针状纳米SrFe12O19的溶胶-凝胶法制备及磁性研究

采用柠檬酸-EDTA的联合络合溶胶-凝胶法制得了针状纳米锶铁氧体磁性微粒。利用XRD对样品的物相进行分析,利用TEM对样品形貌和粒径进行表征,并利用振荡样品磁强计(VSM)对样品进行了磁性能研究。结果表明,相对于柠檬酸法制备的纯锶铁氧体微粒,EDTA加入后制备的SrFe₁₂O₁₉微粒仍保持六方磁铅石型结构,但是粒径减小,形貌向一维发展,且内禀矫顽力H_c显著提高。并直接对凝胶加热,使其发生自蔓延燃烧,省去了凝胶的干燥过程,制备周期缩短1/4以上,同时自蔓延燃烧使SrFe₁₂O₁₉的内禀矫顽力提高10%左右,通过洗涤前驱体使得SrFe₁₂O₁₉纯度得到提高,进而使比剩余磁化强度和比饱和磁化强度提高20%左右,最终制得了粒径为30 nm,长径比为5∶1,内禀矫顽力、比饱和磁化强度与比剩余磁化强度分别为6 446.9 Oe、68.9 emu·g^-1和40.2 emu·g^-1的针状纳米SrFe₁₂O₁₉。     

钡铁氧体微管的制备及镧掺杂对其性能的影响

以Ba(NO₃)₂和Fe(NO₃)₃为原料与不同比例的柠檬酸在水溶液中形成溶胶,把溶胶滴于脱脂棉模板上,水分挥发后在脱脂棉表面形成凝胶,于马弗炉中850 ℃煅烧2 h后制得了BaFe₁₂O₁₉微管,并在最佳柠檬酸用量时对BaFe₁₂O₁₉微管进行掺杂制得了BaLa_xFe_12-xO₁₉(x=0～0.3)微管。利用X射线衍射(XRD)﹑扫描电子显微镜(SEM)﹑透射电子显微镜(TEM)对样品的物相﹑形貌和粒径进行表征,并利用振荡样品磁强计(VSM)对样品进行磁性能研究。结果表明：借助脱脂棉模板,采用溶胶凝胶法制备了外径在8～13 μm之间,壁厚在0.5～2 μm之间的BaFe₁₂O₁₉微管,柠檬酸的加入使得微管出现破裂,随着柠檬酸用量的增加,BaFe₁₂O₁₉微管的矫顽力和饱和磁化强度先提高后下降,随着La掺入量的增加BaFe₁₂O₁₉微管的矫顽力、饱和磁化强度以及剩余磁化强度都先增加后减小,但饱和磁化强度和剩余磁化强度的最大值滞后于矫顽力的最大值,当柠檬酸与金属离子的物质的量之比为1∶1,x为0.05时850 ℃煅烧后制得了矫顽力、饱和磁化强度和剩余磁化强度分别为6 153.6 Oe,61.1和36.1 emu·g^-1的BaLa_xFe_12-xO₁₉微管。并就柠檬酸和La掺杂对微管的形成和磁性能的影响原理做了系统的研究。     

多孔软硬磁Ni0.5Zn0.5Fe2O4/SrFe12O19复合纤维制备及吸波性能

通过静电纺丝技术制备了多孔软硬磁Ni_0.5Zn_0.5Fe₂O₄/SrFe₁₂O₁₉复合纤维,利用综合热重分析仪（TG-DSC）、X射线衍射仪（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线能谱仪（EDS）和矢量网络分析仪（VNA）等对复合纤维的晶体结构、微观形貌和电磁性能进行了表征,研究了不同软硬磁质量比对纤维结构和性能的影响。结果表明：900℃下制备的复合纤维具有立体多孔结构,软硬磁质量比为1∶3时,复合纤维的比表面积达到55 m²·g^-1。吸波性能测试结果显示,当吸波剂涂层厚度为3.5 mm时,复合纤维在10.6 GHz处反射损失（R_L）值达到-31.9 dB,在2~18 GHz频率范围内,R_L值小于-10 dB的吸收带宽达到10.5 GHz,覆盖了整个X波段（8.2~12.4 GHz）和Ku波段（12.4~18 GHz）,显示出优异的宽波段吸收性能。     

柠檬酸根对纳米Fe3O4颗粒的生长及性能的影响

现代诊断学的发展使得超小超顺磁性的Fe₃O₄粒子在医学领域具有重要应用价值。实验中利用某些羧酸盐对铁氧化物晶粒成长的抑制作用，在共沉淀法中引入柠檬酸根，制备出平均粒径小于5 nm的Fe₃O₄纳米分散体系。研究了不同柠檬酸根浓度对生成粒子的大小、结晶和表面吸附情况的影响。对Fe₃O₄颗粒在不同条件下的磁性与胶体稳定性进行了讨论。     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

