较高浓度的四甲基氢氧化铵胶化剂能合成球形或椭球形亚微米级二氧化钛颗粒,以其为散射中心在光阳极中构建散射层,染料敏化太阳能电池的光电转换效率能由6.77%提高到8.18%.     

聚乙二醇对纳米二氧化钛性质和应用的影响

二氧化钛纳米晶光催化材料是近年来发展起来的新型环境友好材料,国内外研究者在利用二氧化钛纳米晶光催化降解苯酚、氯酚、甲醛等污染物方面做了大量的研究工作。研究表明TiO2的3种晶型,锐钛矿型、金红石型和板钛矿型中,有光催化作用的主要是锐钛型和金红石型,其晶型和晶粒大小     

Morphological and phase evolution of TiO2 nanocrystals prepared from peroxotitanate complex aqueous solution: Influence of acetic acid

Nanosized anatase and rutile TiO₂ having different shape, phase and size have been prepared from aqueous solutions of peroxo titanium complex starting from titanium(IV) isopropoxide (TTIP), acetic acid and hydrogen peroxide (H₂O₂) in water/isopropanol media by a facile sol-gel process. The TiO₂ nanocrystals are characterized by powder X-ray diffraction (XRD), Raman spectroscopy, FT-IR spectroscopy, TEM, high resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED) techniques. The influence of pH and the sequence of addition of reaction contents on the phase and morphology of TiO₂ are studied. The reasons for the observation of only anatase and/or mixture of anatase and rutile are given.     

Nano sulfated titania as solid acid catalyst in direct synthesis of fatty acid amides

Nanosized sulfated titania was prepared by a sol-gel hydrothermal process. X-ray diffraction (XRD), transmission electron, and scanning electron micrographs (TEM and SEM), FT-IR specific surface area, and BET N(2) adsorption were employed to characterize the properties of the synthesized sulfated TiO(2). The results indicate that both anatase and rutile TiO(2) are obtainable. This prepared sulfated titania showed high catalytic activity in direct amidation of fatty acids as well as benzoic acids with various amines under solvent-free conditions.     

Mechanical properties of titania nanofiber mats fabricated by electrospinning of sol–gel precursor

Flexible mats of titania fibers are prepared by calcination of electrospun polyvinylpyrrolidone fibers containing titanium isopropoxide precursor. Structural investigation of the calcinated nanofibers by X-ray diffraction (XRD) and electron diffraction (ED) combined with the morphologies by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) show the titania fibers, with an average diameter of 180 nm, were comprised of anatase and rutile crystals. The mechanical, chemical and thermal properties of the titania fiber mats are further investigated by the techniques of Instron mechanical tester, thermogravimetric analyzer (TGA), and Fourier transform infrared spectroscopy (FT-IR). The titania fiber mat prepared in this method exhibited a significant flexibility with 461 MPa Young’s modulus.     

Temperature programmed desorption analysis of sol-gel-derived titania films

Sol-gel-derived titania films were analyzed by temperature programmed desorption (TPD) and X-ray diffraction (XRD) techniques. The relationship between the TPD curves measured for two types of titania gel films and their crystal structures was investigated. On the basis of the analyses, a preparation process for a titania sol solution containing anatase nanocrystals was designed and developed. Using this process, a colloidal anatase titania sol solution was prepared by heating aqueous titanium hydroxide containing HCl at 60°C for 2 h. The nanocrystal structure of the titania films obtained by coating the sol on glass substrates was confirmed by TPD and XRD measurements.     

Synthesis and characterization of the air-water interfacial TiO2/ZrO2 binary oxide film

TiO(2)/ZrO(2) binary oxide film was self-assembled using anionic surfactant (sodium dodecyl sulfonate (SDS)) as template and obtained at the air-water interface. X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to characterize the obtained film. The film was composed of many lamellar nanorods with a d spacing of 3.2 nm, and the lamellas were perpendicular to the lengthwise position of the rods. The energy-dispersive spectrum (EDS) was used for determining the titanium/zirconium atomic ratio. After being calcined, the sample decomposed to a mixture of anatase titania and tetragonal zirconia, and all the lamellar structure was broken.     

