电感耦合等离子质谱法测定染铅猪仔的血铅、尿铅含量

利用电感耦合等离子质谱法测定染铅猪仔的血铅、尿铅含量.铅元素校正曲线的相关系数达到0.9999,方法检出限为0.08 μg/L.用冻干牛血铅、镉成分分析标准物质和冻干人尿铅成分分析标准物质验证了方法的准确性和重复性,分析结果表明,测定值与标准值基本吻合,测定值的相对标准偏差＜3.4％.用此方法分析了染铅猪仔不同时段的血...     

能量色散型X射线荧光光谱法测定聚合物材料中镉和铅含量

提出了能量色散型X射线荧光光谱测定聚合物材料中镉和铅的测试分析方法及制样技巧。按照仪器分析条件测定同时含有镉和铅的6块不同浓度级别的标准物质来建立校准工作曲线,其线性范围分别在250ug·g-1、1100ug·g-1以内。镉和铅的方法检出限依次为4.7ug·g-1、4.1ug·g-1。该方法应用于测定欧洲标准物质ERM-EC680和ERM-EC681k,其镉和铅的实际测定值与标准物质证书的标称值相符,测定实际样品中的镉和铅的回收率介于90~110%。该方法测定标准物质和实际样品中镉和铅的精密度均小于10%。     

同位素稀释电感耦合等离子体质谱(ID-ICP-MS)测定植物与人发标准物质中的铅

建立了同位素稀释电感耦合等离子体质谱(ID-ICP-MS)测定铅的方法.考察和讨论了仪器参数对同位素比值测定的影响,优化了仪器的数据采样参数.利用内标Tl对质量歧视、系统漂移进行了校正.讨论了同位素浓缩剂加入量对最终浓度测定值的不确定度的影响.将该方法应用于植物标准物质和人发标准物质的测定,结果令人满意.     

激光剥蚀多接收杯电感耦合等离子体质谱仪原位分析硫化物铅同位素组成

采用193 nm准分子激光与MC-ICP-MS质谱仪探讨了原位微区分析过程中物质基体效应对铅同位素测定的影响,指出选择基体匹配标准物质对测定硫化物铅同位素具有重要意义.通过模拟计算发现准确测定Tl与Hg的分馏因子关系,可以在204Hg/204 Pb＜2的范围内有效校对204Hg对204 Pb的干扰.研究表明,束斑直径(24～160μm)和剥蚀频率(2～20 Hz)并不影响铅同位素组成测试.改变激光剥蚀参数可以解决MC-ICP-MS信号检测范围较窄的问题.针对目前硫化物固体标准物质缺乏的现状,采用压片法和快速熔融法制备硫化物标准物质.压片样品铅同位素组成表现出较好的均一性,而不同批次快速熔融法样品存在铅同位素分馏,仅单次制造的熔融样品内部铅同位素组成具有均匀性.结果表明,虽然快速熔融法还存在一定缺陷,但这两种方法都有望成为硫化物标准样品制作方法的备选方案.利用本方法对天然硫化物样品(黄铁矿和闪锌矿)及人工合成硫化物样品的铅同位素组成进行了准确测定,测定值与溶液值在误差范围内一致.     

石墨炉原子吸收光谱法对高钙营养强化剂中痕量铅的测定

通过选择基本改进剂种类和石墨管类型,优化了灰化和原子化参数以及使标准系列与样品基体相匹配等一系列条件的测定,从而克服了石墨炉原子吸收法测定高钙营养强化剂中痕量铅时高含量钙对其的负干扰。实验结果表明：使用5％NH4H2PO4作为基体改进剂,普通石墨管,选择灰化温度1000℃并保持30s,原子化温度1400℃并保持3s,使用标准加入法使标准系列与样品基体相匹配,钙的干扰大大降低,同时高钙营养强化剂样品铅测定的回收率达到92％。使用标准物质（茶叶GBW 10016）对该方法进行了检验,结果表明铅的测定值在标准样品的保证值范围内。     

进口氧化皮化学特性及X射线荧光光谱分析

采用玻璃片法熔融进口氧化皮样品,并应用X射线荧光光谱法测定其中全铁和硅、铝、磷、钙、镁、钛、砷、铅等15种杂质元素的含量.根据氧化皮成分含量范围,利用多个铁矿石标准样品、部分标准样品添加基准物质Fe2O3配制系列校准物质,建立工作曲线.结果表明,该方法能准确、快速地对氧化皮进行分析,测量值与经典方法或标准值比较没有显著性差异.     

