萘与丙烯在脱铝丝光沸石上的烷基化反应

Shape selective alkylation of polynuclear aromatics has begun to receive increasing attention. 2,6 dialkylnaphthalenes are important raw materials for manufacturing high quality polyester fibers and plastics. Understanding of the reaction and the catalysis for conversion of polycyclic aromatic hydrocarbons is needed both from fundamental and practical view points. In this paper, alkylation of naphthalene with propene over a series of dealuminated mordenite with different Si/Al ratios was carried out in an autoclave with an electromagnetical stirrer. Textural property of the dealuminated mordenite was determined by nitrogen adsorption. The amount of the acid sites was measured by NH 3 TPD. The catalytic activity of HM and β shape selectivity for products increased with increasing the Si/Al ratio in HM. Moreover, the selectivity for alkylation with propene was also increased by dealumination treatment. The increase of the catalytic activity was attributed to the formation of mesopores, which significantly promoted the diffusion of reactants and products in mordenite. It was suggested that the increase of β selectivity resulted from the elimination of acid sites from the external surface, and the selectivity for alkylation with propene was improved owing to the creation of the interconnection between 12 ring and 8 rimg channels by dealumination.     

Determination of Size Distribution of Nano-particles by Capillary Zone Electrophoresis

A new method was developed for the determination of the size distribution of nano-particles by capillary zone electrophoresis (CZE). Scattering effect of nanoparticles was studied. This method for the determination of size distribution was statistical.     

Analysis of nitrobenzene compounds in water and soil samples by graphene composite-based solid-phase microextraction coupled with gas chromatography–mass spectrometry

In this work, solid-phase microextraction coupled with gas chromatography–mass spectrometry was developed to determine trace levels of nitrobenzene compounds in water and soil samples. Graphene was chosen as the extraction material and its composite was coated on a stainless steel wire through sol–gel technique for the solid phase microextraction. The key parameters influencing the extraction efficiency were optimized. Under the optimal conditions, the linearity for the compounds was observed in the range of 0.02–15.0 mg/L for water samples, and 0.2–60.0 mg/kg for soil samples, with the correlation coefficients（r） of 0.9966–0.9987. The limits of detection of the method were 0.0025–0.005 mg/L for water samples, and 0.02–0.04 mg/kg for soil samples. The recoveries for the spiked samples were in the range of 72.0%–113.2%, and the precision, expressed as the relative standard deviations, was less than 12.1%.     

Pd-gate MOS sensor for detection of methanol and propanol

The present paper focused on the detection of methanol and propanol using Pd-gate metal-oxide-semiconductor (MOS) sensor. Surface mor- phology and composition of the gate film were studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The response of the sensor for propanol and methanol was measured as shift in capacitance-voltage (C-V) and conductance-voltage (G-V) curves of the MOS structure. The sensitivity of the sensor towards methanol was found to be greater than that towards propanol. It was 58.2% for methanol and 32% for propanol (at 0.6 V, 1 MHz) in terms of capacitance measurements, while in terms of conductance results the sensitivity was found to be 57.2% for methanol and 38.9% for propanol at 1 kHz. The discontinuities or cracks present in the microstructure of the gate material are believed to be mainly responsible for the high sensitivity of the sensor, going with the decomposition of gas molecules and subsequent hydrogen permeation through Pd.     

STUDY ON ASPIRIN-MAA HYDROGEL MIP SYSTEM

The controlled release system of MIP-Asp hydrogel was prepared by using self-assembly molecular imprinted technique （MIP）. ^1H NMR was used to detect the changes of active hydrogen atoms. Moreover, the effect of crosslinking degree of hydrogel on the release of medicine was investigated and the temperature/pH sensitivity was also considered. The results demonstrated that： the MIPs-Asp was a procedure involving the participation of active hydrogen; the lower crosslinking degree corresponded to the higher medicine release ratio; high temperature is better for the release; weak acidity is better for the release of Asp.     

Highly efficient heterogeneous procedure for the synthesis of fructone fragrancy

A novel heterogeneous strong acid catalyst was synthesized through the copolymerization of p-toluenesulfonic acid and paraformaldehyde and utilized for the synthesis of fructone. The results showed that the catalyst was very efficient for the reaction with the yield over 95%. The advantages of extremely high density of acidity, high thermal and chemical stability, low cost for the simple synthetic procedure, and reusability made the catalyst one of the best choices for the reaction.     

