顶空固相微萃取/气相色谱-质谱联用测定水中6种挥发性硅氧烷

建立了水中4种环形和2种线形硅氧烷的顶空固相微萃取/气相色谱-质谱联用分析方法.考察了萃取纤维、萃取温度、萃取时间、水样pH值、解析时间、盐效应等因素对实验结果的影响.优化后的条件为:40mL水、40 μL内标(M4Q,500 μg/L)、NaCl(0.1 g/mL)加入60 mL顶空瓶中,选用65μm聚二甲基硅氧烷-二乙烯基苯(PDMS/DVB)纤维于24℃顶空萃取45 min.萃取完成后将纤维插入气相色谱进样口,于200℃解吸2 min进行定性、定量分析.结果表明,6种目标物的方法检出限为(LOD)2.6～7.8 ng/L,回收率为82％～ 96％,相对标准偏差(RSD)为1.1％～7.9％.     

羧基化单壁碳纳米管涂层同时测定纯净水中的烷基酚和双酚A

用溶胶-凝胶方法制备了羧基化碳纳米管溶胶凝胶固相微萃取涂层,采用顶空固相微萃取-气相色谱法测定纯净水中的烷基酚和双酚A.优化了萃取涂层的萃取时间、萃取温度、盐浓度以及解析时间等实验参数.结果表明,在萃取温度为90℃和盐浓度为0.36 g/mL的条件下萃取30 min,250℃下解析3 min,涂层的萃取效果最好.与商用...     

聚醚砜酮涂层纤维顶空固相微萃取-气相色谱法分析水中痕量的酚类化合物

应用自制的聚醚砜酮(PPESK,30 μm)涂层纤维,采用顶空固相微萃取-气相色谱法测定水中痕量的酚类化合物。优化了固相微萃取温度、萃取时间、pH值和离子强度。方法的检出限为0.003～0.041 μg/L,相对标准偏差低于16%(n=5)。将PPESK涂层纤维与商品化的聚丙烯酸酯涂层纤维对比,结果表明PPESK萃取酚类化合物有较高的萃取富集倍数。用所制备的PPESK萃取头分析自来水、海水等实际水样,20 μg/L添加水平下的回收率分别为100.5%～111.8%和94.8%～117.3%。     

顶空固相微萃取-气相色谱-质谱法同时测定饮用水源水中24种VOCs

建立了同时测定饮用水源水中24种挥发性有机物(VOCs)的顶空固相微萃取-气相色谱-质谱法.用75 μm CarboxenTM-Polydimethylsiloxane(CAR-PDMS)固相微萃取柱顶空萃取水样中的VOCs,VOCs用气相色谱-质谱联用仪检测,采用内标法定量.对萃取柱涂层、样品盐度、萃取温度和萃取时间等样品前处理条件进行了优化,VOCs的检出限在0.03～0.31 μg/L之间,线性相关系数r＞0.996(二氯甲烷和三氯甲烷除外).对饮用水源水实际水样0.50μg/L和1.00 μg/L两个加标浓度水平的回收率进行了测定,三氯甲烷回收率均值分别为104％和142％,其余VOCs回收率分别为90.0％～120％和88.0％～110％,除二氯甲烷和三氯甲烷外,其余VOCs测定结果的相对标准偏差均小于15.0％(n=6).该方法适用于饮用水源水中挥发性有机物的监测分析.     

顶空固相微萃取谱-气相色谱-质谱联用测定饮用水中6种致嗅化合物

采用顶空固相微萃取谱-气相色谱-质谱联用法对饮用水中2-甲基异茨醇、土味素、2-甲氧基-3-异丙基吡嗪、2-甲氧基-3-异丁基吡嗪、2,4,6-三氯苯甲醚和2,3,6-三氯苯甲醚共6种致嗅化合物进行了分析。通过对固相微萃取纤维的类型、解吸附时间、NaCl溶液浓度、溶液pH、顶空温度、转速、顶空时间等顶空条件及GC-MS条件的优化,建立了一次性顶空固相微萃取快速测定饮用水中6种致嗅化合物的方法。采用0.10 mol/L的NaOH溶液将水样调至pH 6.0。以DVB/Carboxen/PDMS涂层的固相微萃取纤维头对20 mL添加了NaCl溶液浓度为0.3 g/mL的水样于70℃水浴顶空萃取25 min。被萃取的致嗅化合物于250℃解吸附4 min供GC-MS分析。6种致嗅化合物在0.25～100 ng/L范围内线性关系良好(R>0.986),检出限低于0.1 ng/L。对实际水样进行分析,低、中、高3种不同浓度的加标回收率为93.0%～106.6%,相对标准偏差为3.0%～6.6%(n=6)。该分析方法可对饮用水中6种致嗅化合物进行同时监测。     