X射线荧光光谱法测定聚合物材料中铅和镉

提出了X射线荧光光谱法测定聚合物材料中铅和镉的方法。将粒径小于4mm的样品颗粒置于样品杯中,保持样品厚度大于16mm,加盖后按仪器工作条件进行测定。铅和镉的线性范围依次在1 033μg.g-1和980μg.g-1以内,检出限依次为0.31μg.g-1和0.69μg.g-1。方法用于分析标准物质(ERM-EC680k和ERM-EC681k),测定值与认定值相符。     

石墨炉原子吸收光谱法测定茶叶中的铅

采用石墨炉原子吸收光谱法测定茶叶中铅,以NH4H2PO4作为基体改进剂,提高了测定的灰化温度,消除了基体干扰.方法简便,快速,准确度高.通过对标准物质的多次测定,结果均在其保证值范围内,相对标准偏差为2.8%.对样品进行加标回收试验,回收率为96%～105%,方法检出限为0.12μg/L.     

火试金重量法直接测定铅精矿及其它含铅物料中的银

系统研究了火试金重量法直接测定铅精矿、铅矿石、铅合金和含铅物料中银含量的条件,将测定结果与国家标准、行业标准方法的测定结果进行比较,并采用铅精矿国家标准物质进行验证。结果表明:测定5~71 200g/t的银含量,相对标准偏差(RSD)和银标准加标回收率分别为0.10%~7.4%和99.10%~99.94%。分析结果与国家标准、行业标准方法测定结果吻合,验证结果与铅精矿国家标准物质认定值一致。     

火试金重量法直接测定铅精矿及其它含铅物料中的银

系统研究了火试金重量法直接测定铅精矿、铅矿石、铅合金和含铅物料中银含量的条件,将测定结果与国家标准、行业标准方法的测定结果进行比较,并采用铅精矿国家标准物质进行验证。结果表明:测定5~71 200g/t的银含量,相对标准偏差(RSD)和银标准加标回收率分别为0.10%~7.4%和99.10%~99.94%。分析结果与国家标准、行业标准方法测定结果吻合,验证结果与铅精矿国家标准物质认定值一致。     

Determination of trace Cd and Pb in environmental and biological samples by ETV-ICP-MS after single-drop microextraction

A method based on single-drop microextraction (SDME) combined with electrothermal vaporization (ETV)-ICP-MS was proposed for the determination of trace Cd and Pb. 8-Hydroxyquinoline (8-HQ) was employed as extractant dissolved in several microliters of chloroform and then an organic microdrop was formed at the tip of the microsyringe needle to extract the interest analytes. The vaporization behavior of the metal-8-HQ chelates in graphite furnace was investigated, and the ETV temperature program was optimized. The factors that influenced the extraction efficiency of target analytes (including pH value, flow rate of sample, extraction time and organic microdrop volume) were studied. Under the optimum conditions, the detection limits of the Cd and Pb were 4.6 and 2.9 pg mL⁻¹ with the enrichment factor of 140-fold for Cd and 190-fold for Pb, respectively. The proposed method was applied successfully to the determination of trace Cd and Pb in environmental and biological samples. In order to validate the developed method, a certified reference material of GBW 08501 peach leaves was analyzed and the determined values obtained were in a good agreement with the certified values.     

Improved immobilization of 8-hydroxyquinoline on polyacrylonitrile fiber and application of the material to the determination of trace metals in seawater by inductively coupled plasma mass spectrometry

A modified synthetic method has been developed for immobilization of 8-hydroxyquinoline on polyacrylonitrile fiber. The synthetic conditions, e.g. reagent concentration, reaction temperature and time, were optimized. The features of the newly-modified fiber are higher exchange capacity compared with most other materials containing immobilized 8-hydroxyquinoline, better mechanic characteristics, high stability at both high and low pH, and ease of synthesis. This modified fiber can concentrate and separate trace metals from matrices with higher concentrations of alkali and alkaline earth elements. To validate the characteristics of the modified fiber, trace metals Ag, Be, Cd, Co, Cu, Mn, Ni, Pb, and Zn in the certified reference materials river water (SLRS-4) and seawater (CASS-4, NASS-5, SLEW-3) were preconcentrated before determination by inductively coupled plasma mass spectrometry. Good agreement was obtained between the data obtained by this method and the certified values.     

Interferences removal for cadmium determination in samples with complex matrices by hydride generation coupled with non-dispersive atomic fluorescence spectrometry.