Microwaves spark emission spectroscopy for the analysis of cations:A simple form of atomic emission spectroscopy

A novel method for the cation analysis was investigated.The analysis is based on the sparking of the salts of metals in a microwave oven after placing in a graphite cell.The graphite cell absorbs microwaves and produces high temperature which converts the salt into light emitting species.The colour of light was found to dependent on the nature of cation,however,the intensity of the emitted light was found to be depending upon the form and shape of the graphite assembly in addition to the concentration of the salt.This communication presents explanation for all these observations and for the systematic and quantitative analysis using microwave spark emission technique.     

Multianalyte Biosensor for Simultaneous Determination of Glucose and Galactose Based on Micromachined Chamber-type Electrodes

An amperometric multianalyte biosensor for the simultaneous determination of glucose and galactose was developed based on chamber-type electrodes, which were fabricated by micromachining technology. The dual cham-ber-type enzyme electrode with glucose and galactose sensor elements was integrated onto one microchip. The experimental parameters of this biosensor were optimized. The biosensor exhibited a linearity of up to 4.0 mol/L for glucose and 4.5 mol/L for galactose, and the response time was about 30 s for glucose and 40 s for galactose. No cross-talking behavior was investigated in the course of simultaneous measurement of the two analytes. Interference from electroactive species, such as ascorbic acid and uric acid, was minimized due to the permselectivity of Nation film. In addition, the biosensor displayed a storage stability of longer than one month.     

Ethylene glycol aluminum as a novel catalyst for the synthesis of poly(ethylene terephthalate)

Ethylene glycol aluminum was prepared efficiently and characterized by FT-IR and NMR.It exhibited higher catalytic activity and had profitable effect than titanium glycolate and ethylene glycol antimony for the synthesis of poly(ethylene terephthalate) (PET).It was only used as polycondensation catalyst because it was sensitive to water.For this catalyst,the degree of esterification of the theoretical amount of water was produced up to 95%at 260℃,while the intrinsic viscosity and content of terminal carboxyl groups of the corresponding PET polyester,polymerized at 280℃,70 Pa for 39 min,was 0.87 dL/g and 23.0μmol/g,respectively. Ethylene glycol aluminum was a promising catalyst for the synthesis of PET polyester.     

Determination of Melatonin in Rat Pineal Gland and Drug with Flow-Injection Chemiluminescence

A flow-injection chemiluminescence （CL） method for the determination of melatonin based on the CL reaction of melatonin with hydrogen peroxide and sodium hypochlorite （NaOCl） in a basic alkaline solution was developed. The possible CL mechanism has been discussed, and a proposal for the reaction pathway was given that singlet oxygen was clarified to be produced in this reaction system and was responsible for the CL emission. Under the optimized conditions, the linear concentration range of application was 1.0×10^-7-2.5 × 10^-4 moloL-I with a de- tection limit of 5.0 ×10^-8 moloL-1 （S/N= 3）. The relative standard deviation for eight repeated measurements of 1.0×10^-6 mol·L^-1 melatonin was 2.8%. The interferences of several important biological substances, some indole compound, cations and anions were studied. No interference was found for the anions, glucose, starch, most of cations and low concentration （less than 3.0 × 10^-6 mol·L^-1） of some biological substances and indole compound. The method was applied to the determination of melatonin in rat pineal gland and drug with satisfactory results. The sample throughput was 90 injections per hour.     

多壁碳纳米管对PS分子量影响的研究

由于碳纳米管（CNT）具有优异的力学、电学、光学等性能，近年来，聚合物／碳纳米管（polymer／CNT）复合材料的研究已经成为研究者关注的热点。相关的研究主要集中在：一是将CNT作为填充材料制各复合材料，使复合材料的力学、电学等性能得到提高。二是将CNT作为主体，用聚合物对CNT进行修饰，使CNT在有机溶剂中能够获得良好的溶解度。而对于在聚合反应中，CNT的加入对聚合物分子量影响的研究，相关的报道较少。本文利用悬浮聚合法制备了聚苯乙烯／多壁碳纳米管（PS／MWNT）复合材料，采用透射电镜（TEM）和凝胶渗透色谱（GPC）对其进行了分析，详细研究了MWNT对于PS分子量的影响。     

蒙特卡洛法评定在线pH计示值误差的不确定度

以在线p H计为例,考察了在线酸度计示值误差不确定度的分布规律,利用蒙特卡洛法评定示值误差不确定度。对于0.01级的在线p H计,蒙特卡洛法与GUM法评定结果的差值为9.1%,小于不可靠性(20%);对于0.1级的在线p H计,蒙特卡洛法与GUM法评定结果的差值为3.8%,小于不可靠性(10%)。通过比较得出结论,采用GUM法验证了蒙特卡洛法(MCM)根据JJF 1547–2015评定在线p H计示值误差不确定度的方法是有效且适用的。尤其在测量模型非线性以及输出量的概率密度函数(PDF)较大程度地偏离正态分布或t分布等GUM法不适用的场合,蒙特卡洛法是评定在线分析监测仪器仪表示值误差不确定度的重要手段。     

