微波辐射对浆态床合成甲醇CuO/ZnO/Al2O3催化剂前驱体晶相转变的影响

在微波辐射条件下,对CuO/ZnO/Al2O3催化剂的沉淀母液进行老化,通过XRD、TG、H2-TPR,FTIR、HR-TEM和XPS对前驱体及催化剂微观结构的进行表征,探讨了CuO/ZnO/Al2O3催化剂前驱体晶相转变过程中微波辐射的作用。结果表明,微波辐射有利于Cu2+取代Zn5(CO3)2(OH)6中Zn2+的同晶取代反应。微波辐射的老化过程中,首先发生Cu2+取代Zn5(CO3)2(OH)6中Zn2+生成(Cu,Zn)5(CO3)2(OH)6的同晶取代反应,并于1.0 h内基本完成;随着老化时间继续延长,主要进行Zn2+取代Cu2(CO3)(OH)2中Cu2+生成(Cu,Zn)2(CO3)(OH)2的同晶取代反应,同时(Cu,Zn)5(CO3)2(OH)6进一步结晶。与常规老化1 h制备的前驱体相比,微波辐射老化1.0 h制备的前驱体含有较多的(Cu,Zn)5(CO3)2(OH)6物相,有助于增强焙烧后CuO/ZnO/Al2O3催化剂中CuO-ZnO协同作用,提高表面铜含量,进而提高CuO/ZnO/Al2O3催化剂在浆态床合成甲醇的催化活性和稳定性,在400 h浆态床合成甲醇评价期间,甲醇时空收率最大达318.9 g.kg-1.h-1,失活率仅为0.11%.d-1。     

前驱体物相转变对浆态床合成甲醇催化剂活性的影响

采用并流共沉淀法, 通过考察老化温度, 研究CuO/ZnO/Al₂O₃催化剂前驱体晶相及组成的变化对浆态床催化合成甲醇的反应活性的影响. 结果表明, 前驱体的物相转变对浆态床合成甲醇活性影响显著, 单斜晶系锌孔雀石(Cu,Zn)₂CO₃(OH)2和斜方晶系绿铜锌矿(Cu,Zn)₅(CO₃)₂(OH)₆晶体是产生高活性催化剂的主要物相. 随着Cu²⁺/Zn²⁺进入Zn₅(CO₃)₂(OH)₆/Cu₂CO₃(OH)₂晶格, 离子同晶取代量增加, 催化剂前驱体中形成了固定铜锌比的锌孔雀石和绿铜锌矿物相. 焙烧后催化剂比表面积增大, CuO-ZnO固溶体协同作用加强, 浆态床催化合成甲醇的活性提高.     

Cu/Zn比对微波辐射老化制备CuO/ZnO/Al2O3催化剂结构和活性的影响

在微波辐射条件下, 对共沉淀法制备合成甲醇CuO/ZnO/Al₂O₃催化剂前驱体的母液进行老化, 通过改变Cu/Zn比, 研究了微波辐射对催化剂性能的影响, 并结合XRD, FTIR, DTG, H₂-TPR, XPS等表征手段, 探讨了微波辐射对前驱体物相组成及催化剂微观结构的影响. 结果表明: 在微波辐射老化条件下, Cu/Zn比对催化剂前驱体物相组成影响较大, 微波辐射有利于绿铜锌矿(Cu, Zn)₅(CO₃)₂(OH)₆晶相选择生成. 当Cu/Zn比为2.0时, 前驱体中含有较多的绿铜锌矿物相, 且结晶较好, 焙烧后形成的催化剂中CuO-ZnO协同作用较强, CuO分散性好, 导致H₂还原温度低, 在浆态床合成甲醇过程中表现出良好的催化活性和稳定性, 甲醇时空收率(STY)达到309.0 g•kg^－1•h^－1, 失活率仅为0.11%/d, 远优于常规水浴加热制备的催化剂.     

