Ce0.5Zr0.5O2修饰的Ni/SiC、Fe/SiC和Co/SiC催化燃烧甲烷性能

以铈锆固溶体（Ce_0.5Zr_0.5O₂）修饰的高比表面积SiC为载体,采用两步浸渍法制备了Ni、Fe和Co基催化剂,研究了其在煤层气催化燃烧脱氧中的催化活性和稳定性. 利用X射线衍射（XRD）、X射线光电子能谱（XPS）、电感耦合等离子体质谱（ICP-MS）、高分辨透射电子显微镜（HRTEM）、比表面积（BET）、热重分析（TGA）和H₂程序升温还原（H₂-TPR）对催化剂进行了表征. 分析结果表明,Ni、Fe和Co部分进入Ce_0.5Zr_0.5O₂固溶体晶格内部,导致催化剂体相形成更多的缺陷;同时Ce_0.5Zr_0.5O₂固溶体有助于加速金属氧化物和金属之间氧化还原过程的进行,促进了氧吸附、传输和对甲烷的活化. 另外,SiC和Ce_0.5Zr_0.5O₂固熔体良好的抗积碳性能,有效避免了催化剂在富甲烷反应气氛中因积碳而失活,从而使三种催化剂均具有优良的催化燃烧脱氧活性和稳定性. 其中,Co/Ce_0.5Zr_0.5O₂/SiC活性最高,可在320 ℃活化催化甲烷,并在410 ℃实现完全脱氧.     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

V2O5/赤铁矿催化剂结构及其NH3选择性催化还原NOx性能

以水热合成针铁矿为前驱体浸渍偏钒酸铵,分别于300,400和500℃空气中焙烧,制备了不同活性组分负载量的V₂O₅/赤铁矿（V/H）催化剂,用于氨选择性催化还原（SCR）脱硝。采用X射线衍射、透射电子显微镜、比表面积分析仪、程序升温还原及程序升温脱附等方法对催化剂结构进行了表征,并用标气配制模拟烟气进行了脱硝实验。结果表明,300℃煅烧3%V/H催化剂当烟气温度为250-300℃时NO转化率均可达95%以上;当配气中单独加入水蒸气或低浓度SO₂（0.01%）时,V/H催化脱硝的活性不受影响;当系统加入高浓度的SO₂（0.03%与0.05%）或同时添加H₂O与SO₂时,SCR脱硝效率下降,其机制可能是SO₂在催化剂表面竞争吸附所致,停止添加后,催化活性迅速恢复。     

一个新的满足未来排放标准的摩托车尾气净化催化剂

采用共沉淀法制备CeO₂-ZrO₂-La₂O₃-PrO₂-Al₂O₃复合氧化物载体材料,以浸渍法制备了Pd-Rh,Pt-Rh和Pt-Pd-Rh型整体式催化剂. 用N₂吸附-脱附、程序升温还原、储氧量和X射线衍射对其进行了表征,并考察了老化前后催化剂的空燃比特性、空速特性和温度特性. 结果表明,在三种催化剂中,Pt-Pd-Rh型催化剂表现出更优异的性能. 在40000 h^-1空速下,新鲜Pt-Pd-Rh型催化剂对C₃H₈,CO和NO的起燃温度T₅₀分别为239,187和191 ℃,ΔT （T₉₀ - T₅₀）分别为21,3和3 ℃. 老化后,C₃H₈,CO和NO的T₅₀分别为298,203和223 ℃,ΔT分别为22,5和13 ℃,且老化前后空燃比窗口较宽,适合于未来排放标准的摩托车尾气净化.     

制备方法对Al2O3掺杂Pt/WO3-ZrO2催化剂上正庚烷异构化反应的影响

采用恒pH法和非恒pH法制备了Al₂O₃掺杂的Pt/WO₃/ZrO₂催化剂,并用N₂吸附-脱附、X射线衍射、紫外-可见漫反射、CO化学吸附、X射线光电子能谱、²⁷Al魔角旋转核磁共振和吡啶吸附红外等技术对催化剂进行了表征.结果表明,相比于非恒pH法制备的催化剂,恒pH法制备的催化剂具有较高的比表面积和Pt分散度,在H₂气氛中产生更多的B酸位,从而表现出更高的催化正庚烷临氢异构化反应活性; 在200℃和质量空速0.9h^-1的反应条件下,正庚烷转化率达70.0%,明显高于非恒pH法制备的催化剂(43.5%).     

