合成气制液化石油气复合催化剂的性能

 将甲醇合成催化剂与负载 Pd 的分子筛颗粒混合制得复合催化剂, 在连续固定床反应器上考察了该催化剂对合成气一步法制液化石油气 (LPG) 的性能. 采用 N₂ 吸附-脱附、_NH3 程序升温脱附和程序升温氧化对催化剂进行了表征. 结果表明, 分子筛孔径对 LPG 选择性影响显著, 当采用孔径为 0.74 nm × 0.74 nm 的 Y 型分子筛时 LPG 选择性最高. 在 300 ^oC, 2.1 MPa 和空速 1 500 h^-1 条件下, 含有 Y 型分子筛的复合催化剂上 CO 转化率达 80.2%, LPG 占烃类产物的 73.8%. 在一步法合成 LPG 反应中, 催化剂表面积炭是导致 CO 转化率和 LPG 选择性下降的主要原因.     

磁性Y-MOF@SiO2@Fe3O4催化剂的制备及其在Aza-Micheal加成反应中的性能

在磁性SiO₂@Fe₃O₄纳米微球表面原位合成包覆不同含量的Y-MOF,从而制备出新型磁性Y-MOF@SiO₂@Fe₃O₄催化剂。采用XRD、TEM、FT-IR、VSM和N₂吸附-脱附测试等手段对催化剂的结构进行表征,并且评价了催化剂对苯胺和丙烯酸甲酯的Aza-Micheal加成反应性能。结果表明Y-MOF能均匀包覆在磁性SiO₂@Fe₃O₄纳米微球表面,形成具有核壳结构的磁性Y-MOF@SiO₂@Fe₃O₄催化剂,催化剂具有良好的超顺磁性。Y-MOF含量为43.3%（w/w）的Y-MOF@SiO₂@Fe₃O₄催化剂,在苯胺和丙烯酸甲酯的Aza-Micheal加成反应表现出最好的催化性能,丙烯酸甲酯的转化率为88.3%时,N-（β-甲氧碳酰乙基）苯胺的选择性可达99.8%。反应后的催化剂可以通过外磁场容易回收,并且重复使用5次其转化率和选择性没有明显下降。     

酸碱双功能MgO/HMCM-22催化剂上Knoevenagel缩合反应

采用浸渍法制备了一系列MgO改性催化剂MgO/HMCM-22, 利用X射线衍射、N₂物理吸附-脱附、扫描电镜、傅里叶变换红外光谱、NH₃及CO₂程序升温脱附等技术对所制催化剂进行了表征. 结果表明, MgO改性后MCM-22分子筛仍保持原有的结构; 随着MgO负载量的增加, 催化剂的碱强度和碱含量显著增加, 而强酸含量明显减少, 弱酸酸位有所增加. 以Knoevenagel缩合为探针反应, 考察了所制催化剂的性能. 在优化的反应条件下, MgO/HMCM-22上苯甲醛转化率高达92.6%. 催化剂 MgO/HMCM-22和MgO/NaMCM-22的催化性能明显优于HMCM-22和MgO. 酸中心和碱中心均对该缩合反应起着重要的促进作用. MgO/HMCM-22对Knoevenagel缩合反应显示出较高的催化活性, 体现出明显的酸碱协同催化作用.     

Pd-Al2O3-BEA催化剂催化油脂一步加氢制航空燃油烃类性能

采用浸渍法制备了系列H-β分子筛修饰的Pd/Al₂O₃催化剂,通过XRD、低温N₂吸附、NH₃-TPD等分析表征技术和以油酸甲酯为模型化合物的加氢反应体系,探索了H-β分子筛的加入方式和含量对催化剂催化性能的影响。结果表明,由于加入方式不同,Pd-Al₂O₃-BEA催化剂组成要素之间的相互作用呈现较大差异,从而使其催化性能呈现较大不同。在Pd/（BEA-Al₂O₃）中,随着H-β分子筛加入量的增加,催化剂的比表面积、孔容、强酸酸量呈增大趋势,弱酸酸量呈先增大后减小趋势,平均孔径呈减小趋势。由于Pd/（45% BEA-Al₂O₃）催化剂具有合适的微孔孔分布、适中的强酸酸量、最大的弱酸酸量,使其呈现出最大的航空燃油烃类选择性,异构烷烃选择性和一定比例的环烷烃和芳香烃产物。     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