Polymeric controlled release formulations of niclosamide for control of Biomphalaria alexandrina, the vector snail of schistosomiasis

Schistosomiasis is one of the most important public health problems in many developing countries. The present study was conducted to investigate the effect of the polymeric niclosamide formulations against Biomphalaria alexandrina snails, the intermediate host of Schistosoma mansoni in Egypt. Three new polymeric formulations were prepared for the molluscicide niclosamide. The formulations were prepared either by the chemical modifications of poly(glycidyl methacrylate) or by physical entrapment of the niclosamide in calcium alginate beads. The release of the niclosamide from the polymeric formulations was investigated. The activity of the prepared formulations against Biomphalaria alexandrina was investigated. The results obtained revealed higher potency for polymerized niclosamide B3 than B1; the lowest potency was revealed for B2. After an exposure period of 24 hours, LC(50) values were 0.073, 0.098 and 1.09 ppm for B3, B1 and B2, respectively. In addition, the molluscicidal potency of the test polymeric niclosamide was age-dependent, where old snails were more tolerant to the test solutions than young and newly hatched snails. The results also indicated that the molluscicidal activity of B3 was extended for 21 days and 17 days for B1, compared with 5 days for free niclosamide. However, the molluscicidal potency of the polymerized niclosamide was increased after boiling for one hour, and was increased with increasing the pH of the medium to pH 9. In addition, their potency was increased with decreasing the water hardness concentrations (CaCO(3)).Molluscicidal activity of free niclosamide and its polymeric formulations vs. exposure time.     

Utilisation of polypyrrole modified electrode for the determination of pesticides

Cyclic voltammetric studies of isoproturon and carbendazim using polypyrrole modified glassy carbon electrode were carried out. The electrode and reaction conditions, which yielded maximum current signal, were selected for the development of stripping voltammetric procedure for the determination of the pesticides. The oxidation peak around 1.3?V obtained for isoproturon and carbendazim while employing polypyrrole modified electrode showed maximum current response. This peak was chosen for stripping analysis using square wave mode. The experimental parameters were optimized and the calibration plot was obtained. The LOD was 0.5?ng?mL^?1 for isoproturon and 5?ng?mL^?1 for carbendazim. The relative standard deviation for 5 identical measurements was 2.81% and 3.33% for isoproturon and carbendazim respectively. The applicability of the method was verified by determining the pesticides in spiked soil and water samples.     

碳纤维预浸料挥发分测试方法改进

碳纤维预浸料挥发分的测试对于复合材料的工艺成型和制品的使用性能至关重要。为了解决碳纤维预浸料挥发分测试数据偏离理论值的问题,根据基体类型的差异,对挥发分测试方法进行了改进。对烘焙温度和烘焙时间进行考察试验。通过试验确定4211体系预浸料烘焙温度为160℃,烘焙时间为20 min,;氰酸酯体系预浸料烘焙温度为180℃,烘焙时间为60 min,并且需在金属网的下面加入恒重的收集皿。测试方法改进后,测试结果与理论值接近,且测定结果的标准偏差从0.75下降至0.12,提高了挥发分测试结果的精密度和准确度。     

Topological indices and QSPR analysis of some chemical structures applied for the treatment of heart patients

In this study, various beta-blocker drugs used for heart disease were analyzed, and their degree-based topological indices derived from the M-polynomial were calculated. Linear and quadratic regression analysis was used to obtain quantitative structure-property relationship models between the topological indices and eight the physicochemical properties of the drugs to determine their effectiveness. The results show that the harmonic index was the best predictor for boiling point, flashpoint, and enthalpy of vaporization, while the redefined third Zagreb index was effective for polarizability, molar refractivity, and molar volume. The inverse sum indeg index was found to be effective for molar refractivity, and the second modified Zagreb index was surface tension in linear regression models. In addition, the redefined third Zagreb index was the best predictor for polarizability and molar refractivity, while the second modified Zagreb index was effective for molar volume. The SDD index was found to be effective for surface tension in quadratic regression models.     