溶剂极性对微波辐射老化制备前驱体及CuO/ZnO/Al2O3催化剂结构的影响

在制备CuO/ZnO/Al2O3催化剂的老化过程中,采用微波辐射老化技术,着重研究了溶剂极性对前躯体物相组成,烧后CuO/ZnO/Al2O3催化剂结构及其在浆态床合成甲醇工艺中催化性能的影响。通过XRD、DTG、H2-TPR,FTIR、HR-TEM和XPS对前驱体及催化剂表征表明,沉淀母液在微波辐射条件下进行老化,溶剂的极性对前躯体物相组成及催化剂结构影响显著。随着溶剂极性的增大,Zn2+/Cu2+取代Cu2(CO3)(OH)2/Zn5(CO3)2(OH)6中Cu2+/Zn2+的取代反应增强,使得前躯体中(Cu,Zn)5(CO3)2(OH)6和(Cu,Zn)2(CO3)(OH)2物相的含量增多,结晶度提高,导致烧后CuO/ZnO/Al2O3催化剂中CuO-ZnO协同作用增强,且CuO晶粒减小,表面Cu含量增加,催化剂活性和稳定性提高。水溶剂的极性最大,制备的催化剂活性和稳定性最好,甲醇的时空收率(STY)和平均失活率分别为320 mg.g-1.h-1和0.11%.d-1。     

沉淀还原法制备高性能CO2加氢合成甲醇Cu/ZnO/Al2O3催化剂

由铜基催化剂催化CO2+H2合成甲醇是有效利用CO2的潜在途径[1～5]. 但传统的催化剂对该反应的催化活性及选择性均很低[3～5], 因而寻求具有高活性及高选择性的新型催化剂已成为重要研究课题[4,6]. Cu/ZnO系列催化剂的制备方法和助剂对催化剂的性质及CO2加氢合成甲醇的反应性能有显著影响[6～10], 传统的气相还原活化铜基催化剂的过程常伴随强烈的热效应, 导致催化剂活化过程存在耗时长及还原条件难以控制等问题[11]. 本文采用沉淀-还原法, 用KBH4溶液对新鲜制备的碳酸盐共沉淀进行液相化学还原处理, 直接得到高活性及高选择性的还原态Cu/ZnO/Al2O3甲醇合成催化剂, 并可通过改变催化剂表面Cu+/Cu0活性物种的相对比例来改善催化剂的活性及选择性.     

并流淤浆混合法制备铜基甲醇合成催化剂及助剂Al2O3的作用研究

采用并流淤浆混合法制备了一系列具有不同铜锌铝比的铜基甲醇合成催化剂CuO/ZnO/Al2O3，测试了其催化性能(甲醇收率和CO转化率)及物相结构，并对该制备方法进行评价。Cu∶Zn∶Al摩尔比为4∶5∶1 的铜基催化剂显示了最好的催化活性。通过对催化剂前驱物煅烧过程进行DTA分析及对前驱物进行XRD分析表明， 催化剂前驱物的物相与Al2O3的量有关。当Al2O3的量较低时，前驱物的物相以(Cu0.3 Zn0.7)5(CO3)2(OH)6为主；当Al2O3的量较高时，前驱物中物相(Cu0.3Zn0.7)5(CO3)2(OH)6的量下降，而物相Cu2CO3(OH)2的量增加。物相(Cu0.3 Zn0.7)5(CO3)2(OH)6对终态催化剂的活性是十分有利的 。     

浆态床合成甲醇CuO/ZnO/Al2O3催化剂的表面性质

采用并流共沉淀法制备了不同Cu/Zn摩尔比的CuO/ZnO/Al2O3催化剂,考察了其浆态床CO加氢合成甲醇的催化性能.通过N2吸附-脱附、X射线衍射、程序升温还原及X射线光电子能谱等方法对催化剂表面性质进行了表征.结果表明,催化剂具有体相和表面高分散两种不同还原性质的CuO,表面CuO的含量及其与ZnO的相互作用使催化剂活性增大.当催化剂中Cu/Zn≤1时,随着铜含量的增加,表面高分散的CuO量增加,CuO和ZnO之间相互作用增强,催化剂的活性也随之增大;当催化剂Cu/Zn>1时,增加的铜量主要体现为体相CuO含量的增加,且ZnO结晶度提高,CuO和ZnO之间的相互作用减弱,催化剂的活性随铜含量增大而减小.     