溶胶-凝胶富勒烯固相微萃取-气相色谱法测定塑料水浸泡液中多种邻苯二甲酸二酯

利用新型溶胶-凝胶富勒烯涂层,结合顶空固相微萃取-气相色谱法-FID检测,对PVC塑料制品在水溶液浸泡液中的12种邻苯二甲酸二酯进行了分析和测定,其检出限为0.097～3.646 μg/L;回收率为87.9%～107%;RSD<8%.对12种邻苯二甲酸二酯类增塑剂的固相微萃取条件和色谱条件进行了优化,并与商用固相微萃取聚二甲基硅氧烷(PDMS)探头的性能进行了比较.本方法应用于PVC玩具及PVC餐垫样品的分析,结果令人满意.     

顶空固相微萃取-气相色谱-质谱联用分析干柴胡药材中有机挥发物

采用顶空固相微萃取与气相色谱-质谱联用技术检测分析干柴胡药材中挥发性成分,选用聚丙烯酸酯涂层,就萃取时间、温度、体积、样品量、预热时间及脱附时间等条件进行了优化,结果表明,30mL萃取瓶里0．5g样品90℃温度下预热40min后,以85μmPA涂层顶空萃取50min,于250℃脱附5min,测得88个峰,鉴定26种化合物成分。方法所得结果与传统提取方法(蒸馏提取法)比较,相对含量较高的成分一致,方法重现性理想,可应用于柴胡药材挥发性物质的快速分析。     

聚吡咯-离子液体固相微萃取涂层的电沉积制备及其在苯类化合物气相色谱检测中的应用

在0.1 mol/L吡咯-0.1 mol/L对甲苯磺酸-4g/L 1-丁基-3-甲基咪唑四氟硼酸盐水溶液中,通过循环伏安法在不锈钢丝表面制备了新型聚吡咯-离子液体(Polypyrrole-ionic liquid,PPY-IL)涂层.此涂层呈菜花状结构,粒度比PPY小.以5种苯类化合物(即1,2-二甲苯、1,2,4-三氯苯、1,2-二氯苯、1,2,4-三甲苯和1,3,5-三甲苯)为目标分析物,对所得萃取头性能进行了考察.在优化的实验条件(萃取温度:50℃；萃取时间:40 min;搅拌速率:600 r/min; NaCl浓度:0.2 g/mL)下,对这些苯类化合物进行顶空固相微萃取-气相色谱检测,其线性范围为0.6～800 μg/L,单根多次萃取的相对标准偏差小于4.5％(n=5),多根萃取头平行萃取的相对标准偏差为4.5％～12.4％(n=5).PPY-IL萃取头有良好的稳定性,在使用150次后萃取性能仅有很小的变化；在温度升至290℃时不分解.与聚吡咯和聚二甲基硅氧烷萃取头相比,本萃取头对这些苯类化合物有更高的萃取能力.     

自动顶空衍生化固相微萃取法测定啤酒中的老化醛类化合物

采用邻-五氟苯甲基羟胺(PFBOA)衍生,顶空固相微萃取(HS-SPME)和气相色谱质谱(GC-MS)测定啤酒中2-甲基丁醛、3-甲基丁醛、反-2-壬烯醛等8种老化醛类化合物.顶空固相微萃取采用65 μm PDMS/DVB纤维,先用纤维吸附PFBOA溶液,再将纤维插入装有2 mL啤酒的20 mL顶空进样瓶的顶空中在60 ℃萃取60 min,衍生和萃取都在自动进样器中进行.采用GC-MS检测,特征离子为m/z 181.8种羰基化合物在0.2～500 μg/L范围内线性关系良好,相关系数在0.990以上.检测样品的相对标准偏差为1.0%～15.7%,回收率为88%～103%.同时研究并讨论了萃取纤维、萃取温度、萃取时间、样品体积等因素对醛类萃取量的影响.该方法可用于啤酒保鲜期研究和产品质量控制.     

顶空-固相微萃取-气相色谱法检测可可麦汁中吡嗪类化合物

建立了顶空-固相微萃取(HS-SPME)-气相色谱快速测定可可麦汁中3种吡嗪类物质(2,5-二甲基吡嗪、2,3,5-三甲基吡嗪和2,3,5,6-四甲基吡嗪)的方法.选择不同的固相微萃取头对萃取温度和时间进行优化,所得最佳萃取条件为:在60℃下,采用75 μm CAR/PDMS萃取头对麦汁样品萃取40 min.本方法的检出限(S/N=3)为0.023～ 0.056 μg/L,线性范围1～500 mg/L;相对标准偏差为3.6％～6.4％;回收率为95.4％～102.7％.本方法应用于样品检测,发现可可麦汁中吡嗪的浓度与原料中可可粉的添加量正相关,显示了很好灵敏性.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.