炭载体改性对炭载Pd催化剂电催化性能的影响

研究了硝酸和氨水改性处理对活性炭表面基团、炭载Pd纳米粒子的形态及其对甲酸氧化电催化性能的影响.傅里叶变换红外(FT-IR)光谱、X射线光电子能谱(XPS)及Boehm滴定结果表明,硝酸和氨水处理分别增加了活性炭表面含氧基团和含氮基团的含量.透射电镜(TEM)及电化学测试显示,活性炭经硝酸处理后,表面负载的Pd粒子粒径降低,催化剂对甲酸氧化活性和稳定性提高.进一步用氨水处理后,Pd粒子的粒径没有明显变化,但催化剂中Pd0的含量增加,催化剂性能进一步提高.     

碳纳米管表面修饰程度对碳纳米管载Pt电催化性能的影响

比较了用不同温度的浓HNO₃处理的碳纳米管(CNTs)作载体的Pt(Pt/CNTs)对甲醇氧化的电催化活性. 结果表明浓HNO₃处理使CNTs表面修饰上的含氧基团对CNTs上沉积Pt粒子的平均粒径有较大影响. 表面修饰程度适当时, 制得的Pt/CNTs中Pt粒子较小, 因此, 对甲醇氧化的电催化活性较高. 而表面修饰程度过大, 易使Pt粒子团聚, 从而降低Pt/CNTs催化剂对甲醇氧化的电化学活性.     

Pd/Ni异结构纳米催化剂的制备及其对甲酸氧化的电催化

通过两步还原法制备了Pd/Ni双金属催化剂.由于金属Pd原子在先行还原的Ni纳米粒子表面的外延生长以及其在Ni表面及Pd表面生长表现出的吉布斯自由能差异,最终导致了异结构Pd/Ni纳米粒子的形成.高分辨电子透射显微镜结果证实了异结构的存在,然而X射线衍射测量表明Pd/Ni纳米粒子具有类似于Pd的面心立方结构.制备的Pd/Ni纳米粒子与同等条件下合成的Pd纳米粒子相比对甲酸氧化呈现了更高的电催化活性,而且电催化稳定性也要明显优于纯Pd纳米粒子,证明Pd/Ni双金属催化剂是可选的直接甲酸燃料电池阳极催化剂.双金属催化剂对甲酸氧化电催化活性和稳定性增强可能是Ni原子的修饰改变了Pd粒子表面配位不饱和原子的电子结构所致.     

Pd/PVP-MWCNTs电极对甲酸氧化的电催化性能

用聚乙烯吡咯烷酮（PVP）修饰的多壁碳纳米管（MWCNTs）作为Pd纳米粒子的载体,制得了Pd/PVP-MWCNTs催化剂并研究了其对甲酸氧化的电催化性能. 红外光谱仪（FTIR）和透射电镜（TEM）观测结果表明,Pd/PVP-MWCNTs催化剂中的Pd纳米粒子平均粒径小、分散性好. 因此,Pd/PVP-MWCNTs催化剂对甲酸电氧化有很好的电催化性能.     

还原态氧化石墨烯载Pd纳米催化剂对甲酸氧化的电催化性能

采用改进的Hummers法氧化石墨后,对其超声剥离成氧化石墨烯水溶液,继之通过乙二醇还原Pd金属离子和氧化石墨烯,得到了还原态氧化石墨烯（RGO）负载Pd纳米催化剂,并用于甲酸的电催化氧化.透射电子显微镜和X射线衍射结果显示：负载于RGO上的Pd粒子平均粒径为3.8nm,其优先在RGO的褶皱和边缘处生长.电化学测试表明：RGO上残存的含氧基团降低了Pd催化剂受CO毒化的程度,Pd/RGO催化剂表现出了较商业化Pd/C更高的电催化活性和更好的稳定性.     

