MgCl2/Et3N催化合成α,β-不饱和氰代酯

用MgCl₂/Et₃N催化氰乙酸乙酯和芳香醛的缩合反应合成α,β-不饱和氰代酯, 反应可在室温进行. 产率87%～92%.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

空气中合成固溶体荧光粉Ba2(Zn, Mg)Si2O7:Ce3+,Eu2+,Eu3+及其发光特性

采用高温固相法在空气中合成了Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu,yCe³⁺系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu²⁺离子的4f⁶5d¹-4f⁷跃迁,590~725 nm红光区窄带谱源于Eu³⁺的⁵D₀-⁷F_J (J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu³⁺在Ba_1.97-yZn_1-xMg_xSi₂O₇基质中被还原成了Eu²⁺;当x=0.1时,荧光粉Ba_1.97Zn_0.9Mg_0.1Si₂O₇:0.03Eu的绿色发光最强,表明Eu³⁺被还原成Eu²⁺离子的程度最大。当共掺入Ce³⁺离子后,形成Ba_1.97-yZn_0.9Mg_0.1Si₂O₇:0.03Eu,yCe³⁺荧光粉体系,其发光随着Ce³⁺离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba_1.96Zn_0.9Mg_0.1Si₂O₇:0.01Ce³⁺,0.03Eu的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba₂Zn_0.9Mg_0.1Si₂O₇基质中的能量传递与发光机理。     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

LixNi0.5Co0.5O2的态密度计算及电化学性能研究

>为获得综合性能更好的锂离子二次电池正极材料, 分析了Co掺杂对Li_xNiO₂电化学性能的影响. 采用密度泛函DFT理论对Li_xNiO₂和Li_xNi_0.5Co_0.5O₂的平均放电电压和态密度进行了计算. 同时, 用共沉淀法制备了Li_xNiO₂和Li_xNi_0.5Co_0.5O₂锂离子二次电池正极材料, 并对其进行了XRD结构分析和恒流充放电测试. 实验和计算结果表明: 随锂离子嵌入正极(电池放电), 电池的电压逐渐降低, 材料的态密度峰向低能量方向移动; 与Li_xNiO₂相比, Li_xNi_0.5Co_0.5O₂的电压平台相对较高(当0.25≤x≤0.5), 而且在Li^＋嵌/脱时, Li_xNi_0.5Co_0.5O₂的结构变化相对较小; Co离子的掺入, 减小了NiO₆八面体的畸变度, 使材料的电化学稳定性得以提高. 在钴掺杂镍酸锂体系中, NiO₆和CoO₆具有相互的稳定作用.     

Ba0.4Sr0.6Co1-xFexO3-δ系阴极材料的制备和表征

采用甘氨酸-硝酸盐(GNP)法合成了中温固体氧化物燃料电池阴极材料Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ(x=0.0～0.8)系列粉体。利用XRD和SEM对材料的结构和微观形貌进行分析,用直流四端子法测量了烧结陶瓷体在中温(450～800 ℃)范围内的电导率。结果表明,制备的样品为单一钙钛矿相,随着Fe含量增加,XRD衍射峰值向高角度方向稍有偏移。电导率随着温度及Fe含量的变化出现极大值,在x＜0.2时,Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ系列烧结体在中温(450～800 ℃)区的电导率,随Fe掺入量的增大而增大,x=0.2样品的电导率最高,800 ℃时达244.7 S·cm^-1,远超过文献报道值,进一步增大Fe含量导电性能变差。     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

Ba0.98Bi0.02(Ti0.9Zr0.1)1-xCuxO3陶瓷的介电性能、弛豫行为与结晶化学特性

采用固相合成法, Bi3+作施主掺杂A位, Cu₂₊作受主掺杂B位, 制备了Ba_0.98Bi_0.02(Ti_0.9Zr_0.1)_1-xCu_xO₃(x=0, 0.01, 0.02, 0.03)陶瓷样品。借助XRD、LCR等研究了该陶瓷的结构与介电性能。结果表明:当x=0.03时, 陶瓷样品出现第二相。通过GULP模拟, 缺陷偶极子的稳定性从低到高依次为:[2Bi_Ba^·+V_Ba"]、[2Bi_Ba^·+Cu_Ti/Zr"]、[Cu_Ti/Zr"+V_O^··], 结合实验可知:介电弛豫程度与晶体中缺陷偶极子的存在形式相关, 其中x=0.01时, 晶体中以[2Bi_Ba^·+Cu_Ti/Zr"]为主。随Cu₂₊掺杂量的增加, 介电常数增加, 介电常数与B位键价和呈反比变化、与八面体BO₆的体积呈正比变化。     

LiNi1-xMxVO4的红外光谱和拉曼光谱研究

The vanadates of LiNi_1-xM_xVO₄(M=Fe,Co,Ni) containing VO₄ tetrahedrons were synthesized by soft chemical method through a new mild liquid route. The samples sintered at 450℃ for 3h and at 650℃ for 3h are named for LT-LiNiVO₄ and for MT-LiNi_1-xM_xVO₄ respectively. All of the products were measured by X-ray diffraction, IR and Raman spectra respectively. In comparison with IR spectra of V₂O₅ and NiO, the LT-LiNiVO₄ has a strong and broad IR absorption band of VO₄ tetrahedrons located at 600～850cm^-1 with three small splitting peaks corresponding to the asymmetry stretching vibrations of V-O bonds. The results of IR and Raman spectra for MT-LiNi_1-xM_xVO₄ show that the cations of Ni²⁺, Co²⁺, Fe²⁺ have the influences on the frequency shifts of the V-O vibrations.     

Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

xLi2MnO3-(1-x)LiNi0.7Co0.3O2的低温燃烧合成及电化学性能研究

采用低温燃烧法合成了锂离子电池正极材料xLi₂MnO₃-(1-x)LiNi_0.7Co_0.3O₂,对合成产物的结构、形貌和电化学性能进行了系统的研究, 通过单因素试验对合成条件和材料的组成进行了优化。结果表明:采用低温燃烧法合成的富锂层状正极材料具有α-NaFeO₂型层状结构、球状形貌和良好的电化学性能;其最佳合成条件为:回火温度850℃, 回火时间20 h;Li₂MnO₃的最佳配比为x=0.7.在此条件下合成的0.7Li₂MnO₃-0.3LiNi_0.7Co_0.3O₂,最高放电比容量达到263.1 mAh·g^-1,并具有良好的循环性能和倍率性能。     

纳米γ-Fe2O3粉体的合成与磁性增强研究

采用微乳法合成出氧化铁的前驱体——纳米β-FeOOH, 分别以β-FeOOH与添加剂壬基酚聚氧乙烯醚(NP-4)以物质量的比(n)为4, 5, 100添加NP-4, 混合煅烧. 采用拉曼光谱分析了样品中炭含量及分布, 并且用透射电镜观测产物的形貌和粒径, 采用磁强计观测产物磁性的变化. 结果得出, 对n＝5或破乳所得凝胶煅烧, 所得样品皆为分散均匀的四方形颗粒状, 且为磁性明显增强的纳米氧化铁γ-Fe₂O₃. 还分别讨论了样品中炭含量以及颗粒形状对比饱和磁化强度σ_s、矫顽力、矩形比的影响.     

CO2在纳米SiO2/TiO2悬浮体系中的光催化还原

用水热法合成了氧化硅改性的具有高比表面积、高催化活性的锐钛型二氧化钛, 并在其悬浮体系中将CO₂光催化还原合成甲醇. 采用XRD, TEM, 物理吸附, UV-Vis吸收光谱和FTIR等表征手段对催化剂结构特征进行了研究. 结果表明: 添加氧化硅后, 氧化硅和二氧化钛之间形成Si—O—Ti键, 抑制了TiO₂晶粒生长, 提高了锐钛型TiO₂的比表面积, 且随着含硅量的增加, SiO₂/TiO₂的UV吸收逐步蓝移, 禁带宽度增加. 还原反应结果表明: SiO₂/TiO₂具有光催化还原活性, 且随着含硅量的增加先增加后减小, 当SiO₂质量分数为3.5%时, SiO₂/TiO₂复合催化剂反应活性最强, 5 h内甲醇产量可达到21.0 mg/L, 并有少量甲醛生成.     

锂离子电池正极材料LiNi0.75-xCoxMn0.25O2的合成及电化学性能研究

以LiOH·H₂O、Ni(OAc)₂·4H₂O、Co(OAc)₂·4H₂O和MnO₂为原料，在水热反应釜中预处理，然后进行高温固相反应，合成了一系列锂镍钴锰氧化物LiNi_0.75-xCo_xMn_0.25O₂(x=0.05,0.10,0.15,0.20,0.25)。通过X射线衍射(XRD)、扫描电子显微镜（SEM）和电化学性能测试对所得样品的结构、形貌、粒径及电化学性能进行了表征。结果表明，当x=0.20时，所合成的正极材料具有很好的α-NaFeO₂型层状晶体结构，晶胞参数a=0.286 1 nm，c=1.416 4 nm， V=0.100 4 nm³，以50 mA·g^-1的电流密度在3～4.3 V(vs Li/Li⁺)充放电时，首次放电比容量达172.5 mAh·g^-1，首次放电效率高达90.9%，30个循环后其放电比容量依然保持在161.1 mAh·g^-1。     

纳米Ce1—xMnxO2催化剂上乙醇催化氧化发光研究

研究了纳米Ce_1—xMn_xO₂上乙醇催化氧化发光特性, 重点考察了反应温度和催化剂组成(Ce/Mn比)对发光强度的影响规律. 为研究催化发光机理, 在相近的反应条件下考察了纳米Ce_1—xMn_xO₂上乙醇催化氧化反应的活性和选择性. 结果表明: 催化发光强度与催化反应中生成CH₃CHO的产率有很好的顺变关系, 表明CH₃CHO是导致C₂H₅OH分子在纳米Ce_1—xMn_xO₂催化剂上氧化发光的“活性分子”.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

CO2在纳米SiO2/TiO2悬浮体系中的光催化还原

用水热法合成了氧化硅改性的具有高比表面积、高催化活性的锐钛型二氧化钛, 并在其悬浮体系中将CO₂光催化还原合成甲醇. 采用XRD, TEM, 物理吸附, UV-Vis吸收光谱和FTIR等表征手段对催化剂结构特征进行了研究. 结果表明: 添加氧化硅后, 氧化硅和二氧化钛之间形成Si—O—Ti键, 抑制了TiO₂晶粒生长, 提高了锐钛型TiO₂的比表面积, 且随着含硅量的增加, SiO₂/TiO₂的UV吸收逐步蓝移, 禁带宽度增加. 还原反应结果表明: SiO₂/TiO₂具有光催化还原活性, 且随着含硅量的增加先增加后减小, 当SiO₂质量分数为3.5%时, SiO₂/TiO₂复合催化剂反应活性最强, 5 h内甲醇产量可达到21.0 mg/L, 并有少量甲醛生成.