α-Fe2O3/石墨烯水凝胶复合材料的自组装制备及电化学性能

采用水热法自组装合成超薄α-Fe₂O₃/还原氧化石墨烯水凝胶（3DGH）复合材料.复合材料的物性表征和电化学测试结果表明,α-Fe₂O₃/3DGH材料呈三维多孔结构,直径约100 nm的α-Fe₂O₃颗粒均匀生长在还原氧化石墨烯片层上;通过调节复合材料中Fe³⁺的负载量,可实现α-Fe₂O₃颗粒的可控生长,粒径为200~30 nm;作为超级电容器的电极材料,α-Fe₂O₃粒径为100 nm左右时,铁负载量为40%的α-Fe₂O₃/3DGH复合材料具有最大的比电容（750.8 F/g,1 A/g）和循环稳定性（在10 A/g电流密度下,充放电5000次后比电容保持率为81.9%）,高于纯α-Fe₂O₃材料的比电容（251.6 F/g,1 A/g）和循环稳定性（充放电5000次后比电容保持率为43.8%）.     

BC/CoNi2S4@PPy柔性复合电极材料的制备及电化学性能

本文采用溶剂热、原位聚合和真空抽滤相结合的方法制备了用于超级电容器的细菌纤维素/镍钴硫化物/聚吡咯(BC/CoNi₂S₄@PPy)柔性电极材料,通过X射线衍射、场发射扫描电镜、红外光谱、氮气吸脱附、拉伸强度和接触角表征了材料的形貌结构、组成、机械性能和亲水性,并采用循环伏安法和恒电流充放电测试了复合材料的电化学性能。结果表明,表面含氧官能团丰富的BC纤维网络结构对氧化还原活性物质CoNi₂S₄的生长和导电聚合物PPy的分布具有引导作用,CoNi₂S₄均匀分布在BC网络中,且PPy均匀包覆在BC纤维和CoNi₂S₄纳米球表面构成具有丰富孔隙结构的三维导电网络,使得该复合材料具有较好的机械性(抗拉强度达28.0±0.1 MPa)、亲水性(对6 mol·L^-1 KOH的瞬间接触角为43.6°)及良好的导电性。该电极材料在1 A·g^-1下比电容高达2670 F·g^-1,充放电循环10000次后比电容的保持率为82.73%,且经1000次反复弯曲后电化学性能保持不变。此外,将其与活性炭组成的非对称超级电容器,在1 A·g^-1下比电容为1428 F·g^-1,最高能量密度和功率密度分别达49.8 Wh·kg^-1和741.8 W·kg^-1。     

泡沫镍负载NiMoO4/NiMoS4复合材料的制备及其电化学性能

以泡沫镍作为基底,采用水热法原位生长出具有片状结构的NiMoO₄活性材料,然后通过水热硫化制备出NiMoO₄/NiMoS₄复合材料,研究了水热时间和硫脲添加量对样品形貌和电化学性能的影响。电化学结果表明,NiMoO₄/NiMoS₄电极在电流密度为1A·g^-1时,比电容为1560.7F·g^-1,在电流密度为40A·g^-1时循环2000次后,比电容仍为初始比电容的76.7%。将NiMoO₄/NiMoS₄电极材料与活性炭(AC)分别作为正、负极组装的非对称超级电容器(ASC)在400W·kg^-1的功率密度下可提供29.0Wh·kg^-1的能量密度。     

CoNi2S4上电沉积NiS用于柔性固态非对称超级电容器

采用一种在CoNi2S4上电沉积NiS的有效方法来改善钴/镍硫化物的性能。CoNi2S4@NiS电极材料在1 A·g^-1时比电容达到1433 F·g^-1,并具有很好的倍率性能。CoNi2S4@NiS和还原氧化石墨烯组装成的柔性固态非对称超级电容器的能量密度在功率密度为800 W·kg^-1时达到36.6 Wh·kg^-1,并且在10000次充放电后表现出良好的循环性能,循环保持率达87.8%。     

微波辅助合成具有优异电化学性能的rGO/CeO2超级电容器电极材料

CeO₂具有良好的赝电容, 但有关碳/CeO₂复合材料的电化学性能有待改善. 本工作采用简单的微波辅助合成法, 将氧化石墨烯与Ce(NO₃)₃混合发生氧化还原反应, 获得还原氧化石墨烯(rGO)/CeO₂复合材料. 通过形貌观察, CeO₂以颗粒形式均匀分布在褶皱的rGO上, 且沿着rGO表面仿形生长; 纳米级CeO₂颗粒之间存在微小间隙. N₂吸/脱附测试结果表明, rGO/CeO₂具有大的比表面积和介孔孔径, 有益于与电解液充分接触. 通过电化学测试, rGO/CeO₂的比电容高达468 F•g^-1, 经过10000次充放电循环, 电容保持率高达107.3%. 优异的循环稳定性归因于大表面积的rGO与均匀薄层的CeO₂良好的协同效应减少了离子传输的阻力以及CeO₂颗粒之间微小的间隙, 缓解了Ce⁴⁺还原为Ce³⁺过程中发生的晶格膨胀. 将rGO/CeO₂组装成对称型超级电容器rGO/CeO₂||rGO/CeO₂获得的能量密度达18.16 Wh•kg^-1. rGO/CeO₂作为超级电容器电极材料具有广阔前景.     

