影响热还原氧化石墨烯超级电容器性能的因素比较

通过改进的Hummer法制得氧化石墨烯,并在不同温度的氩气气氛中还原得到一系列热还原氧化石墨烯（T-RGO）. 电化学测试表明,T-RGO作为超级电容器电极材料时,良好的导电性是必需的,但石墨烯表面含氧官能团对其电容性能的影响要远大于导电性和比表面积的影响,900 °C还原的T-RGO比表面积为314 m²·g^-1电导率为2421 S·m^-1,但其容量只有56 F·g^-1,然而300 °C还原的T-RGO比表面积为18.8 m²·g^-1电导率为574 S·m^-1,其容量却达到281 F·g^-1. 材料表征分析表明,300 °C 还原的石墨烯之所以有更高的电容,是因为除双电层电容外,更多的是由其表面含氧官能团提供的赝电容,这使作者以后在设计制备超级电容器等储能设备用石墨烯基电极材料时更加有针对性.     

基于过渡金属硫化物/还原氧化石墨烯复合物的高性能超级电容器

组装高能量密度的非对称超级电容器需要使用比电容大、 体积变化小且循环稳定性好的电极材料. 过渡金属硫化物(TMSs)与纳米碳材料的复合物是此类电极材料之一. 采用水热法合成了由Cu-Mo硫化物在微波剥离的还原氧化石墨烯表面生长的复合材料(CuS-MoS₂/MErGO). 此复合材料在电流密度为2 A/g时具有高达861.5 F/g的比电容和良好的循环稳定性. 将1.6 V的电池电压施加在由NiS/MErGO为正极, CuS-MoS₂/MErGO为负极组装成的不对称超级电容器上时, 该电容器的功率密度为1.28 kW/kg, 且能量密度保持为54.2 W·h·kg^-1. 结果表明, TMS复合材料是一种很有前途的高性能电化学储能材料, 尤其是用于非对称超级电容器的组装.     

α-Fe2O3/石墨烯水凝胶复合材料的自组装制备及电化学性能

采用水热法自组装合成超薄α-Fe₂O₃/还原氧化石墨烯水凝胶（3DGH）复合材料.复合材料的物性表征和电化学测试结果表明,α-Fe₂O₃/3DGH材料呈三维多孔结构,直径约100 nm的α-Fe₂O₃颗粒均匀生长在还原氧化石墨烯片层上;通过调节复合材料中Fe³⁺的负载量,可实现α-Fe₂O₃颗粒的可控生长,粒径为200~30 nm;作为超级电容器的电极材料,α-Fe₂O₃粒径为100 nm左右时,铁负载量为40%的α-Fe₂O₃/3DGH复合材料具有最大的比电容（750.8 F/g,1 A/g）和循环稳定性（在10 A/g电流密度下,充放电5000次后比电容保持率为81.9%）,高于纯α-Fe₂O₃材料的比电容（251.6 F/g,1 A/g）和循环稳定性（充放电5000次后比电容保持率为43.8%）.     

三维还原氧化石墨烯/聚苯胺复合材料的制备及其超级电容性能

以制备的氧化石墨凝胶和聚苯胺纳米线为原料, 将二者按一定的质量比进行混合超声分散, 再以混合分散液为前驱体采用一步水热法制备得到三维还原氧化石墨烯(RGO)/聚苯胺(PANI) (RGP)复合材料, 采用扫描电镜(SEM), 透射电镜(TEM), X射线衍射(XRD), 傅里叶变换红外(FT-IR)光谱, X射线光电子能谱(XPS)和电化学测试等分析研究了复合材料的形貌、结构和超级电容性能. 结果表明, 复合材料既保持了还原氧化石墨烯的基本形貌, 又能使聚苯胺较好地镶嵌在还原氧化石墨烯的网状结构中; 且当氧化石墨与聚苯胺的质量比为1:1时复合材料在0.5 A·g^-1电流密度下比电容可高达758 F·g^-1, 即使在大电流密度(30 A·g^-1)下其比容量仍高达400 F·g^-1,在1A·g^-1电流密度下循环1000次后比容量保持率为86%, 表现出了良好的倍率性能和循环稳定性, 其超级电容性能远优于单纯的还原氧化石墨烯和聚苯胺, 其优异的超级电容性能可归咎于二者的相互协同作用.     