An intermittent on-line concentration and separation system coupled with HG-AFS was developed to eliminate serious interferences from Cu2+, Pb2+ and Zn2+ on the determination of cadmium. In the present method, the interferences from common coexisting ions, such as Cu2+, Pb2+, Zn2+, Fe3+ and Ni2+, were greatly reduced. Under the optimized conditions, a detection limit of 3 pg ml(-1) (3sigma, n=11) and a precision of 1.9% RSD for 1 ng ml(-1) of Cd were obtained. The method was successfully applied to the determination of cadmium in a series of Chinese Geological Reference Materials (SRMs) and GBW01621 ferronickel alloy using simple aqueous standard calibration technique. The results obtained were in good agreement with the certified values.     

Ultrasound-assisted pseudodigestion for toxic metals determination in fish muscles followed by electrothermal atomic absorption spectrophotometry: multivariate strategy

A simple and efficient procedure for the determination of arsenic (As), cadmium (Cd), and lead (Pb) in the edible parts of freshwater fish by ultrasonic-assisted acid pseudodigestion (USD) was developed. A Plackett-Burman experimental design was used as a multivariate strategy for the evaluation of the effects of several variables at once. Five variables--sonication time, sample mass of muscle tissue, temperature of the ultrasonic bath, mL of nitric acid, and mL of a mixture of acid and oxidant--were regarded as factors. From these studies, certain variables showed up as significant, and they were optimized by a 23+star central composite design, which involved 16 experiments. Optimum values of the variables were selected for the development of USD to determine the contents of As, Cd, and Pb in fish muscles used as pollution bioindicators from Lake Manchar (Sindh, Pakistan). The determination of the 3 toxic metals under study was performed by electrothermal atomic absorption spectrometry. The accuracy of the optimized procedure was evaluated by analysis of certified reference materials BCR 185R bovine liver and by comparison with conventional wet acid digestion methodology. The result obtained by the optimized method showed good agreement with the certified values and sufficiently high recovery. No significant differences were observed for P = 0.05. Relative standard deviation values (average of 10 separate determinations) were 1.21, 5.52, and 5.32% for As, Cd, and Pb, respectively.     

Ionic liquids based single drop microextraction combined with electrothermal vaporization inductively coupled plasma mass spectrometry for determination of Co,Hg and Pb in biological and environmental samples

A new method of ionic liquids based cycle flow single drop microextraction combined with electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) was proposed for the determination of trace Co, Hg and Pb with 1-(2-pyridylazo)-2-naphthol (PAN) as both extractant and chemical modifier and 1-butyl-3-methylimidazolium hexafluorophosphate as the extraction solvent. Several factors that influence the microextraction efficiency, such as sample pH, sample flow rate, microdrop volume and extraction time, were investigated and the optimized microextraction conditions were established. Co, Hg and Pb in the post-extraction ionic liquids phase were directly determined by ETV-ICP-MS with the use of PAN as chemical modifier. The chemical modification of PAN in ETV-ICP-MS was studied and the factors affecting the vaporization behaviors of target analytes were investigated. Under the optimized conditions, the detection limits of the method were 1.5, 9.8 and 6.7 pg/mL for Co, Hg and Pb, with the relative standard deviations for 0.5 ng/mL (n = 7) of Co, Hg and Pb were 7.7%, 5.2% and 12.0%, respectively. After 10 min of extraction, the enrichment factors were 350 (Co), 50 (Hg) and 60 (Pb). The proposed method was successfully applied to the determination of trace Co, Hg and Pb in human serum and environmental water samples. In order to validate the developed method, a certified reference material of human hair (GBW07601) was analyzed and the determined values were in good agreement with the certified values.     

Iridium as permanent modifier in the determination of lead in whole blood and urine by electrothermal atomic absorption spectrometry

The behavior of Iridium as a thermally deposited permanent modifier for the determination of lead by GFAAS was studied. The iridium coating procedure was optimized using a two-level factorial design. Using the optimized coating procedure, up to 1100 firings were possible with the same coating without sensitivity losses. The system was used in the determination of lead in whole blood and urine. A mixture of 0.1% Triton X-100 and 0.2% nitric acid was used as diluent. Pyrolysis temperature was 800°C for both matrices. Spiked, low-level samples were used for calibration. Under these conditions, no significant difference was found in comparison to the results obtained using a validated conventional modification procedure employing phosphate as modifier. Also, good agreement between found and certified/reference values were observed in the analysis of certified and commercial quality control materials, respectively. Such agreement was observed even using a 1100 times fired Ir coated platform–graphite tube assembly.     