碱土金属对ZrO2-Al2O3及其负载Pd-Rh密偶催化剂的影响

采用胶溶法制备了一系列碱土金属改性的ZrO₂-Al₂O₃, 并以其为载体采用等体积浸渍法制备了Pd-Rh密偶催化剂. 采用低温N₂吸附-脱附、X射线衍射(XRD)、氨气程序升温脱附(NH3-TPD)对载体样品进行了表征. 结果表明, 碱土金属的添加增大了ZrO₂-Al₂O₃的比表面积, Sr-Zr-Al样品经1000 °C焙烧5 h后具有最大的比表面积, 为164 m²·g^-1. 对催化剂进行了H₂程序升温还原(H₂-TPR)、X射线光电子能谱(XPS)和活性表征, 考察了催化剂对C₃H₈的转化活性. 测试结果表明, 添加碱土金属能有效提高催化剂上丙烷的转化活性.     

Se掺杂WO3·0.5 H2O/g-C3N4光电催化剂的析氢反应性能

以二氰二胺、硒粉和钨酸钠为前驱体,采用一锅法成功制备出Se掺杂WO₃·0.5 H₂O/g-C₃N₄(Se/WCN)催化剂。并采用X射线衍射仪(XRD)、场发射扫描电子显微镜(FE-SEM)和 X 射线光电子能谱(XPS)对样品的物相结构、形貌及化学组成进行表征。与原始的 WO₃和 g-C₃N₄相比,Se/WCN 催化剂的起始电位降到了-0.75 V(vs RHE),电流密度高达 70 mA·cm^-2,表现出更高的电催化活性。而光照后,Se/WCN 的催化性能进一步提升,起始电位从-0.75 V(vs RHE)降至-0.65 V(vs RHE),电荷转移电阻由371.4 Ω减小到310.0 Ω。     

Ni/SiO2-ZrO2催化剂焙烧温度对其催化愈创木酚加氢脱氧性能的影响简

采用化学沉淀法合成了SiO₂-ZrO₂复合氧化物载体,并以浸渍法制备了Ni/SiO₂-ZrO₂双功能催化剂,考察了焙烧温度对催化剂结构及其催化愈创木酚加氢脱氧制环己烷性能的影响. 结果表明,经500℃焙烧催化剂的加氢脱氧活性最高,在Ni金属中心和SiO₂-ZrO₂载体材料的协同作用下,愈创木酚转化率为100%,环己烷选择性为96.8%. 对催化剂进行N₂物理吸附、H₂化学吸附、X射线衍射分析、H₂程序升温还原、NH₃程序升温脱附与Raman光谱等表征后发现,合成的SiO₂-ZrO₂为无定形的酸碱两性氧化物;经500℃焙烧的催化剂样品的有效比表面积和孔体积均明显增大,表面酸量最多,硝酸镍分解成小颗粒的NiO较易被H₂还原,这些特性是该催化剂样品具有高效加氢脱氧活性的原因.     

Zr 改性MnOx/MWCNTs催化剂的结构特征与低温SCR活性

以ZrO（NO₃）₂·2H₂O为前驱体对多壁碳纳米管（MWCNTs）进行了改性并负载MnO_x制备了MnO_x/ZrO₂/MWCNTs 催化剂. 考察了Zr 对催化剂低温选择性催化还原（SCR）反应活性的影响,并通过多种分析手段对催化剂的结构进行了表征. 结果表明Zr 的添加对催化剂的低温SCR活性具有显著的促进作用,当Zr 负载量为30%时,催化剂活性最佳. X射线衍射（XRD）、拉曼（Raman）光谱、透射电镜（TEM）、N₂吸附-脱附的表征结果分析表明,适量的Zr 改性促进了MnO_x在载体表面的分散,增强金属氧化物与MWCNTs 之间的作用,也能增加催化剂的比表面积、孔容和孔径. X 射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和NH₃程序升温脱附（NH₃-TPD）的分析结果则显示,Zr 能提高催化剂表面化学吸附氧浓度,促进Mn³⁺转化为Mn⁴⁺,从而使催化剂表面的活性位点增多,氧化还原能力增强,同时还提高了催化剂表面酸性位点的数量和强度,促进了NH₃的吸附,是MnO_x/ZrO₂/MWCNTs 催化剂低温SCR活性提高的主要原因.     

用原位红外技术研究Ag-MoO3/ZrO2催化丙烯气相环氧化反应

制备了对丙烯直接气相环氧化具有优良催化性能的Ag-MoO₃/ZrO₂催化剂, 采用原位FT-IR技术研究了丙烯、环氧丙烷及丙烯和氧气混合气在载体和催化剂上的吸附及反应行为. 研究表明, 丙烯在ZrO₂载体和20%Ag-4%MoO₃/ZrO₂催化剂上吸附后, 均不发生化学反应, 而环氧丙烷在ZrO₂载体上吸附后于400 ℃发生开环反应, 在20%Ag-4%MoO₃/ZrO₂催化剂上吸附后于300 ℃发生开环反应. 当丙烯和氧气混合气在ZrO₂载体上共吸附后, 随着反应温度从室温升高至400 ℃, 二者开始反应生成CO₂和H₂O; 混合气在20%Ag-4%MoO₃/ZrO₂催化剂上共吸附后于350 ℃开始反应. 对比非负载型Ag-MoO₃催化剂的研究结果可见, ZrO₂载体的存在使催化剂的活性下降的同时, 提高了对产物环氧丙烷的选择性.     

