一种高容量的层状Co-MOF基超级电容器电极材料

通过简单的溶剂热反应合成了一种钴基层状MOF（[Co（4,4''-bpy）（tfbdc）（H₂O）₂],Co-BTH,4,4''-bpy=4,4''-联吡啶,H₂tfbdc=四氟对苯二甲酸）,并考察了其作为超级电容器电极材料的性能。研究结果表明：Co-BTH电极具有良好的赝电容性能,包含高比电容和较好的倍率性能。在1 A·g^-1电流密度下和1 mol·L^-1 KOH溶液中,其比电容最大可达2 316 F·g^-1。在2 A·g^-1的电流密度下,循环1 000次后,电极的比电容仍然还有847 F·g^-1。良好的赝电容性能与Co-BTH的层状结构和小尺寸的纳米片有关。     

基于双核{Zn2(COO)4}次级构筑单元的二维发光配位聚合物的晶体结构和对Fe3+的检测

使用H2L配体（H2L=2-（1,3-dioxo-1H-benzo[de]isoquinolin-2（3H）-yl） terephthalic acid）和Zn²⁺通过水热反应,合成了一例基于双核{Zn₂（COO）₄}次级构筑单元的二维发光配位聚合物[Zn₂（L）₂（DMSO）₂（DMF）]（1）（DMSO=二甲亚砜,DMF=N,N-二甲基甲酰胺）。拓扑分析表明1结构中的双核{Zn₂（COO）₄}单元可视为4连接节点,并与作为连接子的L^2-形成（4,4）-网拓扑构型。1表现出对Fe³⁺离子的选择性发光猝灭响应,检测限为2.8 μmol·L^-1。1对Fe³⁺的检测具有良好的抗干扰性,且可通过DMF溶剂洗涤实现再生,可多次循环使用。     

介孔碳/石墨烯复合材料的制备及其醌类改性电容性能

首先利用硬模板法制备出介孔碳/石墨烯复合材料,然后向复合材料中引入具有赝电容活性的醌类分子进一步增大材料的电容性能。研究结果表明,负载30%（w/w）叔丁基氢醌的介孔碳/石墨烯复合材料具有最佳的电容性能,在电流密度为0.5 A·g^-1时,比电容值为355 F·g^-1;当电流密度高达30 A·g^-1时,其比电容值高达226 F·g^-1,比电容保持率为64%,表现出良好的速率特性。     

线状全固态CNTF@ZnCo-OH//CNTF@RGO超级电容器的制备与电化学性能

采用电化学沉积在碳纳米管纤维上复合锌钴氢氧化物纳米片（CNTF@ZnCo-OH）,并研究其电化学性能。实验结果表明CNTF@ZnCo-OH电极在2 A·g^-1的电流密度下比电容为748 F·g^-1,在10 A·g^-1的电流密度下循环2 000圈以后,比电容保持率高达110.4%。该优异循环性能得益于碳纳米管纤维基底的网络结构和ZnCo-OH的纳米片状结构。以CNTF@RGO（石墨烯）为负极、CNTF@ZnCo-OH为正极,组装线状全固态非对称CNTF@ZnCo-OH//CNTF@RGO超级电容器。该器件在0.5 A·g^-1电流密度下比电容为70 F·g^-1,2 000次循环后电容保持率为79.6%,并且在不同的弯曲状态下保持电化学性能不变,具有优良的机械稳定性。该非对称线状器件可以在0.8~1.4 V之间工作,其能量密度高达19.1 Wh·kg^-1,对应的功率密度为1 400.3 W·kg^-1。2个30 mm长的线状器件可持续点亮LED灯10 s。     

水热法合成球花状二硫化钼及其电化学性能

采用二水钼酸钠（Na₂MoO₄·2H₂O）和硫脲（CS（NH₂）₂）分别作为钼源和硫源,通过水热合成法获得球花状二硫化钼,其较佳的水热条件为：180℃下反应48 h,钼硫原子比为1：4,反应物浓度为0.001 mol·L^-1,在100 mL反应釜中的填充体积为90 mL。采用X射线衍射（XRD）、扫描电镜（SEM）和透射电镜（TEM）、对样品的物相和形貌进行了表征,并利用低温氮吸附BET模型测试了样品的比表面积。结果表明,合成的二硫化钼结晶性良好,平均粒径约为1 μm,比表面积约为87 m²·g^-1,分布均匀且无明显团聚。通过循环伏安（CV）曲线、恒电流充放电曲线（GCD）、阻抗谱图（EIS）表征其电化学性能,测试表明：在3 mol·L^-1 KOH水相电解液中,单电极比电容可达130.6 F·g^-1（扫速为5 mV·s^-1）和110.9 F·g^-1（电流密度为0.1 A·g^-1）,界面转移电阻R_ct为0.33 Ω;循环1 000圈后比电容损失为14.7%。说明采用该水热法合成的二硫化钼可以成为超级电容器电极的理想材料。     