Co3O4纳米片的制备及其电化学电容性能

以配位超分子化合物为前驱物,通过液相氧化分解得到了六方形CoOOH纳米片,进而在空气中热处理制得了Co₃O₄纳米片。利用XRD、TEM、FESEM对CoOOH和Co₃O₄纳米片的结构和形貌进行了表征。电化学测试表明,Co₃O₄纳米片电极在6 mol·L^-1 KOH溶液中表现出良好的电化学电容特性,在电流密度为1 A·g^-1其单电极比容量可达到227 F·g^-1。     

纳米Re2O7的萃取法制备及光催化特性研究

本工作从N235-正庚烷萃取体系中，以饱和萃取法制得前体物和纳米粉体Re₂O₇，平均粒径30 nm。以此纳米粉为光催化剂，研究了光降解甲基橙染料的最佳条件，并在相同条件下，与非纳米Re₂O₇及工业常用的纳米TiO₂进行比较，光降解甲基橙能力大小为：纳米Re₂O₇ > 锐钛矿型纳米TiO₂ > 非纳米Re₂O₇。     

Mn2O3纳米结构的简易合成与电化学性质

用简易的室温或水热方法制备出不同形貌的MnCO₃微结构。经600 ℃热处理后,室温制备MnCO₃转变成Mn₂O₃胶体片,而水热制备MnCO₃样品则形成多孔Mn₂O₃纳米结构。然而,室温制备MnCO₃经120 ℃热处理后形成Mn₂O₃晶相。制备样品经过XRD和SEM表征表明,热处理MnCO₃前驱物形成Mn₂O₃过程导致产物形貌与结构变化。其形成机理又通过TEM和FTIR进一步研究。Mn₂O₃纳米结构的电容性质通过循环伏安法表征,结果表明Mn₂O₃形貌与结构对其电容有重要影响。     

不同形貌Fe3O4纳米粒子的氧化沉淀法制备与表征

用一种方法成功合成出了球体、四方体、八面体、不规则多面体、三角形和不规则颗粒等六种具有不同形貌的Fe₃O₄纳米粒子，通过扫描电子显微镜(SEM)表征了粒子形貌。试样经过X-射线衍射(XRD)表征具有尖晶石结构，且结晶良好。经震动样品磁强计(VSM)测定，各种形貌的Fe₃O₄纳米粒子都具有良好的磁性，其中八面体形貌的Fe₃O₄纳米粒子的饱和磁化强度达到86.56 emu·g^-1，剩磁为10.64 emu·g^-1，矫顽力为138 Oe。讨论了不同形貌的Fe₃O₄纳米粒子的形成机制，得出了晶核的生长环境对纳米粒子的形貌有重要影响的结论。     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料:制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li₄Ti₅O₁₂/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物, 进一步高温热处理, 在热剥离石墨烯的孔道内原位形成Li₄Ti₅O₁₂纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中, 热剥离石墨烯的三维连续结构确保了Li₄Ti₅O₁₂纳米粒子与石墨烯在长循环过程中的有效接触。因此, 复合材料表现出优异的循环稳定性。在5C下, 5 000次循环后, 其容量保持率高达94%。     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

g-C_3N_4/CaTi_2O_5复合材料制备及其光催化性能

利用类石墨氮化碳(g-C_3N_4)和亚稳相钙钛氧化物(CaTi_2O_5)固相法制备C_3N_4/CaTi_2O_5复合材料。利用X射线衍射(XRD)、金相显微镜、扫描电子显微镜(SEM)及附带能谱分析仪(EDS)和N2吸附-脱附对样品的显微结构和比表面积进行检测分析,并用紫外-可见吸收光度计(UV-Vis)测试了样品的光吸收性能,研究C_3N_4与CaTi_2O_5物质的量之比(nC_3N_4/nCaTi_2O_5)对C_3N_4/CaTi_2O_5复合样品的物相结构和微观形貌的影响,同时考察C_3N_4/CaTi_2O_5复合样品在可见光照射下光催化降解罗丹明染料效果。实验结果表明:相比纯C_3N_4和CaTi_2O_5样品,C_3N_4/CaTi_2O_5复合样品在可见光下具有较高的光催化性能,随着nC_3N_4/nCaTi_2O_5增加,样品的光催化降解率随之增加而后降低,当nC_3N_4/nCaTi_2O_5=1∶1时,样品的光催化降解率达到最大值99.5%,并且循环重复利用5次后,样品的光催化剂降解率仍几乎保持不变。复合样品光催化性能提高主要归因于复合能级结构有效地抑制了电子和空穴复合所致。     