Catalytic Combustion of Ethyl Acetate over Al2O3- Ce0.5Zr0.5O2 Supported Metal Oxide Catalysts

The catalysts for the combustion of ethyl acetate were prepared using Fe, Co, Cu, Cr, and Mn metal oxide as active components supported on Al₂O₃-Ce_0.5Zr_0.5O₂ mixed oxides and characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), oxygen storage capacity measurement, BET surface area, XPS measurement, and activity test. According to the results of characterization, it was found that Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) catalysts presented excellent activity for the catalytic combustion of ethyl acetate, because of the more reducible species and high reducibility of the catalysts. For ethyl acetate oxidation, more than 99% conversion was achieved at 245 °C over catalysts Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio), indicating that the catalysts had great potential for wide use.     

Zr0.5Ti0.5O2的添加对超临界裂解RP-3催化剂性能的影响

采用共沉淀法制备了Zr_0.5Ti_0.5O₂载体材料,将其掺杂在CeO₂-Al₂O₃ (CA)基催化剂中, 并对其催化活性进行了超临界裂解测试, 采用全自动吸附仪、X射线衍射(XRD)、透射电镜(TEM)、程序升温脱附(TPD)等方法对催化剂进行了表征. 实验结果表明, 催化剂能够明显降低裂解反应的温度, 600 ℃ CA基催化剂产气率是热裂解的2.8倍, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂是热裂解的4.0倍, 650 ℃时, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂热沉提高了0.55 MJ·kg^-1. BET结果表明, 掺杂Zr_0.5Ti_0.5O₂载体后催化剂出现双孔结构, 部分小孔的出现使得乙烯的选择性提高; NH₃-TPD结果表明, 掺杂Zr_0.5Ti_0.5O₂载体材料后, 催化剂强酸位的酸量增加了4.0倍,催化剂表现出更强的表面酸性和更集中的强酸酸中心密度, 有利于裂解多产烯烃.     

Excellent complete conversion activity for methane and CO of Pd/TiO2-Zr0.5Al0.5O1.75 catalyst used in lean-burn natural gas vehicles

Palladium catalysts are supported on TiO₂, ZrO₂, Al₂O₃, Zr_0.5Al_0.5O_1.75 and TiO₂-Zr_0.5Al_0.5O_1.75 prepared by co-precipitation method, respectively. Catalytic activities for methane and CO oxidation are evaluated in a gas mixture that simulated the exhaust from lean-burn natural gas vehicles (NGVs). Pd/TiO₂-Zr_0.5Al_0.5O_1.75 performs the best catalytic activity among the tested five catalysts. For CH₄, the light-off temperature (T₅₀) is 254 °C, and the complete conversion temperature (T₉₀) is 280 °C; for CO, T₅₀ is 84 °C, and T₉₀ was 96 °C. Various techniques, including N₂ adsorption-desorption, X-ray diffraction (XRD), H₂-temperature-programmed reduction (H₂-TPR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) are employed to characterize the effect of supports on the physicochemical properties of prepared catalysts. N₂ adsorption-desorption and SEM show that TiO₂-Zr_0.5Al_0.5O_1.75 expresses uniform nano-particles and large meso-pore diameters of 26 nm. H₂-TPR and XRD indicate that PdO is well dispersed on the supports and strongly interacted with each other. The results of XPS show that the electron density around PdO and the proportion of active oxygen on TiO₂-Zr_0.5Al_0.5O_1.75 are maxima among the five supports.     

Pd catalysts supported on modified Zr0.5Al0.5O1.75 used for lean-burn natural gas vehicles exhaust purification

Composite supports Zr0.5Al0.5O1.75 modified by metal oxides,such as La2O3,ZnO,Y2O3 or BaO,were prepared by co-precipitation method,and palladium catalysts supported on the modified composite supports were prepared by impregnation method.Their properties were characterized by X-ray diffraction(XRD),NH3 temperature-programmed desorption(NH3-TPD),H2 temperature-programmed reduction(H2-TPR),N2 adsorption/desorption,and CO-chemisorption.The catalytic activity and the resistance to water poisoning of the prepared Pd catalysts were tested in a simulated exhaust gas from lean-burn natural gas vehicles with and without water vapor.The results demonstrated that the modified supports had an apparent effect on the performance of Pd catalysts,compared with the Pd catalyst supported on the unmodified ZrAl.The addition of ZnO or Y2O3 promoted the conversion of CH4.In the absence of water vapor,Pd/ZnZrAl exhibited the best activity for CH4 conversion with the light-off temperature(T50) of 275℃ and the complete conversion temperature(T90) of 314℃,respectively.However,in the presence of water vapor,Pd/YZrAl was the best one over which the light-off temperature(T50) of methane was 339℃ and the complete conversion temperature(T90) was 371℃.These results indicated that Pd catalyst supported on the modified composite ZrAl support showed excellent catalytic activity at low temperature and high resistance to H2O poisoning for the exhaust purification of lean-burn natural gas vehicles.     