聚苯胺/介孔碳纳米线复合电极材料的制备和性能

以介孔碳纳米线为基体, 通过电化学方法制备了新型聚苯胺/介孔碳纳米线(PANI/MCFs)复合材料, 采用SEM和TEM等手段对样品的结构和形貌进行了表征. 结果表明, 聚苯胺均匀附在介孔碳纳米线表面, 并填充到纳米线介孔孔道中. 将复合材料组装成三电极体系超级电容器, 用循环伏安、 恒流充放电和交流阻抗等方法对材料的电化学性能进行了测试. 结果显示, 在1 mol/L H₂SO₄溶液中, 复合材料的比电容达到391 F/g, 其循环稳定性也得到显著提高.     

NiS2纳米片的制备及其在非对称超级电容器中的应用

本文采用牺牲模板法,以Ni(OH)₂作为前驱体制备NiS₂. 通过对NiS₂进行XRD、EDS、BET、SEM及TEM等表征来研究NiS₂的元素组成及结构形貌. SEM及TEM结果显示前驱体及NiS₂均为纳米片结构. 电化学测试结果表明NiS₂存在着优秀的电容性能,在电流密度为1 A·g^-1时,NiS₂比电容能够达到1067.3 F·g^-1,同时具有高的倍率特性. 为了进一步探究NiS₂作为电活性材料的实用性,以NiS₂作为阳极材料,活性炭（AC）作为阴极组装成非对称超级电容器,在功率密度为0.8 kW·kg^-1,能量密度高达38.4 Wh·kg^-1,并且在3000次恒流充放电后,比电容依然保持93.7%.     

Ni(OH)2修饰的三聚氰胺泡沫用于可压缩超级电容器电极

通过化学镀和电化学镀的方法制备了一种Ni(OH)₂电化学活性材料修饰三聚氰胺泡沫(MF)可压缩骨架的超级电容器电极材料MF/Ni(OH)₂。MF/Ni(OH)₂可压缩电极材料表现出最佳的电容性能,例如循环稳定性(即使在40 mA/cm^-3的电流密度下经过2000次充放电循环后,可压缩电极仍能保持90.63%的初始电容)和可压缩稳定性(即使在压缩率为50%时,仍具有97.88%的电容保持率)。层状可压缩超级电容器由MF/Ni(OH)₂弹性材料作为阳极,镍/碳(Ni/C)为阴极以及实验室中常用的滤纸作隔膜材料组成。这种超级电容器装置在不同的压缩下表现出良好的电化学性能和优异的压缩稳定性。最后,使用可压缩的超级电容器来点亮LED灯,以展示其在柔性电子设备中的应用。这些优化的电化学和机械性能表明MF/Ni(OH)₂可作为可压缩超级电容器的应用中的候选电极。     

WO3/碳布柔性非对称超级电容器的组装及性能研究

以超级电容器的电极材料制备、性质研究及对组装的非对称超级电容器的性能研究为核心内容,提高超级电容器电化学性能为主要目的,采用水热合成法在碳布基底上合成三氧化钨/碳布和活化后的碳布为超级电容器的电极材料。采用SEM、XRD表征方法对制备的材料进行了形貌表征及物相分析;使用上海辰华电化学工作站对电极材料进行了循环伏安、恒流充放电、交流阻抗等电化学性能测试. 最终得到以三氧化钨/碳布为正极材料、活化后的碳布为负极材料组装成不对称柔性电容器,进行电化学测试,其电位窗口提高到0~1.6 V,电流密度61.9 mA·cm^-2时,电容达到58.96 F·cm-2,功率密度0.48 W·cm^-2时,能量密度为20.36 mWh·cm^-2,同时在电流密度8 mA·cm^-2时,循环3000次时表现出良好的循环性能,相较于对称型超级电容器,倍率性能更加优异.     