Ag负载TiO2纳米管微波辅助水热法制备及其光催化性能

以微波辅助水热法制备了二氧化钛纳米管,然后通过浸渍法在其表面负载了银纳米颗粒.所得样品用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、氮吸附、X射线光电子能谱(XPS)、紫外-可见漫反射等测试方法表征.微波加热处理可以大大缩短反应时间,产物为无定型纳米管,经高温焙烧后转变成锐钛矿型二氧化钛.所得纳米管的外径为7-8 nm,内径为5-6 nm,管长约200 nm,比表面积可达371 m2·g-1.负载的银分散在纳米管的表面,对纳米管的结构与晶型没有影响,但是拓宽了二氧化钛的光吸收范围,使吸收边红移至可见光区,并且有效抑制了光生电子空穴的复合.在可见光降解罗丹明B的实验过程中,与Ag负载的P25及纯二氧化钛纳米管相比,Ag负载二氧化钛纳米管具有更高的可见光催化活性,并且当Ag/Ti 物质的量的比为0.5%时,可见光催化性能最好.     

Influence of synthesis methods on zirconium doped titania photocatalysts

Synthesis of various zirconium doped titania based photocatalysts were carried out by adapting different synthetic strategies. Doping is done on commercially available anatase titania, sol-gel titania and template mediated sol gel titania. A comparative study of the various prepared photocataysts was done using physico-chemical characterization techniques such as X-ray diffraction (XRD), surface area- pore volume measurements, UV-VIS Diffuse reflectance spectra (DRS), elemental analysis (XRF) and transmission electron microscopic (TEM) studies. The effect of zirconium and preparation methods on the photocatalytic degradation of methylorange is studied extensively. Both the surface properties and photo activity of zirconium doped titania were found to have a great dependence on the preparation methods. Among the different photocatalytic systems, the catalyst prepared by doping in the presence of urea template was found to produce a maximum photodegradation of 97.5%.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

The effects of the crystallization rate of the mesoporous TiO2 on the stability of the mesoporous structure after reflux

A simple synthetic method was employed to prepare mesoporous titania with anatase crystalline walls and high photocatalytic activity. The properties and structures of mesoporous titania were characterized by means of low angle and wide angle X-ray diffraction (XRD), Fourier transform (FT)-IR spectra, transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and N₂ adsorption–desorption. The characteristic results clearly show that crystallization rate of the mesoporous titania affects the stability of the mesoporous structure after reflux, and that the anatase crystal in the mesoporous wall of mesoporous titania can stabilize the mesoporous structure. The photocatalytic activity of titania powder was evaluated from an analysis of the photodegradation of methyl orange under UV irradiation. The results indicate that the titania powder with mesoporous structure shows the highest photocatalytic activity.     

微乳法合成纳米SiO2/TiO2及其光催化性能

采用聚乙二醇辛基苯基醚(Triton X-100)/正己醇/环己烷/氨水微乳体系合成了纳米TiO2和SiO2/TiO2复合物,用X射线衍射、红外光谱和透射电镜对其结构进行了表征,并以甲基橙降解评价了其光催化性能,讨论了SiO2/TiO2摩尔比、晶相组成及粒径与光催化活性的关系.结果表明,SiO2/TiO2催化剂中形成了新的Ti-O-Si键和无定形SiO2;在纳米TiO2中复合SiO2能有效抑制锐钛矿向金红石的转变,增加锐钛矿的稳定性,并阻止TiO2晶粒的聚集生长.催化剂的光催化活性随金红石含量的增加而降低,加入适量SiO2能明显提高TiO2的光催化活性,其中摩尔比为1/7的SiO2/TiO2光催化活性最高.