表面助剂改性对Cu/ZnO/Al2O3甲醇合成催化剂性能的影响

采用共沉淀-后浸渍方法制备了表面助剂改性的Cu/ZnO/Al₂O₃ (CZA)甲醇合成催化剂, 在固定床反应器上以合成气为原料分别考察了三种助剂(Zr、Ba和Mn)对CZA催化剂性能的影响; 以Zr为助剂时反应温度的影响; 并进行了催化稳定性试验. 利用粉末X射线衍射(XRD)、低温氮气吸脱附(N₂-sorption)、氧化亚氮(N₂O)反应吸附技术、X射线光电子能谱(XPS)、氢气程序升温吸脱附(H₂-TPD)、扫描电子显微镜(SEM)和高分辨透射电子显微镜(HR-TEM)技术对催化剂进行了表征.结果显示: 以Zr或Ba作为助剂能够明显提高CZA催化剂耐热前后的甲醇时空收率(STY); Mn的引入降低了CZA催化剂的耐热前活性; Zr的引入降低了CZA催化剂最高活性温度点, 增强了CZA催化剂的催化稳定性; 还原态CZA催化剂表面Cu⁰和ZnO都能吸附活化氢气, Cu⁰与ZnO的强相互作用有利于提高催化剂的性能, 耐热后催化剂性能的降低归因于Cu晶粒的长大. 在实验和表征结果基础上,提出了CZA催化剂上合成气制甲醇的“双向同步催化反应历程”.     

Promotional effect of cobalt addition on catalytic performance of Ce<Subscript>0.5</Subscript>Zr<Subscript>0.5</Subscript>O<Subscript>2</Subscript> mixed oxide for diesel soot combustion

A series of Co-modified Ce_0.5Zr_0.5O₂ catalysts with different concentrations of Co (mass %: 0, 2, 4, 6, 8, 10) was investigated for diesel soot combustion. Ce_0.5Zr_0.5O₂ was prepared using the coprecipitation method and Co was loaded onto the oxide using the incipient wetness impregnation method. The activities of the catalysts were evaluated by thermogravimetric (TG) analysis and temperature-programmed oxidation (TPO) experiments. The results showed the soot combustion activities of the catalysts to be effectively improved by the addition of Co, 6 % Co/Ce_0.5Zr_0.5O₂ and that the 8 % Co/Ce_0.5Zr_0.5O₂ catalysts exhibited the best catalytic performance in terms of lower soot ignition temperature (T_i at 349°C) and maximal soot oxidation rate temperature (T_m at 358°C). The reasons for the improved activity were investigated by X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), H₂ temperature-programmed reduction (H₂-TPR), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). These results revealed that the presence of Co could lower the reduction temperature due to the synergistic effect between Co and Ce, thereby improving the activity of the catalysts in soot combustion. The 6 % Co catalyst exhibited the best catalytic performance, which could be attributed to the greater amounts of Co³⁺ and surface oxygen species on the catalyst.     

国产航空煤油裂解催化剂Pt/ZrxTixAl1-2xO2的性能

采用共沉淀法制备了一系列Zr_xTi_xAl_1-2xO₂复合氧化物载体材料,考察了其作为裂解催化剂载体对航空煤油裂解反应的影响.?采用全自动吸附仪、X射线衍射、扫描电镜/能谱仪联用、NH₃-程序升温脱附等手段对催化剂进行了表征.?结果表明,当ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂具有最大的比表面积和孔容;具有最强的表面酸性和最集中的强酸中心密度,且具有良好的再生功能.?实验结果表明,载体ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂上650?℃裂解产气量较热裂解提高了2.1倍,700?℃时提高1.4倍.?另外,该系列载体材料经1000?℃焙烧5?h后,所制得的催化剂几乎失去了催化活性.     

Selective catalytic reduction of NO over metal oxide or noble metal-doped In2O3/Al2O3 catalysts by propene in the presence of oxygen

The activities of metal oxide CuO, SnO₂, CoO, Ag₂O, ZnO or noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts for selective catalytic reduction of NO by propene were investigated. The temperature windows for NO reduction over noble metal-doped In₂O₃/Al₂O₃ catalysts were shifted and broaden slightly compared with single component catalyst alone. This revised version was published online in June 2006 with corrections to the Cover Date.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.