氢氧化镍纳米线/三维石墨烯复合材料的制备及其电化学性能

采用水热法制备了氢氧化镍纳米线/三维石墨烯复合材料及作为比较的三维石墨烯、氢氧化镍纳米线、还原氧化石墨烯和氢氧化镍纳米线/还原氧化石墨烯, 通过X射线衍射、扫描电镜、热失重分析和氮气吸脱附表征了材料的形貌、结构和组成, 并采用循环伏安法和恒电流充放电测试了复合材料的电化学性能. 结果表明: 氢氧化镍纳米线/三维石墨烯复合材料中直径为20-30 nm的氢氧化镍纳米线和三维结构的石墨烯紧密结合, 相互交联形成网状结构, 其比表面积达到136 m²·g^-1, 孔径分布20-50 nm, 氢氧化镍纳米线的含量达到88% (w,质量分数). 在6 mol·L^-1的KOH电解液中, 复合材料的比电容在1 A·g^-1电流密度下达到1664 F·g^-1, 在1 A·g^-1电流密度下循环3000 次后的比电容保持率为93%. 将复合材料的比电容和循环性能与氢氧化镍纳米线、氢氧化镍纳米线/还原氧化石墨烯、三维石墨烯和还原氧化石墨烯的性能进行比较, 发现三维石墨烯较还原氧化石墨烯具有更高的比表面积和三维多孔结构, 可以更大地提高活性物质的利用率, 进而提高复合材料的比电容和稳定性.     

硫化镍/三维网络石墨烯复合材料制备及其在高性能超级电容器的应用研究

本文在泡沫镍上生长三维网络状结构的石墨烯（3DG）,以此为模板合成石墨烯复合电极并将其应用于超级电容器. 采用一步水热法在3DG上合成得到Ni₃S₂纳米棒结构（Ni₃S₂/3DG）. 通过TEM、XRD、SEM和拉曼光谱等手段表征对Ni₃S₂/3DG复合材料的形态与结构进行表征. 电化学测试表明,Ni₃S₂/3DG复合材料具有高的比电容（在扫速为5 mV·s^-1下,具有1825.3 F·g^-1的比容量）和放电电容（在电流密度10 mA下电容高达516.7 F·g^-1）. 此外,在电流密度20 mA下具有良好的循环性能（循环1000周后仍能保留约100%的初始电容）. 本工作为得到高能量密度和良好的长期稳定性的复合材料提供了参考.     

具有高效电化学储能的中空网状笼还原氧化石墨烯

通过ZnO模板辅助电沉积法制备了中空网状笼还原氧化石墨烯,具有纳米管、多孔结构、网状结构和3D微米中空笼等多层次架构. 这样的结构能够同时促进电化学活性物种的传输,提高电极材料的利用率,以及提升超级电容器性能. 该类中空网状笼还原氧化石墨烯做超级充电器电极材料时表现出了优良的电化学性能,研究结果显示,在1.0 A•g^-1时比电容达到393 F•g^-1. 而且当电流密度从1.0 A•g^-1增加到20 A•g^-1,电容仅衰减了21.2%,10000周循环后比电容损失小于1%,表明具有优异的电容稳定性.     

纳米纤维素/还原氧化石墨烯复合材料用于高性能超级电容器

以高浓度氧化石墨烯(GO)溶液作为反应前驱体,纳米纤维素(NC)作为物理间隔物和电解液储存器,通过简单的一步水热法制备了纳米纤维素/还原氧化石墨烯(NC/rGO)复合材料,并探究了其作为超级电容器电极材料的潜力。结果如下：NC添加量为1 mL所制备的NC/rGO-1具有最佳电化学性能。基于NC/rGO-1的无黏合剂对称型超级电容器在0.3 A·g^-1的电流密度下显示出了269.33 F·g^-1和350.13 F·cm^-3的高质量和体积比电容,并在10.0 A·g^-1时仍能达到215.88 F·g^-1和280.62 F·cm^-3(其初始值的80.15%)。组装器件还显示出了较高的质量和体积能量密度(9.3 Wh·kg^-1和12.13 Wh·L^-1)和出色的循环性能(10 A·g^-1下10 000次循环后其初始比电容仅减少6.02%)。     

Mn3O4/石墨烯复合材料的制备与电化学性能研究

本文以氧化石墨烯（GO）溶液为氧化剂,采用水热法使GO直接氧化Mn(Ac)₂制备Mn₃O₄/石墨烯复合材料,并通过在制备过程中加入氨水提高了复合材料中GO的还原程度与Mn₃O₄颗粒的分散性. 制得的Mn₃O₄/石墨烯复合材料表现出优异的电化学性能. 在0.5 A·g^-1的电流密度下复合材料质量比容量可达到850 mAh·g^-1,0.5 A·g^-1时充放电循环测试200周容量保持率为99%.     

水热法制备Fe3O4/rGO纳米复合物作为锂离子电池阳极材料

以氢氧化铁为四氧化三铁的前驱体,氧化石墨烯（GO）为还原石墨烯（rGO）的前驱体,以水合肼和二水合柠檬酸三钠为混合还原剂,采用水热法制备了还原石墨烯负载四氧化三铁纳米颗粒（Fe₃O₄/rGO）的复合材料。通过透射电子显微镜（TEM）、X-射线衍射（XRD）和热重分析（TGA）对产物的形貌、结构和组成进行了表征。以锂片为对电极进行了扣式电池的组装,通过恒电流充放电和循环伏安法对其电化学性能进行了测试。材料具有均一的形貌,rGO具有较高的还原程度且可以在充放电过程中缓冲Fe₃O₄纳米颗粒的体积变化,使得Fe₃O₄/rGO纳米复合物具有较好的电化学性能。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.