介孔硅铝酸盐的合成及其在傅克反应中的催化性能

采用溶胶凝胶法合成了一系列有序性好且酸性较强的介孔硅铝酸盐材料。利用X射线粉末衍射(XRD)、透射电镜(TEM)、27Al核磁共振(27Al NMR)、氨气程序升温脱附(HN3-TPD)及吡啶吸附红外光谱(Py-FT-IR)对制备的介孔硅铝酸盐材料的结构和性能进行表征,并考察了材料在苯甲醚和苯甲醇的傅克烷基化反应中的催化活性。实验结果表明:合成过程中,表面活性剂的用量、硅铝物质的量之比会影响材料结构的有序性,醋酸用量对材料结构有序性影响很小;进一步研究结果表明,nSi/nAl比会影响材料的酸催化活性,当nSi/nAl=10时材料的酸催化活性最高。氨气程序升温脱附和吡啶吸附红外光谱表明nSi/nAl=10的材料含有最多的B酸酸量。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂, 应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明, 酸处理NaY分子筛后, 骨架铝被脱除, 导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔, 有利于产物分子的扩散, 从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能, DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂,应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明,酸处理NaY分子筛后,骨架铝被脱除,导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔,有利于产物分子的扩散,从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能,DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

立方介孔相含钕氧化硅的合成与表征

以十六烷基三甲基溴化铵为结构导向剂，通过水热法合成了具有立方结构的含钕Nd-MCM-48介孔分子筛材料。XRD和TEM测试表明当n_Nd/n_Si<0.05时可以获得典型的长程有序介孔立方结构相，随n_Nd/n_Si比的增加，晶胞参数的增大和红外吸收光谱(FT-IR)的变化为Nd进入介孔分子筛骨架中提供了有力证据。N₂吸附-脱附实验给出了其BET表面积为1 195 m²·g^-1，BJH平均孔径为3.6 nm。紫外-可见漫反射光谱(UV-Vis)证明钕氧形成一种八面体结构。X射线光电子能谱(XPS)进一步证明钕主要以三价形式存在于立方介孔分子筛骨架中。     

高酸位多级孔超稳Y型沸石的制备及催化性能

以表面活性剂十六烷基三甲基溴化铵(CTABr)为模板剂,在水热体系对水蒸气处理后的超稳Y型(USY)沸石进行晶化处理,获得高酸量和高水热稳定性的USY-c-w样品。利用X射线衍射、扫描电子显微镜、透射电子显微镜、固态核磁共振、N₂吸附-脱附、NH₃-程序升温脱附、傅里叶变换红外光谱及吡啶红外对所制备催化剂的物化性质进行详细表征。选用1,3,5-三异丙苯(TIPB)催化裂化作为探针反应,研究制备的催化剂的催化性能,并与工业USY沸石进行对比。结果表明,再次水热晶化后,样品的硅铝骨架局部重构,非骨架铝重新进入沸石骨架,合成样品的硅铝比(n_Si/n_Al)由10降至3.0;再晶化后的USY沸石,不仅具有丰富的介孔结构,并且具有更多的弱酸和中强酸位点。在TIPB裂解反应中,再晶化后的USY沸石表现出比原样品更优异的催化性能。     

铝/氟比对改性尖晶石锰酸锂性能的影响

采用草酸铝、氟化锂与尖晶石LiMn₂O₄进行高温固相反应，制备出改性尖晶石LiMn₂O₄材料。对材料进行了XRD、SEM分析及电性能测试，结果表明，改性材料均基本保持了尖晶石主体结构，晶格常数随n(Al)∶n(F)比例的增大而减小;Al³⁺、F^-的引入可以引起材料颗粒表面形貌的变化，产生规则结晶，而颗粒表面结晶的大小受n(Al)∶相似文献   

