近红外光谱相似性评估结合局部回归方法无损检测苹果糖度

基于Bayesian相似性评估方法结合偏最小二乘局部回归,对苹果近红外数据库进行数据挖掘。通过相似性计算方法搜索出与预测样品相近的近红外光谱,形成校正子集后采用局部回归方法获得待测样品的相关信息。该方法所建立局部模型的平均检验标准偏差(SEV)约为0.57,分析30个预测样品的预测标准偏差(SEP)约为0.61;基于马氏距离的传统方法建立的偏最小二乘局部模型的平均SEV为0.59,分析30个待测样品的预测SEP为0.64;而采用整个数据库建立的全局偏最小二乘模型的SEV约为0.65,分析30个预测样品SEP约为0.70。基于Bayesian相似性评估的局部回归方法在苹果糖度的近红外无损定量分析中获得较好的应用结果,在实际应用中该方法比全局回归方法具有更强的适用性,为近红外光谱分析提供了新的分析工具。     

苯乙烯/丙烯酸正丁酯乳液聚合反应过程中残余单体含量的实时监测

采用近红外光谱分析技术在线测量苯乙烯(St)/丙烯酸正丁酯(BA)乳液聚合体系中残余单体的含量. 共设计9个半连续方式的St/BA乳液共聚反应, 在反应过程中实时取样测量其残余单体含量, 并记录取样时刻对应的聚合体系的近红外光谱. 采用多元散射校正法(MSC)处理光谱, 有效地克服了乳胶粒子散射效应对近红外光谱分析的影响. 采用主成分分析法(PCA)对乳液体系的近红外光谱数据进行了解析. 选取6个聚合反应对应不同反应时间的72个样品, 用于建立校正模型, 另外3个聚合反应共取36个样品用于校正模型的验证, 并在反应设计上体现了乳化剂用量的变化, 从而使校正模型对乳化剂用量的变化具有一定的适应性. 研究结果表明, 所得模型对残余单体St和BA含量的预测结果标准差(SEP)分别为0.08026和0.05305.     

基于稳定一致波长筛选的无标样近红外光谱模型传递方法

测量环境及仪器间光谱信号的差异导致近红外光谱模型从主机传递到从机后,经常会产生过大误差。本研究提出了一种基于稳定一致波长筛选的无标样近红外模型传递方法(Screening stable and consistent wavelengths,SSCW),剔除主从仪器间差谱的标准偏差大于样品精密度测试光谱标准偏差的波长,以及精密度测试偏差过大的波长,筛选出仪器间光谱信号一致性好且稳定的波长建立近红外光谱定标模型。分别以玉米和黄芩样本集对本算法的有效性进行了检验。结果表明,SSCW模型传递后对从机样品的预测均方根残差RMSEP较全波长PLS模型直接传递结果小一个量级,大部分情况下优于分段直接校正算法(Piecewise direct standardization,PDS)的结果和文献报道的无标样模型传递结果。本方法具有传递性能好、模型参数少、稳健等优点,在不同仪器间可实现近红外光谱模型的无标样传递。     

黄连中小檗碱的近红外检测技术和预处理方法

以黄连中的黄连素为研究对象,采用了65个样品进行研究,建立了黄连中小檗碱的近红外快速检测方法。针对在近红外光谱分析研究中,样品的光谱中常常包含由光散射导致的干扰信息,采用了一种新颖的预处理方法光程估计与校正(OPLEC)对光谱进行处理,并与原始光谱建立的模型进行比较,研究了消除黄连颗粒近红外漫反射光谱散射的最佳预处理方法。实验表明,光谱预处理后建立的模型在稳健性上均有提升,其中光程估计与校正预处理法对消除光散射有着显著的效果。模型的交叉验证均方根误差(RMSECV)从0.1485降低到0.0369,相关系数R从0.9513提高到0.9854,预防均方根误差(RMSEP)从0.1145降低到0.0578。     

人工神经网络方法用于PC/ABS材料定量分析

采用人工神经网络(ANN)算法建立了不同共混比的ABS/PC样品的近红外光谱数据与共混比的定量校正模型,并对校正模型的准确性进行了验证。实验分析结果表明,该方法适合于高分子材料共混比的测定。     