基于玉米秸秆合成的多孔生物质炭材料及其电化学储能

以玉米秸秆为原料,合成了高比表面积(2167 m²/g)的多孔生物质炭材料。 优化实验条件即可获得性能最佳的生物质炭电极材料,其在电流密度为1 A/g时的比电容高达390 F/g。 更重要的是,以所得最佳多孔生物质炭为电极材料,3 mol/L 的KOH溶液为电解质,组装了液相对称超级电容器。 该超级电容器在功率密度为818 W/kg时,其能量密度高达7 Wh/kg,在循环10000圈后的电容保持率为91.1%。 同时,将两个这种超级电容器串联充电之后,能够点亮15个LED灯并驱动小风扇正常工作。 这些结果表明,将基于玉米秸秆的多孔生物质炭作为先进电极材料应用于超级电容器具有较大的实际应用价值。     

High performance hybrid supercapacitor based on hierarchical MoS2/Ni3S2 metal chalcogenide

Herein, we synthesized hierarchical MoS₂/Ni₃S₂ structures as electrode materials grown on nickel foam by a facile hydrothermal strategy. The hierarchical MoS₂/Ni₃S₂ structures show high specific capacitance.     

Ni3S2@碳纳米管复合材料的制备及其储钠性能

采用一步固相煅烧工艺制备了碳纳米管原位封装Ni₃S₂纳米颗粒（Ni₃S₂@CNT）,并研究了其作为钠离子电池（SIBs）负极材料的电化学性能. 通过X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、循环伏安测试、恒流充放电以及交流阻抗等研究了Ni₃S₂@CNT的物相结构、形貌特征以及电化学性能. 电化学测试表明,材料在100 mA·g ^-1电流密度下,放电容量可以达到541.6 mAh·g ^-1,甚至在2000 mA·g ^-1的大电流密度下其放电比容量也可以维持在274.5 mAh·g ^-1. 另外,材料在100 mA·g ^-1电流密度下,经过120周充放电循环后其放电和充电比容量仍然可以保持在374.5 mAh·g ^-1和359.3 mAh·g ^-1,说明其具有良好倍率性能和循环稳定性能. 良好的电化学性能归因于这种独特的碳纳米管原位封装Ni₃S₂纳米颗粒结构. 碳纳米管不但可以提高复合材料的导电性,也可以缓冲Ni₃S₂纳米颗粒在反复充放电过程中产生的体积膨胀效应,明显改善了Ni₃S₂@CNT负极复合材料的电化学性能.     

Design and Preparation of Graphene/Fe2O3 Nanocomposite as Negative Material for Supercapacitor

The development of high specific capacitance electrode materials with high efficiency, scalability and economic feasibility is significant for the application of supercapacitors, however, the synthesis of electrode material still faces huge challenges. Herein, graphene(G)/Fe₂O₃ nanocomposite was prepared via a simple hydrothermal method connected with subsequent thermal reduction process. Scanning electron microscopy(SEM) and transmission electron microscopy(TEM) results showed rod-like Fe₂O₃ nanoparticles were prepared and well-dispersed on graphene layers, providing a rich active site and effectively buffering the aggregation of Fe₂O₃ nanoparticles in the process of electrochemical reaction. The specific capacitance of the obtained G/Fe₂O₃ nanocomposite as negative electrode for supercapacitor was 378.7 F/g at the current density of 1.5 A/g, and the specific capacitance retention was 88.76% after 3000 cycles. Furthermore, the asymmetric supercapacitor(ASC) was fabricated with G/Fe₂O₃ nanocomposite as negative electrode, graphene as positive electrode, which achieved a high energy density of 64.09 W∙h/kg at a power density of 800.01 W/kg, maintained 30.07 W∙h/kg at a power density of 8004.89 W/kg, and retained its initial capacitance by 78.04% after 3000 cycles. The excellent result offered a promising way for the G/Fe₂O₃ nanocomposite to be applied in high energy density storage systems.     

Phenylenediamine-formaldehyde chemistry derived N-doped hollow carbon spheres for high-energy-density supercapacitors

Porous carbon spheres represent an ideal family of electrode materials forsupercapacitors because of the high surface area,ideal conductivity,negligible aggregation,and ability to achieve space efficient packing.However,the development of new synthetic methods towards porous carbon spheres still remains a great challenge.Herein,N-doped hollow carbon spheres with an ultrahigh surface area of2044 m²/g have been designed based on the phenylenediamine-formaldehyde chemistry.When applied in symmetric supercapacitors with ionic electrolyte(EMIBF_4),the obtained N-doped hollow carbon spheres demonstrate a high capacitance of 234 F/g,affording an ultrahigh energy density of 114.8 Wh/kg.Excellent cycling stability has also been achieved.The impressive capacitive performances make the phenylenediamine-formaldehyde resin derived N-doped carbon a promising candidate electrode material for supercapacitors.     