一种合成高水热稳定性微孔-介孔复合分子筛β沸石/MCM-41的新方法

首次以β沸石作为硅铝源制备了β沸石/MCM-41微孔-介孔复合分子筛材料，通过XRD、IR、N₂吸附脱附、SEM和水热处理等手段对复合材料进行了表征，并与MCM-41和β沸石及二者的机械混合物的有关性能进行了对比研究。结果表明，复合分子筛明显不同于机械混合物，其水热稳定性远远高于普通方法合成的介孔分子筛，而且发现通过改变体系的n_Na/n_Si比，可以调变复合样品中的微孔、介孔相的相对含量。     

WxC-MCM-48催化剂的合成、表征及加氢脱硫催化性能

以正硅酸乙酯(TEOS)为硅源，十六烷基三甲基溴化铵(CTAB)为表面活性剂，仲钨酸铵为钨源，采用水热晶化法一步合成了不同钨含量(以Si、W物质的量比n_Si/n_W表示)的WO₃-MCM-48，然后经甲烷/氢气(V/V=1/4)混和气体程序升温还原碳化(TPC)，制备出了W_xC-MCM-48(x=1、2)催化剂，采用XRD、N₂吸附-脱附和NH₃-TPD对样品的结构进行了表征，用噻吩作为模型化合物，对W_xC-MCM-48催化剂的加氢脱硫催化活性进行了评价。结果表明，在一定钨含量的条件下，WO₃-MCM-48和W_xC-MCM-48样品仍然保持MCM-48的三维立方有序介孔结构，n_Si/n_W=30～15时，碳化钨的物相为W₂C；n_Si/n_W=7.5时，碳化钨为W₂C和WC物相，W_xC-MCM-48催化剂表现出了良好的加氢脱硫催化性能。     

高酸位多级孔超稳Y型沸石的制备及催化性能

以表面活性剂十六烷基三甲基溴化铵（CTABr）为模板剂,在水热体系对水蒸气处理后的超稳Y型（USY）沸石进行晶化处理,获得高酸量和高水热稳定性的USY-c-w样品。利用X射线衍射、扫描电子显微镜、透射电子显微镜、固态核磁共振、N₂吸附-脱附、NH₃-程序升温脱附、傅里叶变换红外光谱及吡啶红外对所制备催化剂的物化性质进行详细表征。选用1,3,5-三异丙苯（TIPB）催化裂化作为探针反应,研究制备的催化剂的催化性能,并与工业USY沸石进行对比。结果表明,再次水热晶化后,样品的硅铝骨架局部重构,非骨架铝重新进入沸石骨架,合成样品的硅铝比（n_SiO2/n_Al2O3）由10降至3.0;再晶化后的USY沸石,不仅具有丰富的介孔结构,并且具有更多的弱酸和中强酸位点。在TIPB裂解反应中,再晶化后的USY沸石表现出比原样品更优异的催化性能。     

Pt-Al/MCM-41催化剂的制备及催化合成有机硅增效剂

以介孔硅MCM-41为载体,AlCl₃为促进剂,制备了负载型Pt-Al/MCM-41催化剂。利用傅里叶红外光谱（FTIR）、N₂吸附-脱附、X射线衍射（XRD）、透射电子显微镜（TEM）、X射线光电子能谱（XPS）、电感耦合等离子体发射光谱（ICP）对催化剂的结构、形貌以及金属间作用力进行了表征,着重探讨了不同Al加入量对催化剂结构和金属间作用力的影响,系统考察了Pt-Al/MCM-41用于催化聚乙二醇烯丙基醚和七甲基三硅氧烷合成有机硅增效剂。结果表明,Al的加入量对催化剂的结构和有序度有一定的影响,其比表面积、孔容和有序度随着Al用量的增加而逐步降低。此外,加入一定量的Al有利于提高Pt晶粒的分散度,减小其粒径。Pt₁Al₂/MCM-41催化剂具有良好的重复使用性,使用6次无明显失活,其转化率仍大于90%。合成有机硅增效剂的最佳工艺为：n_PGAE/n_MD^HM=1.1,反应时间为4 h,反应温度为100℃,催化剂用量为0.5%,其转化率达94.1%。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.