On-line Preconcentration and Determination of Trace Metals in Water Samples by Flow Injection Combined with Flame Atomic Absorption Spectrometry via Calix[4]arene Carboxylic Acid Packed Micro-column

An adsorbent calix[4]arene carboxylic acid was employed as the adsorption material for on-line flow injection( FI) micro-column preconcentration coupled with flame atomic absorption spectrometry(FAAS) determination of trace heavy metals(Cu, Pb, Co, Ni and Cd). Parameters such as the pH, loading time and flow rate of sample, and the concentration, volume and flow rate of eluent were optimized. The enrichment factors are 50.0, 56.5, 11.6, 12.1 and 19.1 for Cu, Pb, Co, Ni, and Cd, respectively, and a sample throughput of 20 h^-1 was obtained. The limits of detection for Cu, Pb, Co, Ni, and Cd were in a range of 1.56―3.91 μg/L, and the relative standard deviations(RSDs) were less than 2.76%(n=7). Furthermore, the proposed method was successfully applied to the determination of Cu, Pb, Co, Ni, and Cd in certified reference materials and various water samples.     

Development of multi-elemental method for quality control of parenteral component solutions using ICP-MS

An inductively coupled plasma mass spectrometry (ICP-MS) method for elemental impurities determination in components used for parenteral nutrition solutions is proposed. Solutions of amino acids (10% m/v), glucose (50% m/v) and lipids (20% m/v) were analyzed. Arsenic, Cd, Cu, Pb and Mo were determined by ICP-MS operated at standard mode, whilst pneumatic nebulization was used for introducing the sample solution into the ICP. Mercury was determined using cold vapor generation (CVG) coupled to ICP-MS. Chromium, Mn, Ni and V were determined by means of dynamic reaction cell-inductively coupled plasma mass spectrometry (DRC-ICP-MS), while ammonia was used as reaction gas. The operational conditions of each technique were optimized in order to achieve better sensitivity, precision and accuracy. The influence of the sample matrix, mainly carbon, on all investigated elements was evaluated. The use of DRC was effective to reduce interferences on Cr, Mn, Ni and V determination. The other investigated elements (As, Cd, Cu, Pb, Mo and Hg) were determined directly in the samples, which were properly diluted. Results obtained were in good agreement (between 96 and 103%) with certified values (certified reference materials of water were analyzed), at the same time as the relative standard deviation was lower than 5%. Sample throughput was relatively high (up to 30 samples of components used for parenteral nutrition solution could be analyzed per hour). In this way, the proposed method can be recommended for routine analysis.     

Determination of lead and manganese in biological samples and sediment using slurry sampling and flame atomic absorption spectrometry

A procedure was developed for the determination of lead (Pb) and manganese (Mn) using slurry sampling. The two elements were detected using flame atomic absorption spectrometry with a slotted tube atom trap. Slurries were prepared by adding nitric acid solution (0.30%, w/v) to a powdered sample (0.10 g). After homogenization by ultrasonic bath for 15 min, the slurries were introduced directly into the detection equipment. Some conditions of the procedure were evaluated, such as acid concentration, presence of surfactants, and sonication time. Under optimized conditions, the LODs and LOQs achieved were 0.8 and 2.6 microg/g for Pb and 0.5 and 1.6 microg/g for Mn, respectively. The precision obtained varied between 3.1 and 5.8% (Mn), and 2.6 and 5.4% (Pb) for slurries of shrimp and sediment. The analytical curves were established using aqueous standards in nitric acid solutions. The accuracy of the method was assessed through the determination of Pb and Mn in the following certified reference materials: ERM-CE 278 (mussel tissue), CRM 397 (human hair), and SRM 1646a (estuarine sediment). The proposed procedure was successfully applied to the determination of Pb and Mn in six samples of shrimp powder, seasoning, and river sediment. The levels of Mn detected varied from 2.2 to 71.3 microg/g; Pb was detected in only one sediment sample (4.3 microg/g).     

X射线荧光光谱法分析镁砂的主次成分

采用镁砂标准样品作为校准样品,建立了熔融制样X射线荧光光谱法测定镁砂中MgO,Al2O3,SiO2,CaO,P2O5,Fe2O3的方法。采用熔融法为样品片和校准片的制备方法,选择四硼酸锂-偏硼酸锂（67＋33）为助熔剂,1.00mL LiBr溶液为脱模剂,熔融温度为1 100℃,熔融时间20min。对镁砂样品测定的相对标准偏差（RSD）小于3%,对不同镁砂标准样品进行测定,方法的测定结果与认证值相吻合。