以离子液体为流动相添加剂高效液相色谱法分离钩藤药材中的钩藤碱和异钩藤碱

以常用流动相添加剂三乙胺作为对照,建立了以离子液体为流动相添加剂,分离钩藤药材中钩藤碱和异钩藤碱的高效液相色谱方法。以分离度及相关色谱参数为指标,选择了离子液体中咪唑阳离子烷基链长度及阴离子的种类。并分别考察了咪唑阳离子烷基链长度、离子液体浓度、流动相pH值和流动相比例对钩藤碱和异钩藤碱分离的影响,初步探讨了离子液体的分离机理。结果显示,咪唑阳离子的烷基链越长,阴离子的离子液体序列越高,分离效果越好,即[HMIM][BF_4]为最优的流动相添加剂。当[HMIM][BF_4]浓度为16 mmol/L,流动相pH值为3.0,甲醇比例为37%时,钩藤碱和异钩藤碱能够实现基线分离,满足样品分离测定的需求。     

烷基磺酸阴离子无卤素离子液体的物理化学性质研究(英文)

通过一步法合成了基于1,3-二烷基咪唑阳离子和甲烷磺酸或对甲苯磺酸阴离子的无卤素离子液体,并对它们的物理化学性质如聚集行为、表面性质、热性质、密度、黏度、折光率和电化学性质等进行了详细研究.结果表明在甲烷磺酸阴离子基离子液体中观察到离子液体中普遍存在的离子簇行为;同等条件下[BEim]MS的荧光光谱强度较[BEim]TS弱;[C12Mim]MS展现出液晶行为;[TS]-基离子液体有着较高的折光率,大于1.51.     

离子液体中卤素离子杂质的离子色谱-直接电导检测法分析

研究了离子色谱-直接电导检测法分离测定离子液体中的卤素离子(F~-、Cl~-、Br~-)杂质.采用Shim-pack IC-A3阴离子交换色谱柱,考察了淋洗液种类及浓度、流速和色谱柱温度对分离测定的影响.最佳色谱条件为:以1.25 mmol/L邻苯二甲酸氢钾为淋洗液,流速1.5 mL/min,色谱柱温45 ℃.在此条件下可以基线分离卤素离子,且NO~-_3、BF~-_4、SO~(2-)_4不干扰测定.该法测定卤素离子的检出限(S/N=3)为0.02 ～0.11 mg/L,峰面积的相对标准偏差(n=5)不大于0.7%,F~-、Cl~- 和Br~- 的标准曲线的线性范围分别为0.1 ～50、0.1 ～50、0.5 ～100 mg/L.将方法用于烷基咪唑四氟硼酸盐离子液体中卤素离子杂质的测定,加标回收率为98% ～102%.     

PVC固载亲水性离子液体选择性分离血红蛋白研究

将N-甲基咪唑嫁接到聚氯乙烯(PVC)链上制备了亲水性离子液体1-乙烯基-3-甲基咪唑氯代盐-PVC复合物, 并用红外光谱、核磁共振氢谱和表面电荷分析对其进行了表征, 咪唑基团对氯乙烯基中氯的取代率为2.8%. 蛋白质吸附研究表明, 在特定条件下该固载型离子液体对血红蛋白具有吸附选择性, 据此建立了固相萃取分离血红蛋白的方法. 考察了吸附时间、离子强度、洗脱剂及其浓度等对分离纯化效率的影响. 在最优实验条件下, 该固载型离子液体-PVC复合物对30μg•mL^-1血红蛋白的吸附效率为91%, 洗脱效率为75%, 吸附容量为22.7μg•mg^-1. 用1.0% (m/V) SDS洗脱后血红蛋白活性约为原始溶液中的71%. SDS-PAGE凝胶电泳证明其有效地从人全血样品中分离出纯度较高的血红蛋白.     

离子液体表面活性剂1-丁基-3-甲基咪唑烷基硫酸酯的合成及其在水溶液中的聚集行为

采用离子交换法,由1-丁基-3甲基咪唑氯盐（C4mimCl）和烷基硫酸钠合成了一系列无卤素的阴离子表面活性离子液体—1-丁基-3-甲基咪唑烷基硫酸酯[C4mim][CnH2n 1SO4](n=8,12,16),利用表面张力仪、稳态荧光光谱等手段考察了表面活性离子液体在水溶液表面及体相中的聚集行为,结果表明,与传统无机反离子相比,有机咪唑阳离子[C4mim] 作为反离子的离子液体型表面活性剂具有较高的表面活性,[C4mim] 产生的氢键引起的抑制分子规则排列的作用小于其促进分子有序排列的疏水作用。长烷基链的阴离子是界面膜及胶束的主要组成成分,阴离子疏水烷基碳链的增长虽然可促进胶束的形成,但却在一定程度上抑制[C4mim] 离子参与界面或胶束的形成;阴离子所带烷基链越长,越不利于阳离子[C4mim]＋参与界面膜或胶束的形成,界面膜或胶束中表面活性剂排布越松散,即界面张力越大,体系中胶束聚集数较小。     