沉淀及老化温度对浆态床合成甲醇CuO/ZnO/Al2O3催化剂活性及稳定性的影响

利用浆态床反应器,考察了沉淀及老化温度对CuO/ZnO/Al₂O₃催化剂催化合成甲醇的活性及稳定性的影响,并用XRD、BET、FT-IR以及XPS等技术对前驱体及催化剂进行了表征。结果表明,前驱体物相主要以孔雀石(Cu₂(CO₃)(OH)₂)和类孔雀石((Cu,Zn)₂(CO₃)(OH)₂)为主,其中,70 ℃沉淀和80 ℃老化条件下制备的前驱体具有适当的结晶度,焙烧后的催化剂中CuO分布均匀,Cu元素的电子结合能位移最大,CuO与ZnO之间作用较强,催化剂的性能最佳,时空收率和失活率分别达到了153.3 g/(kg_cat·h)和1.44%/d。     

加料方式对CuO/ZnO/Al2O3系催化剂前驱体性质的影响

用XRD、TG-DTG、TPR技术研究了不同加料方式对CuO/ZnO/Al2O3系催化剂前驱体物相组成及其结晶情况的影响，用加压微反装置考察了催化剂合成甲醇反应活性。结果表明, 加料方式对Cu2+形成的中间化合物的物相组成及结晶度影响显著,对Zn2+及Al3+的沉淀物相的影响很小。不同加料方式对催化剂前驱体物相组成及催化剂性能的影响主要是形成的初始前驱体中Cu的物相及结晶度不同。正加法主要形成Cu2(OH)3NO3,并流法主要形成无定形Cu2CO3(OH)2,后者与Zn5(CO3)2(OH)6相互作用转化为(Cu,Zn)2CO3(OH)2和（Cu,Zn）5(CO3)2(OH)6，由它们分解形成的CuO-ZnO固溶体是合成甲醇反应的活性相。并流法能最大程度的形成CuO-ZnO固溶体，有利于CuO粒子的细化，其催化活性较好。     

浆态床中Cu/ZnO/Al_2O_3/ZrO_2+γ-Al_2O_3双功能催化剂一步法合成二甲醚

采用共沉淀法,制备了纤维状CD501甲醇合成催化剂,采用SEM、TEM、XRD和BET等手段对催化剂进行了表征;并将其进一步和γ-Al2O3进行混合,获得了Cu/ZnO/Al2O3/ZrO2+γ-Al2O3双功能催化剂,考察了其在浆态床中一步法合成二甲醚过程的催化特性。结果表明,相比商业催化剂(COM)和LP201催化剂,新型的CD501催化剂具有更大的比表面积和Cu/Zn分散性。对于浆态床中一步法合成二甲醚过程,采用CD501与γ-Al2O3双功能催化剂,相比采用COM或LP201与γ-Al2O3双功能催化剂,CO转化率提高了一倍,且经过270 h测试,CO转化率从61%降至57%,二甲醚时空产率从0.54 g/(g.h)降至0.48 g/(g.h),稳定性显著优于COM催化剂。当反应温度为250℃,压力为4.0 MPa,空速为3 000 mL/(g.h),氢碳比为1.0时,该催化剂应用在浆态床一步法合成二甲醚时,CO转化率为61%,DME时空产率达到0.54 g/(g.h)。     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

层状正极材料LiNi1/6Co1/6Mn2/3O2的制备及电池性能

0引言为解决目前日益严重的汽车尾气排放对城市空气造成污染问题,作为绿色能源的锂离子电池已成为动力电池的首选对象。国际上,高容量、大功率锂离子电池早于1995年已开始研制。1996年,我国天津电源研究所也进行了大容量锂离子蓄电池及电池组的探索[1]。目前,锂离子电池的正极材料是制约其大规模推广应用的关键。现研究的正极材料主要包括具有层状结构的LiCoO2,LiN iO2和LiM nO2及具有尖晶石结构的LiM n2O4等。其中LiC oO2作为目前唯一已经商业化的正极材料具有理论容量高、可循环性能好等优点,但因Co资源的相对缺乏导致其价格高昂。…     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