Magnetic diphase nanostructure of ZnFe2O4/γ-Fe2O3

Magnetic diphase nanostructures of ZnFe₂O₄/γ-Fe₂O₃ were synthesized by a solvothermal method. The formation reactions were optimized by tuning the initial molar ratios of Fe/Zn. All samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, and Raman spectra. It is found that when the initial molar ratio of Fe/Zn is larger than 2, a diphase magnetic nanostructure of ZnFe₂O₄/γ-Fe₂O₃ was formed, in which the presence of ZnFe₂O₄ enhanced the thermal stability of γ-Fe₂O₃. Further increasing the initial molar ratio of Fe/Zn larger than 6 destabilized the diphase nanostructure and yielded traces of secondary phase α-Fe₂O₃. The grain surfaces of diphase nanostructure exhibited a spin-glass-like structure. At room temperature, all diphase nanostructures are superparamagnetic with saturation magnetization being increased with γ-Fe₂O₃ content.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

A new 2212-type stair like structure: Bi14Sr21Fe12O61, m=5 member of the generic [Bi2Sr3Fe2O9]m[Bi4Sr6Fe2O16] family

A new oxide, Bi₁₄Sr₂₁Fe₁₂O_61, with a layered structure derived from the 2212 modulated type structure Bi₂Sr₃Fe₂O₉, was isolated. It crystallizes in the I2 space group, with the following parameters: a=16.58(3) Å, b=5.496(1) Å, c=35.27(2) Å and β=90.62°. The single crystal X-ray structure determination, coupled with electron microscopy, shows that this ferrite is the m=5 member of the [Bi₂Sr₃Fe₂O₉]_m[Bi₄Sr₆Fe₂O₁₆] collapsed family. This new collapsed structure can be described as slices of 2212 structure of five bismuth polyhedra thick along , shifted with respect to each other and interconnected by means of [Bi₄Sr₆Fe₂O₁₆] slices. The latter are the place of numerous defects like iron or strontium for bismuth substitution; they can be correlated to intergrowth defects with other members of the family.     

Raman scattering investigations on lanthanum-doped Bi4Ti3O12-SrBi4Ti4O15 intergrowth ferroelectrics

The ferroelectric ceramics of Bi₄Ti₃O₁₂, SrBi₄Ti₄O₁₅, and lanthanum-doped Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅ were synthesized, and their Raman spectra were investigated. La-doping resulted in the enlargement of remnant polarization of Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅. The structure of the Bi₂O₂ layers and TiO₆ octahedra of the intergrowth was found to be different from those of Bi₄Ti₃O₁₂ and SrBi₄Ti₄O₁₅. La³⁺ ions exhibit pronounced selectivity for the occupation of A site as La content is lower than 0.50, and tend to be incorporated into Bi₂O₂ layers when the La content is higher than 0.50. Lanthanum substitution brings about the structural phase transition in Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅. The variation of ferroelectric property may be attributed to combined contribution from the decreasing of the oxygen vacancies, the relaxation of the lattice distortion, the destroying of the insulation and the space charge compensation effects of the Bi₂O₂ slabs.     

Crystal growth, structural characterization and magnetic properties of Ca3CuRhO6, Ca3Co1.34Rh0.66O6 and Ca3FeRhO6

Single crystals of Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆ and Ca₃FeRhO₆ were synthesized by high temperature flux growth in molten K₂CO₃ and structurally characterized by single crystal X-ray diffraction. While Ca₃Co_1.34Rh_0.66O₆ and Ca₃FeRhO₆ crystallize with trigonal (rhombohedral) symmetry in the space group , Z=6: Ca₃Co_1.34Rh_0.66O₆a=9.161(1) Å, c=10.601(2) Å; Ca₃FeRhO₆a=9.1884(3) Å, c=10.7750(4) Å; Ca₃CuRhO₆ adopts a monoclinic distortion of the K₄CdCl₆ structure in the space group C2/c, Z=4: a=9.004(2) Å, b=9.218(2) Å, c=6.453(1) Å, β=91.672(5). All crystals of Ca₃CuRhO₆ examined were twinned by pseudo-merohedry. Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆, and Ca₃FeRhO₆ are structurally related and contain infinite one-dimensional chains of alternating face-sharing RhO₆ octahedra and MO₆ trigonal prisms. In the monoclinic modification, the copper atoms are displaced from the center of the trigonal prism toward one of the rectangular faces adopting a pseudo-square planar configuration. The magnetic properties of Ca₃CuRhO₆, Ca₃Co_1.34Rh_0.66O₆, and Ca₃FeRhO₆ are discussed.