基于NiCo2O4纳米片电极的非对称混合电容器

The looming global energy crisis and ever-increasing energy demands have catalyzed the development of renewable energy storage systems. In this regard, supercapacitors (SCs) have attracted widespread attention because of their advantageous attributes such as high power density, excellent cycle stability, and environmental friendliness. However, SCs exhibit low energy density and it is important to optimize electrode materials to improve the overall performance of these devices. Among the various electrode materials available, spinel nickel cobaltate (NiCo₂O₄) is particularly interesting because of its excellent theoretical capacitance. Based on the understanding that the performances of the electrode materials strongly depend on their morphologies and structures, in this study, we successfully synthesized NiCo₂O₄ nanosheets on Ni foam via a simple hydrothermal route followed by calcination. The structures and morphologies of the as-synthesized products were characterized by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis, and the results showed that they were uniformly distributed on the Ni foam support. The surface chemical states of the elements in the samples were identified by X-ray photoelectron spectroscopy. The as-synthesized NiCo₂O₄ products were then tested as cathode materials for supercapacitors in a traditional three-electrode system. The electrochemical performances of the NiCo₂O₄ electrode materials were studied and the area capacitance was found to be 1.26 C·cm^-2 at a current density of 1 mA·cm^-2. Furthermore, outstanding cycling stability with 97.6% retention of the initial discharge capacitance after 10000 cycles and excellent rate performance (67.5% capacitance retention with the current density from 1 to 14 mA·cm^-2) were achieved. It was found that the Ni foam supporting the NiCo₂O₄ nanosheets increased the conductivity of the electrode materials. However, it is worth noting that the contribution of nickel foam to the areal capacitance of the electrode materials was almost zero during the charge and discharge processes. To further investigate the practical application of the as-synthesized NiCo₂O₄ nanosheets-based electrode, a device was assembled with the as-prepared samples as the positive electrode and active carbon (AC) as the negative electrode. The assembled supercapacitor showed energy densities of 0.14 and 0.09 Wh·cm^-3 at 1.56 and 4.5 W·cm^-3, respectively. Furthermore, it was able to maintain 95% of its initial specific capacitance after 10000 cycles. The excellent electrochemical performance of the NiCo₂O₄ nanosheets could be ascribed to their unique spatial structure composed of interconnected ultrathin nanosheets, which facilitated electron transportation and ion penetration, suggesting their potential applications as electrode materials for high performance supercapacitors. The present synthetic route can be extended to other ternary transition metal oxides/sulfides for future energy storage devices and systems.     

Asymmetric supercapacitors based on high capacitance Ni6MnO8 and graphene

A fast, facile and cost-effective method is used to synthesize Ni₆MnO₈ electrode with high electrochemical performance. The supercapacitor based on Ni₆MnO₈ electrode exhibits excellent stability, high area specific capacitance and promising energy and power density.     

Flexible asymmetric supercapacitor with high energy density based on optimized MnO2 cathode and Fe2O3 anode

A flexible asymmetric supercapacitor is assembled using MnO₂ nanosheets/carbon fabric and Fe₂O₃/carbon fabric electrodes. By optimizing the reaction condition of the two electrodes, the device shows high energy densities and excellent flexibility.     

基于钴酸锂载体构筑高体积比容量硫基复合材料

锂-硫电池具有高的理论质量/体积能量密度,因而成为最具发展潜力的高比能二次电池体系. 然而,由于硫载体通常采用轻质的碳纳米材料,导致硫基复合材料的振实密度和体积比容量均偏低,制约了电池体积能量密度的提升. 本文尝试采用具有高密度特征的钴酸锂(LiCoO₂)作为硫的载体材料,以构筑高振实密度的硫基复合材料,进而提高硫正极的体积比容量. 研究显示,LiCoO₂对可溶性多硫化物具有较强的吸附作用,能够促进硫的电化学转化,因而提高了硫的活性物质利用率和循环稳定性. 同时,由于具有高的振实密度(1.90 g·cm^-3),S/LiCoO₂复合材料的首周体积比容量高达1750.5 mAh·cm^-3,是常规硫/碳复合材料的2.2倍. 因此,本文利用具有高密度特征的LiCoO₂作为硫载体来提升硫复合材料的体积比容量,有助于实现锂-硫电池的高体积能量密度.     

Preparation and Pseudo-capacitance Performance of NiCo2O4 Nanosheets

Ternary nickel cobaltite(NiCo₂O₄), as a promising electrode material for supercapacitors, has attracted increasing attention for its excellent electrochemical properties. In this study, novel NiCo₂O₄ nanosheets were rationally designed and prepared using dealloying process, followed by an oxidation treatment. The as-prepared sample was characterized by microstructural and electrochemical techniques in view of its possible application in supercapacitors. The as-prepared sample exhibited high specific capacitance and excellent durability. The specific capacitance reached 663 F/g at 1 A/g and the rate capacitance high up to 73.6% when the current density increased from 1 A/g to 20 A/g. After 5000 cycles of galvanostatic charge-discharge durability test at 4 A/g, the capacity retention rate was 82.1%. The results indicate that versatile dealloying can be used to prepare robust electrode for supercapacitor application.