锂离子电池正极材料层状LiNi1/2Mn1/2O2的制备与表征

用一种简单的共沉淀法制备出了层状LiNi_1/2Mn_1/2O₂材料，并且用XRD、SEM、循环充放电、循环伏安(CV)和电化学阻抗谱(EIS)等方法对材料进行了表征测试。首先，用共沉淀法制备氢氧化镍和氢氧化锰的混合物;然后，对共沉淀溶液进行预氧化来制备前驱体;最后，用预氧化的前驱体合成了LiNi_1/2Mn_1/2O₂材料。SEM和XRD测试结果分别表明:LiNi_1/2Mn_1/2O₂材料是粒径范围在100～200 nm之间的球形粒子，并且具有非常好的层状结构。循环充放电表明:在空气中900 ℃下合成时间为9 h的材料，在充放电截止电压为2.8～4.6 V的情况下，经过40次循环，材料的容量可以稳定地保持在140 mAh·g^-1左右。循环伏安曲线表明:在锂的初始脱嵌和入嵌过程中存在不可逆相变。电化学阻抗谱测试表明LiNi_1/2Mn_1/2O₂具有很好的锂离子扩散能力。     

Calorimetric study and thermal analysis of [Gd4/3Y2/3(Gly)6(H2O)4](ClO4)6·5H2O and [ErY(Gly)6(H2O)4](ClO4)6·5H2O (Gly: glycin)

Two solid-state coordination compounds of rare earth metals with glycin, [Gd_4/3Y_2/3(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O and [ErY(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O were synthesized. The low-temperature heat capacities of the two coordination compounds were measured with an adiabatic calorimeter over the temperature range from 78 to 376 K. [Gd_4/3Y_2/3(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O melted at 342.90 K, while [ErY(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O melted at 328.79 K. The molar enthalpy and entropy of fusion for the two coordination compounds were determined to be 18.48 kJ mol⁻¹ and 53.9 J K⁻¹ mol⁻¹ for [Gd_4/3Y_2/3(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O, 1.82 kJ mol⁻¹ and 5.5 J K⁻¹ mol⁻¹ for [ErY(Gly)₆(H₂O)₄](ClO₄)₆·5H₂O, respectively. Thermal decompositions of the two coordination compounds were studied through the thermogravimetry (TG). Possible mechanisms of the decompositions are discussed.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

Catalytic oxidation of no to NO2 over Cr/TiO2 and Cu/TiO2 under oxidizing atmosphere

The catalytic activity of Cr/TiO₂ and Cu/TiO₂ for the oxidation of NO under an oxidizing atmosphere has been examined. Both catalysts had excellent ability for the oxidation of NO to NO₂ in the temperature range of 350–400°C.     

Reducibility of Mo species in Pt/MoO3 and PtMo/Al2O3 catalysis

Recucibility of Mo species in Pt/MoO₃ and PtMo/Al₂O₃ has been investigated by temperature-programmed reduction (TPR), temperature-programmed desorption of hydrogen (H₂-TPD) and temperature programmed electronic conductivity (TPEC) techniques. In Pt/MoO₃ at H₂ atmosphere, it was found by TPEC and TPR that, a slight amount of Pt could activate the transfer of the species and H atoms between H₂ and MoO₃, and thus accelerate the reduction of MoO₃. In PtMo/Al₂O₃, TPR and H₂-TPD revealed that the reduction of surface Mo species could also be facilitated by Pt. Two kinds of hydrogen molybdenum species were proposed on the surface of the catalyst after prereduction.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

Following the crystallisation of Bi2Mo2O9 catalyst by combined XRD/QuEXAFS

The formation ofβ-phase Bi₂Mo₂O₉ catalyst from a precursor precipitate has been studied using thein situ combined XRD/QuEXAFS technique and DSC during calcination. Accordingly the precursor was observed to undergo a number of changes in both the molybdenum (VI) coordination and long-range ordering during this heating. Initially the two other forms of bismuth molybdate (α-andγ-phases) were observed to form from the poorly crystalline precursor at about 230°C, however, theβ-phase eventually crystallised after prolonged heating at 560°C. Dedicated to Professor C N R Rao on his 70th birthday