扫帚状氧化铈制备及其对Pt基阳极催化剂催化性能的影响

采用水热合成法,合成了比表面积为175 m²·g^-1,孔径在2~4nm范围内的扫帚状CeO₂。通过微波辅助乙二醇还原氯铂酸法制备了Pt-CeO₂/RGO催化剂,探究扫帚状CeO₂的添加对Pt基催化剂电催化性能的影响。利用X射线衍射仪（XRD）、扫描电镜（SEM）、N₂吸附-脱附、X射线光电子能谱（XPS）对所制备的CeO₂及催化剂进行表征。利用电化学工作站对催化剂进行电化学性能测试。结果表明,催化剂中CeO₂保持原有扫帚状,Pt纳米粒子均匀分布于石墨烯载体表面;当m_RGO∶m_CeO2=1∶2时,添加了扫帚状CeO₂的Pt-CeO₂/RGO催化剂的电催化性能最优,电化学活性表面积为102.83 m²·g^-1,对乙醇氧化的峰值电流密度为757.17 A·g^-1,1 000 s的稳态电流密度为108.17 A·g^-1,对乙醇催化氧化反应的电荷转移电阻最小,活化能最低。     

木糖-软模板水热法制备硼掺杂分级多孔炭球及其电化学性能

以D-木糖为炭源,月桂酸钠为模板剂,硼酸为掺杂剂,通过水热炭化方法制得硼掺杂分级多孔炭球（BPC_S）。通过扫描电子显微镜（SEM）、透射电子显微镜（TEM）、N₂吸附-脱附测试、X射线光电子能谱（XPS）、顺磁共振波谱（EPR）、傅里叶红外光谱（FT-IR）、拉曼光谱（Raman）、X射线粉末衍射（XRD）、热重（TG）分析对样品进行表征。结果表明：月桂酸钠作为介孔造孔剂的同时,通过与D-木糖间的氢键作用使有机-有机自组装过程自发进行并形成窄尺寸分布（2~5 μm）规整炭球;硼酸在水热中催化炭源脱水降解,并以BC₃、BCO₂和BC₂O的形式掺杂在炭球上,掺硼后炭球与水表面接触角降低,润湿性提高。经CO₂活化、月桂酸钠高温分解以及胶质炭球的堆积分别产生微孔（0.5~1.2 nm）、介孔（3.14~35.00 nm）和大孔（60~146 nm）并形成分级结构。当硼酸加入量为0.927 5 g时多孔炭球（BPC_S-1）的电化学性能最佳,在6 mol·L^-1 KOH三电极体系中电流密度为0.5 A·g^-1时,比电容达287.12 F·g^-1;两电极体系中电流密度为0.5 A·g^-1时比电容达151.34 F·g^-1,能量密度达5.3 Wh·kg^-1;电流密度为5 A·g^-1时进行1 000次充放电循环,电容保持率仍达96.43%。     

双金属离子调控型镍钴氧化物纳米片用于非对称超级电容器

通过水热-煅烧两步法制备了系列镍钴氧化物（NCO）纳米片。通过改变前驱体溶液中的镍、钴离子物质的量之比,进而调控NCO纳米片中的过渡金属离子比例。NCO纳米片的晶相、形貌和结构利用X射线衍射、扫描电子显微镜和X射线光电子能谱表征。此外,对NCO纳米片的电化学性能进行测试。结果表明,NCO-2（Ni_1.95Co₁O_x）纳米片在0.5 A·g^-1电流密度下,比电容为1 096.88 F·g^-1,且经过5 000次循环后具有78.26%的循环稳定性。以NCO-2为正极、活性碳为负极构成的非对称超级电容器,在功率密度为576 W·kg^-1时,能量密度为57.70 Wh·kg^-1。     

碳酸盐共沉淀法可控制备超高倍率锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2

采用碳酸盐共沉淀法通过调节NH₃·H₂O用量来实现可控制备超高倍率纳米结构LiNi_1/3Co_1/3Mn_1/3O₂正极材料。NH₃·H₂O用量会对颗粒的形貌、粒径、晶体结构以及材料电化学性能产生较大的影响。X射线衍射（XRD）分析和扫描电镜（SEM）结果表明,随着NH₃·H₂O用量的降低,一次颗粒形貌由纳米片状逐渐过渡到纳米球状,且n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品晶体层状结构最完善、Li⁺/Ni²⁺阳离子混排程度最低。电化学性能测试结果也证实了n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品具有最优异的循环稳定性和超高倍率性能。具体而言,在2.7~4.3 V,1C下循环300次后的放电比容量为119 mAh·g^-1,容量保持率为81%,中值电压基本无衰减（保持率为97%）。在100C（18 Ah·g^-1）的超高倍率下,放电比容量还能达到56 mAh·g^-1,具有应用于高功率型锂离子电池的前景。此NH₃·H₂O比例值对于共沉淀法制备其他高倍率、高容量的正/负极氧化物材料具有一定的工艺参考价值。     

零维/二维MXene复合膜的制备及其超级电容器性能

采用水热法制备了0D/2D复合Ti₃C₂T_x MXene,利用X射线衍射、动态光散射和荧光光谱表征了其结构与形貌,结果表明形成了量子点吸附于纳米片的Ti₃C₂T_x复合结构（QDT）。相比未引入量子点的Ti₃C₂T_x,由QDT组装得到的自支撑膜电极的电化学性能有了显著提高：在三电极体系中,扫速为5 mV·s^-1时,比电容为338 F·g^-1,当扫速达到2 000 mV·s^-1,电容保持率达到46%;在两电极体系中,0.5 A·g^-1时的比电容达到216 F·g^-1,10 000次循环后电容保持率为87%。以上性能可归结于：量子点提供了更多的离子吸附位点,且纳米片尺寸减小,缩短了离子传输路径。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.