二次纳米自组装大孔氧化铝贯穿孔道的NSA形成机理

采用纳米自组装法合成的大孔氧化铝催化材料FA-06,具有1.39 mL·g^-1的孔容、297 m²·g^-1的比表面积、32.4 nm的最可几孔径和81.85%的孔隙率,孔道集中分布于10~30 nm和30~60 nm的比例分别占35.61%和40.88%。GPC结果表明,对于形成反相超增溶胶束的高聚物RHP,可通过改变聚异丁烯马来酸酐(PIBSA)的量来控制其分散度和相对分子量,进而控制大孔氧化铝的孔道结构。TEM及SEM结果表明,纳米自组装氢氧化铝棒长600~800 nm,直径为250~300 nm,经550.0℃焙烧后,形成直径为150~300 nm,长度为400~600 nm的纳米氧化铝棒。从焙烧后的纳米自组装氢氧化铝的XRD结果证明了3种γ-Al₂O₃的前躯体完全转化为γ-Al₂O₃。结合TG的结果,表明在605.0℃时,拟薄水铝石完全转化为γ-Al₂O₃,总失重可达61.88%。基于以上实验结果,模拟了反向超增溶胶束、氢氧化铝及大孔氧化铝的分子自组装和纳米自组装的形成过程,并提出了纳米自组装大孔氧化铝贯穿孔道的NSA(Nano Self-Assembly)形成机理。     

面向异丁烷脱氢介孔γ-Al2O3基催化剂的合成及其高催化性能

采用溶剂蒸发自组装法调控载体形貌及孔道结构,成功制备了有序介孔氧化铝载体。以铬氧物种为活性组分,碱金属钾为助剂,采用浸渍法制备负载型催化剂,用于异丁烷催化脱氢反应,研究了反应温度、原料流速、催化剂粒径等因素对催化性能的影响。采用X射线粉末衍射、透射电子显微镜、N₂物理吸附、氢气程序升温还原及热重等表征方法探讨了载体形貌、孔道结构与催化性能的构效关系,结果表明,低温下有利于控制异丙醇铝的水解和缩合及介孔γ-Al₂O₃的研制。与常规的γ-Al₂O₃相比,所制备的介孔γ-Al₂O₃的有更大的比表面积和良好的有序性,在600℃、101.325kPa、GHSV=1 000 h^-1的条件下,10%（w/w）Cr₂O₃/γ-Al₂O₃催化剂性能最佳,异丁烷的转化率达63.1%,异丁烯的选择性达到85.5%。与传统的催化剂相比,介孔Cr₂O₃/γ-Al₂O₃催化剂具有大的比表面积,高度分散的活性组分,优良的催化性能和良好的抗积碳能力。     

改性硅藻土负载亚铁氰化铜复合物的制备及其对Cs+的吸附性能

采用水热法、以氯化铝为铝源对硅藻土(De)进行改性,通过浸渍法将亚铁氰化铜(KCuHCF)纳米颗粒负载于改性De表面,制备出γ-AlOOH/De-KCuHCF和γ-Al₂O₃/De-KCuHCF两种复合吸附剂,对所制备的吸附剂进行了表征,并研究了其对Cs⁺的吸附性能。结果表明,所制备吸附剂具有优异的Cs⁺吸附性能,γ-AlOOH/De-KCuHCF和γ-Al₂O₃/De-KCuHCF最高吸附容量分别可达75.44、84.02 mg·g^-1,γ-Al₂O₃/De-KCuHCF对模拟卤水中Cs⁺的吸附率高达97.55%;以3 mol·L^-1 NH₄NO₃为脱附剂,经3级连续脱附后,γ-Al₂O₃/De-KCuHCF的Cs⁺脱附率可达81.88%,经过5次吸附-脱附循环后仍保持了较高的吸附量。     

γ-AlOOH/Al2O3修饰硅藻土的制备与Cs+、Pb2+吸附性能

以结晶氯化铝(AlCl₃·6H₂O)作为铝源,十二烷基苯磺酸钠(SDBS)为模板剂,采用水热法在硅藻土盘上制备了束状纳米结构γ-AlOOH/Al₂O₃复合吸附剂。采用XRD、SEM、TEM、TG/DSC、N₂吸脱附等对样品进行了表征。研究了样品对¹³³Cs⁺及Pb²⁺的吸附能力。研究表明,样品γ-AlOOH/硅藻土、γ-Al₂O₃/硅藻土,对Cs⁺及Pb²⁺均具有良好的吸附性能,两者对Cs⁺的去除率分别为98.9%和99.6%;对Pb²⁺的最大吸附量分别为357.1、416.7 mg·g^-1。两种样品对Pb²⁺的吸附均符合Langmuir吸附模型。     