近红外光谱测定溶液中甲醇的含量

测量了含微量甲醇(体积分数为0.04%～0.24%)的系列乙醇水溶液的近红外光谱,利用近红外光谱分析建立了预测甲醇含量的定量分析模型。比较了用外部检验法(Test Set-Validation)和交叉检验法(Cross-Validaton)建立的数学模型,研究了使用外部检验法时,校正集和检验集样品数的改变对模型预测结果的影响。结果发现,当校正集样品数为15检验集样品数为6(总样品数为21)时,使用外部检验法建立的数学模型预测结果较好,其校正集的均方根误差和检验集的预测均方根误差(分别为RMSEE和RMSEP)均较小(分别为0.0115和0.0105),而且很接近。结果表明,近红外光谱方法简单,准确而且实用。     

近红外光谱法测定ABS树脂中氮含量

根据58个丙烯腈-丁二烯-苯乙烯(ABS)树脂样品的近红外漫反射光谱数据结合偏最小二乘法(PLS)建立了ABS树脂中氮含量定量分析的校正模型。结果表明;在近红外光谱区(7501.8～5449.9cm~(-1))内,主因子数为9时,定量模型的准确度最好。通过对模型进行t-检验,在显著性水平为0.05的条件下,其测定结果与标准方法的测定结果对比,两者无显著性差异。预测相关系数(r)和相对标准偏差(RSD)分别为0.9924和3.3%。     

近红外光谱用于注射用曲克芦丁质量控制研究

运用近红外光谱(NIRS)分析技术建立注射用曲克芦丁的定量分析预测模型,并进行相关验证。近红外积分球漫反射光谱法对73个批次样品进行采集得到NIRS图,根据高效液相色谱法(HPLC)测定样品的有效成分含量并测得样品pH值,使用TQ Analyst光谱分析软件运用偏最小二乘法(PLS)建立定量分析方法模型。模型结果显示,含量预测模型的线性相关系数(R)为0.99239,校正标准偏差(RMSEC)和预测标准偏差(RMSEP)分别为0.1790和0.5460,pH值预测模型R为0.81575,RMSEC和RMSEP分别为0.0749和0.0704。验证结果显示,含量与pH值预测模型外部验证结果的平均误差率分别为0.46%和1.57%,且t检验无显著性差异(P>0.05)。NIRS分析技术可快速稳定的对产品含量和pH值进行预测,对产品质量控制提供了新的方法依据。     

废旧涤/棉混纺织物近红外定量分析模型的建立及预测

将中红外光谱筛选出的598个纯涤、纯棉及涤/棉混纺样本采用GB/T 2910.11-2009法测定其涤、棉准确含量,其中校正集样本252个,验证集样本346个。使用便携式近红外光谱仪获取样本的原始近红外光谱(NIRS)。校正集样本依据回归系数的分布趋势和范围选取最佳建模谱区,并采用差分一阶导、S-G平滑和均值中心化相结合的方法对原始光谱进行预处理,利用偏最小二乘法(PLS)建立涤/棉混纺织物中涤含量的近红外(NIR)定量分析模型。同时分析了样本颜色对NIRS的影响,探讨了斜线光谱样本、奇异样本和不同组织结构织物对模型预测效果的影响。结果表明:利用PLS法建立的涤/棉混纺织物定量分析模型最优组合包含1个光谱区间和9个主成分因子,校正集相关系数(RC)为0.998,标准偏差(SEC)为0.908。为验证所建模型的有效性和实用性,对346个未参与建模的涤棉样本进行了预测,并将预测结果与国标法测定值进行方差分析,两种方法结果无显著差异,预测正确率达97%以上。模型的建立为废旧涤/棉混纺织物快速、无损分拣提供了基础数据库。     

PDS用于不同温度下的近红外光谱模型传递研究

采用合适的计算方法可降低测定环境对近红外光谱校正模型稳健性的影响。该文以喷气燃料为研究对象,考察了分段直接校正算法对所建模型预测结果的影响,通过选择转移样品数及窗口宽度,建立了最佳的校正模型和光谱转移参数。结果表明,在20℃下建立近红外光谱校正模型,直接预测30℃下喷气燃料的密度,预测集样品均方根误差（RMSEP）为0.2031,而30℃近红外光谱采用分段直接校正算法模型转移后,预测集样品均方根误差（RMSEP）降低为0.1354,预测结果得到明显改善,有效地解决了样品温度对近红外光谱分析结果的影响。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).