EDTA对活性炭的功能化处理及其对炭载Pd催化剂电催化性能的影响

采用乙二胺四乙酸(EDTA)对活性炭进行功能化处理, 研究了其对表面基团、炭载Pd 纳米粒子结构及Pd催化剂电催化性能的影响. 傅里叶变换红外(FTIR)光谱和X射线光电子能谱(XPS)表征表明, EDTA处理在炭表面引入了含氮基团. X射线粉末衍射(XRD)光谱、透射电镜(TEM)和电化学测试结果显示, 活性炭经EDTA处理后, 负载的Pd粒子粒径虽有所增大, 但由于炭载体与Pd粒子相互作用的增强, Pd利用率增加, 催化剂对甲酸氧化的活性和稳定性均显著提高. 电化学阻抗谱(EIS)分析进一步揭示, 甲酸在该催化剂电极上的电氧化反应具有较低的电荷传递电阻.     

碳纳米纤维在浓硝酸-浓硫酸溶液中表面氧化对其负载的Pd-Pt催化剂颗粒分散状态的影响

摘要用混合的浓硝酸和浓硫酸在不同温度下氧化处理催化生长的碳纳米纤维. 利用X射线衍射、 N2物理吸附、 FTIR和离子交换研究了氧化处理对碳纳米纤维织构性质和表面含氧基团生成的影响. 采用等体积浸渍法制备碳纳米纤维负载Pd-Pt催化剂, 并利用高分辨电镜和脉冲H₂化学吸附对Pd-Pt金属颗粒的分散状况进行了研究. 结果表明, 经过氧化处理的碳纳米纤维表面生成了含氧基团, 生成量随着处理温度的升高而升高, 负载的Pd-Pt催化剂的分散程度也随着表面含氧基团浓度的增大而提高, 同时对后者的作用机理进行了讨论.     

纳米三氧化钨修饰碳纳米管载铂催化剂对甲醇氧化的电催化性能

采用表面修饰技术将碳纳米管(CNT)表面羧基化, 通过羧基将钨离子基团修饰到碳纳米管的外表面, 再通过高温焙烧处理将钨离子基团氧化成WO₃, 成功合成了纳米WO₃/CNT复合物, 进一步还原Pt 的前驱体而得到Pt-WO₃/CNT复合催化剂. 采用X射线粉末衍射(XRD)和透射电镜(TEM)对样品的形貌和晶型结构进行了表征, 结果表明, Pt纳米粒子为面心立方晶体结构, 均匀地分布在WO₃修饰的碳纳米管表面. 采用循环伏安(CV)和计时电流法研究了在酸性溶液中Pt-WO₃/CNT催化剂对甲醇的电催化氧化活性, 结果表明WO₃修饰的碳纳米管载铂催化剂比用混酸处理的碳纳米管载铂催化剂对甲醇呈现出更高的电催化氧化活性和更好的稳定性.     

中空介孔三氧化钨微球载钯催化剂的甲酸氧化电催化性能(英文)

采用喷雾干燥法和焙烧处理制备中空介孔三氧化钨微球(HMTTS),在其表面进一步负载活性成分Pd,得到纳米Pd/HMTTS复合催化剂.采用X射线粉末衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)等对催化剂的形貌和晶型结构进行了表征.结果表明,Pd纳米粒子为面心立方晶体结构,均匀地分布在HMTTS表面.采用循环伏安和计时电流法研究了在酸性溶液中Pd/HMTTS催化剂对甲酸的电催化氧化性能,结果表明Pd/HMTTS催化剂比普通的三氧化钨载钯催化剂(Pd/WO3)对甲酸呈现出更高的电催化氧化活性和稳定性.HMTTS独特的中空介孔结构和表面特性以及氢溢流效应有利于甲酸在钯表面的直接脱氢氧化过程的发生.     

TiO2纳米棒载Pd催化剂的制备及其对甲酸的电催化氧化

利用水热合成和无机溶胶法,分别制备了具有棒状(TiO2-R)和无规则结构(TiO2-I)的锐钛矿相TiO2,并以之为载体制备得到Pd/TiO2电催化剂.循环伏安测试显示,与无规则TiO2相比,具有棒状结构的TiO2载Pd催化剂对甲酸氧化的电催化性能提高了70%;计时电流测试显示,运行3000 s后,甲酸在棒状TiO2载Pd催化剂上的氧化电流是无规则TiO2载Pd催化剂的16倍.其原因可能与TiO2纳米棒拥有更好的电子传导性且表面拥有较多的活性含氧基团有关,从而能够有效提高催化剂对甲酸氧化的电催化活性和抗毒化性能.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.