自组装型Pt/γ-Al2O3催化剂用于低温去除挥发性有机物

分别通过自组装法(AS)和浸渍法(WI)制备得到纳米催化剂Pt/γ-Al₂O₃-AS和Pt/γ-Al₂O₃-WI, 并用于评价甲苯、异丙醇、丙酮、乙酸乙酯等易挥发性有机物(VOCs)的氧化性能. 通过各种表征手段探究了催化剂形态、结构及表面性质与催化剂氧化活性的关系. 结果表明, Pt/γ-Al₂O₃-AS在低温下即可实现VOCs的完全氧化. 在气体浓度(体积分数)为1000×10^-6, 空速为18000 mL·g^-1·h^-1的条件下, 甲苯、异丙醇、丙酮、乙酸乙酯被Pt/γ-Al₂O₃-AS催化剂完全氧化的温度分别为130、135、145、215℃, 展现出了优异的氧化性能, 且具有很好的稳定性. 该催化剂较高的比表面积、较小的Pt纳米粒径、较好的Pt纳米颗粒分散度、更好的低温还原效果及丰富的表面羟基是具有较高催化活性的重要因素.     

Ni2+在γ-Al2O3上的分散状态及负载型Ni/γ-Al2O3催化剂的α-蒎烯加氢活性

用X-射线衍射(XRD)、紫外-可见漫散射光谱(UV-Vis DRS)、程序升温还原(TPR)、CO化学吸附和微反测试等方法研究了Ni²⁺在γ-Al₂O₃上的分散状态和负载型Ni/γ-Al₂O₃催化剂的α-蒎烯加氢催化活性。结果表明，当Ni²⁺负载量远低于其在γ-Al₂O₃载体表面分散容量时，Ni²⁺优先嵌入载体表面四面体空位，随着Ni²⁺负载量的增加，嵌入载体表面八面体空位Ni²⁺的比例增大。由于八面体Ni²⁺易被还原为金属态Ni⁰，NiO/γ-Al₂O₃样品的还原度随Ni²⁺负载量的增加而大幅度地增加，经氢还原所得Ni/γ-Al₂O₃催化剂的CO吸附量和α-蒎烯加氢催化活性大幅度增加。对La₂O₃助剂的作用进行了研究，结果表明分散在γ-Al₂O₃上的La³⁺物种可阻止Ni²⁺嵌入γ-Al₂O₃表面四面体空位，增大了八面体Ni²⁺物种所占比例，提高了催化剂的还原度，故Ni-La₂O₃/γ-Al₂O₃催化剂催化活性高于Ni/γ-Al₂O₃催化剂。     

γ-Al2O3表面原位合成Ni-Al-CO3LDHs研究

Ni-Al-CO₃LDHs/γ-Al₂O₃have been prepared using an in-situ synthesis technique. NH₃·H₂O was chosen as activation agent of Al on the γ-Al₂O₃surface as well as precipitant. Ni-Al-CO₃LDHs/γ-Al₂O₃was synthesized by controlling the reaction conditions such as temperature, concentration of Ni²⁺ and initial pH. The crystalline structure, chemical composition and porous structure were characterized by means of XRD, FT-IR, TG-DTA, ²⁷Al MAS-NMR and N₂ adsorption-desorption. The resulting sample of Ni-Al-CO₃LDHs/γ-Al₂O₃possesses higher specific area and narrower pore distribution, in which Ni-Al-CO₃LDHs are located on the surface of γ-Al₂O₃and share the same Al-O bonds with the γ-Al₂O₃lattice. Finally a possible structural model was proposed to account for the porous characters of Ni-Al-CO₃LDHs/γ-Al₂O₃.     

Al2O3催化剂结构对催化臭氧化活性的影响

以Al₂O₃为催化剂催化臭氧化处理邻苯二甲酸二甲酯. 通过XRD、比表面积、孔结构、FTIR和活性评价等方法对催化剂的物化性质及催化活性进行了研究, 考察了焙烧温度、成型粒径对催化剂活性的影响. 结果表明, Al₂O₃催化剂对臭氧化降解邻苯二甲酸二甲酯具有很高的催化活性, 反应120 min后, 总有机碳(TOC)的去除率从单独臭氧氧化的23.9%提高到55.1%; 焙烧温度对催化剂的活性具有很大的影响, 600 ℃催化剂催化活性最高; 随着焙烧温度的升高, Al₂O₃晶型经历了从γ-Al₂O₃到θ-Al₂O₃到α-Al₂O₃的转变, 催化剂的比表面积、焙烧得到的孔容逐渐变小, 晶体粒径变大, 表面•OH数量减少, 催化活性下降. Al₂O₃成型粒径的减小, 提高了催化剂的外比表面积, 减小了内部传质扩散的影响, 从而提高了催化活性.     

CO预处理对CuO/γ-Al2O3催化剂性能的影响

采用XRD，TPR，CO吸附in-situ IR，CO氧化反应等对CuO/γ-Al₂O₃催化剂经CO处理前后的结构、组成和催化性能进行了研究。结果表明，经CO在250 ℃下处理1 h后CuO/γ-Al₂O₃催化剂中出现了分散态Cu⁺物种，该物种的产生使催化剂的活性明显提高。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。