多级孔NiMo负载TS-1分子筛催化剂的制备及其加氢脱硫性能

钛硅(TS-1)分子筛的微孔孔道严重限制了其在复杂分子催化转化中的应用,为了克服这一问题,通过酸洗脱、碱刻蚀及二者相结合的方法制备了多级孔 TS-1 分子筛,并采用等体积共浸渍法制备了相应的 NiMo 负载型催化剂;使用 X 射线衍射(XRD)、N₂吸附-脱附、吡啶吸附红外光谱(Py-FTIR)、氢气程序升温还原(H₂-TPR)、X射线光电子能谱(XPS)和高分辨透射电子显微镜(HR-TEM)等方法对多级孔TS-1分子筛的理化性质进行了表征;以二苯并噻吩(DBT)为探针对催化剂的加氢脱硫(HDS)性能进行了评价。结果表明,和常规TS-1分子筛相比,多级孔TS-1分子筛保持了MFI拓扑结构,比表面积增大且具有介孔结构,分子筛表面形成了适量的Brønsted酸中心;相应催化剂上活性金属与载体间相互作用得以改善,MoS₂片晶长度和堆垛层数适宜,形成了更多的 NiMoS活性相;催化剂活性和选择性均有所提升,尤其是酸洗脱获得的 NiMo/AT-TS-1催化剂的活性相较未经处理的NiMo/TS-1催化剂提升了1.2倍,直接脱硫(DDS)路径选择性提升了22%。     

多级孔NiMo负载TS-1分子筛催化剂的制备及其加氢脱硫性能

钛硅(TS-1)分子筛的微孔孔道严重限制了其在复杂分子催化转化中的应用,为了克服这一问题,通过酸洗脱、碱刻蚀及二者相结合的方法制备了多级孔TS-1分子筛,并采用等体积共浸渍法制备了相应的NiMo负载型催化剂;使用X射线衍射(XRD)、N₂吸附-脱附、吡啶吸附红外光谱(Py-FTIR)、氢气程序升温还原(H₂-TPR)、X射线光电子能谱(XPS)和高分辨透射电子显微镜(HR-TEM)等方法对多级孔TS-1分子筛的理化性质进行了表征;以二苯并噻吩(DBT)为探针对催化剂的加氢脱硫(HDS)性能进行了评价。结果表明,和常规TS-1分子筛相比,多级孔TS-1分子筛保持了MFI拓扑结构,比表面积增大且具有介孔结构,分子筛表面形成了适量的Brønsted酸中心;相应催化剂上活性金属与载体间相互作用得以改善,MoS₂片晶长度和堆垛层数适宜,形成了更多的NiMoS活性相;催化剂活性和选择性均有所提升,尤其是酸洗脱获得的NiMo/AT-TS-1催化剂的活性相较未经处理的NiMo/TS-1催化剂提升了1.2倍,直接脱硫(DDS)路径选择性提升了22%。     

M/Al2O3-CeO2（M=Pt-Ru，Ru，Pt）催化剂在甲胺催化湿式氧化中的活性与选择性

采用浸渍法制备了M/Al₂O₃-CeO₂（M=Pt-Ru,Ru,Pt）催化剂,并将其用于甲胺的催化湿式氧化反应（CWAO）.结果表明,Pt-Ru/Al₂O₃-CeO₂具有最佳活性和选择性.运用程序升温还原、X射线光电子能谱、X射线衍射、透射电子显微镜、N₂吸附和CO化学吸附等技术对催化剂的物化性质进行了表征.Pt组分的引入可有效提高双金属催化剂活性组分的分散度,从而明显提高了其催化性能.升降温过程中总有机碳（TOC）转化率与N₂选择性迟滞效应表明,甲胺CWAO遵循化学吸附-脱附机理.     

不同聚合物分散剂对Pt/SAPO-11催化剂性能的影响

采用浸渍法制备了经过不同聚合物分散剂处理的Pt/SAPO-11催化剂,并通过X射线衍射(XRD)、透射电子显微镜(TEM)、N₂吸附-脱附和N_H3程序升温脱附(TPD)等对催化剂的组织结构进行了表征。结果表明,分散剂不会破坏催化剂的结构,反而提高了其孔体积、孔径和比表面积,同时改变了沸石的酸强度和酸量,其中以聚乙烯吡咯烷酮处理的Pt/SAPO-11催化剂孔体积、孔径和酸性分布最佳。在固定床反应器上对不同分散剂处理的Pt/SAPO-11催化剂催化性能进行评价,结果表明聚乙烯吡咯烷酮处理的Pt/SAPO-11催化剂也表现出最佳的催化性能,麻风树油的加氢脱氧率高达99.45%,生物航空煤油组分收率和异构烷烃组分(C₈~C₁₆)的选择性分别达到了44.67%和56.37%。     

HAlMCM-41介孔分子筛催化1,3-苯并二噁茂烷合成的研究

研究了HAlMCM-41分子筛催化邻苯二酚与环己酮、丁酮、丙酮、丙醛、丁醛、异丁醛、戊醛、正己醛、正辛醛、苯甲醛、二苯甲酮等十余种醛(酮)的缩合反应. 考察了反应时间、酚与醛(酮)的配比、HAlMCM-41分子筛用量、硅铝比、催化剂重用次数等因素对邻苯二酚与醛(酮)反应的影响. 结果表明, 当邻苯二酚与醛(酮)物质的量比为1∶1.4, 催化剂用量为3.5 g/mol邻苯二酚, 反应4 h, 分子筛n(SiO₂)/n(Al₂O₃)为15时, 选择性一般在99.4%以上, 转化率也一般在85.6%以上, 因此, HAlMCM-41分子筛对邻苯二酚与醛(酮)的反应有较好的催化性能.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。