咪唑六氟磷酸盐聚离子液体凝胶电解质的辐射合成及性能研究

以1-乙烯基-3-烷基咪唑六氟磷酸盐C_nvimPF_6(n=6,12)为单体,(1,6-亚己基)-双(3-乙烯基咪唑)六氟磷酸盐为交联剂,六氟磷酸锂为添加剂,混合碳酸酯为溶剂,采用辐射引发聚合、交联合成了新型的聚离子液体凝胶电解质(简称PC_nvimPF_6-Li GPE),并研究了离子液体单体侧链长度、单体浓度、交联剂含量对PC_nvimPF_6-Li GPE性能的影响.结果表明所合成的PC_nvimPF_6-Li GPE具有良好的力学性能和高离子电导率,最大离子电导率可达7.18 mS/cm.     

N-羧基吡啶功能化离子液体的表征

合成了系列新型N-羧基吡啶功能化离子液体, 利用1H NMR、13C NMR、IR、DSC对其进行表征并研究了其与常规溶剂的相溶性, 采用酸碱滴定法测量了系列离子液体的酸离解常数pKa值. N-羧基取代吡啶功能化离子液体的pKa值在2.5~4.0之间, 并随阳离子取代羧基碳链的增长而增大; 离子之间形成氢键及阴、阳离子的大小是影响离子液体熔点的主要因素. 阴离子越小, 熔点越高. 所合成的N-羧基吡啶功能化离子液体具有相同的相溶性且由取代羧基所决定, 与常见烷基咪唑离子液体相比, N-羧基吡啶功能化离子液体与丙酮、二氯甲烷并不相溶. 功能化离子液体的阳离子取代基是影响其物化性能的主要因素, 通过改变功能化基团碳链的长短及与不同阴离子进行组合, 可以对功能化离子液体物理、化学性能进行调节.     

离子液体作高效液相色谱流动相添加剂测定水杨酸

建立了以离子液体作反相高效液相色谱流动相添加剂测定水杨酸的方法.实验以ZORBAX ODS反相色谱柱为分离柱,采用紫外检测方法,研究了检测波长、离子液体烷基链长度、离子液体溶液的浓度以及pH值等对分离和测定的影响.优化的色谱条件为:以体积比60:40的甲醇-3.0 mmol/L1-丁基-3-甲基咪唑四氟硼酸盐溶液(乙酸...     

离子液体表面活性剂烷基硫酸1-丁基-3-甲基咪唑鎓盐的合成及其在水溶液中的聚集行为

采用离子交换法,由氯化1-丁基-3-甲基咪唑鎓(C_4mimCl)和烷基硫酸钠合成了一系列无卤素的阴离子表面活性离子液体—烷基硫酸1-丁基-3-甲基咪唑鎓盐[C_4mim][C_nH_(2n+1)SO_4](n=8,12,16),利用表面张力仪、稳态荧光光谱等手段考察了表面活性离子液体在水溶液表面及体相中的聚集行为。结果表明,与传统无机反离子相比,有机咪唑阳离子[C_4mim]~+作为反离子的离子液体型表面活性剂具有较高的表面活性,[C_4mim]~+产生的氢键引起的抑制分子规则排列的作用小于其促进分子有序排列的疏水作用。长烷基链的阴离子是界面膜及胶束的主要组成成分,阴离子疏水烷基碳链的增长虽然可促进胶束的形成,但却在一定程度上抑制[C_4mim]~+参与界面或胶束的形成;阴离子所带烷基链越长,越不利于阳离子[C_4mim]~+参与界面膜或胶束的形成,界面膜或胶束中表面活性剂排布越松散,即界面张力越大,体系中胶束聚集数较小。     

室温离子液体在过渡金属催化反应中的应用研究进展

室温离子液体(RTILs)是在室温或近于室温下呈液态的由离子构成的盐类．如图1所示，RTILs按阳离子类型可以分为4类：烷基季铵盐离子；烷基季鳞盐离子；N，N-二烷基咪唑离子和N-烷基吡啶离子．按阴离子可分为：氯化盐 AlX3(X=卤素)和含有RF1^-,PF6^-等阴离子的离子液体．     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.