电感耦合等离子体原子发射光谱法测定钒铁中8个杂质元素含量和方法精密度的验证

提出了电感耦合等离子体原子发射光谱法(ICP-AES)测定钒铁中硅、磷、铝、锰、镍、铬、铜、钛共8个杂质元素含量的方法。钒铁样品(0.5000g),先后加入50%(体积分数)硝酸溶液20mL及50%(体积分数)盐酸溶液10mL,在100℃左右加热溶解,溶解过程中应注意保持溶液体积在25mL左右。将溶液过滤并置于200mL容量瓶中作为母液留用。将滤纸及不溶物一并移入铂坩埚中,置于马弗炉中,先于250℃灰化20min,稍冷后加入无水碳酸钠和硼酸(质量比2∶1)组成的混合熔剂0.3g,升温至950℃融熔15min。冷却,用体积比1∶10的盐酸溶液10mL浸出熔块,将此溶液与上述母液合并并加水定容至200mL。此溶液供ICP-AES在仪器工作条件下进行分析。绘制校准曲线时,加入纯铁和五氧化二钒作为基体,以消除基体干扰,然后加入上述8种元素的标准溶液,并按上述溶液最终稀释体积条件和仪器工作条件制作曲线(R大于0.999)。为验证所提出的分析方法的测定数据的精密度,约请了10个实验室对8个不同含量水平的钒铁样品对方法作协同试验,按GB/T 6379.2-2004所规定的方法求算了重复性标准偏差Sr和重复性限r,以及再现性标准偏差SR和再现性限R,并求得所测定的8种元素在各自的测定范围内的r与w之间和R与w之间的函数关系,说明该方法有较好的稳定性和准确性,而且证明此方法是可行的。     

基于Ce(IV)分光光度法的天然产物抗氧化活性的评价

基于在H2SO4,Na2SO4介质中稳定存在的Ce(IV)的还原,在320 nm时,采用紫外可见分光光度计测定Ce(IV)吸光度,建立还原率与样品浓度的剂量关系,以线性关系的斜率为主要评价指标,评价样品的抗氧化活性。结果表明:针对5种结构相近的黄酮化合物,抗氧化活性顺序为:槲皮素>山奈酚>木犀草素>芹菜素>黄芩素;针对中药植物湖北旋覆花,抱石莲和吉祥草的提取物,正丁醇、乙酸乙酯部位是抗氧化活性成分的主体部位,但在旋覆花和抱石莲中,正丁醇部位抗氧化活性更强,而在吉祥草中,乙酸乙酯部位明显强于正丁醇部位;此外,不同提取方法得到的提取物抗氧化活性不同,低温回流和超声提取均可提高效率,但超声提取的时间应该控制在30 min以内。本评价方法操作简单,结果稳定可靠,检测限低,适合于天然产物抗氧化活性植物及活性部位的快速筛选。     

Feasibility of Separation and Quantification of Inorganic Arsenic Species Using Ion-Exchange Membranes and Laser-Induced Breakdown Spectroscopy

Analytical methods for the determination of inorganic arsenic species have attracted much attention due to the high toxicity of these compounds and related legislative regulations for food. A new method for the separation and quantitation of As(III) and As(V) was developed using ion-exchange membranes and laser-induced breakdown spectroscopy (LIBS). Using the anion-exchange polymer membrane, As(V) was selectively collected on the membrane, and As(III) was filtered through the membrane. The separated As(V) on the membrane was directly determined by LIBS. The As(III) in the filtrate was subsequently oxidized to As(V) and collected by the membrane for LIBS analysis. The detection limit for As(V) was estimated to be 10?mg/kg. The recovery efficiencies for the arsenic species as standards were in the range of 97–99%. This method was applied for the analysis As-spiked water certified reference materials, and the results showed that the recovery for As(V) was 98.9%. This new speciation method is cost-effective, simple, and low labor-intensive for the quantitation of inorganic arsenic.     

Effect of ammonia carrier gas on the response of the flame ionization detector

The effect of using ammonia as a carrier gas on the response of the flame ionization detector (FID) has been investigated. It was found that the FID response, calculated as the effective carbon number (ECN), increased for all the compounds studied when ammonia, rather than helium, was used. The change was 0–0. 9 carbon atom for hydrocarbons, one carbon atom for alcohols and diphenyl ether, and 0.4–1 carbon atom for phenols and ketones. The increase in ECN was larger for amines (0. 8–5 carbon atoms), but these numbers also reflected an improvement in chromatographic performance as a result of reduced adsorption on the column. The largest change in signal-to-noise ratio, a six-fold increase, was obtained for octyl-amine; ratios for hexyl methyl ketone, diisobutyl ketone, dihexyl-amine, dibutylamine, and N-methyloctylamine increased by a factor of 2–3 when ammonia was used as carrier gas. To determine the extent to which the effect on detector response was solely attributable to ammonia, a mixture of 5 % ammonia in nitrogen was used as detector make-up gas with helium as carrier gas. Under these conditions the noise in the FID increased but for most of the compounds studied the signal-to-noise ratio also increased.