ZSM-5分子筛催化苯与甲醇烷基化反应研究进展

我们综述了近年来苯和甲醇烷基化反应研究取得的进展.重点从ZSM-5催化剂的Si/Al、晶粒尺寸、改性等方面介绍了苯和甲醇烷基化催化剂的研究进展,总结并展望了苯和甲醇烷基化反应的研究方向,为ZSM-5分子筛催化剂的改性和苯-甲醇烷基化反应工艺创新提供参考.     

HF改性的Pt/ZSM-5催化剂在苯和甲醇烷基化反应中的应用

以HF改性的Pt/ZSM-5为催化剂,研究了其在苯和甲醇烷基化反应的应用,并用XRD、NH₃-TPD、BET等表征方法研究了改性前后催化剂酸性和孔结构变化。 结果表明,经HF改性后,Pt/ZSM-5催化剂的酸性增强、酸量增加,苯和甲醇烷基化反应性能明显提升。 3%HF-0.2%Pt/ZSM-5催化剂催化苯和甲醇烷基化反应时,甲苯和二甲苯选择性达到92.20%。 但是,HF负载量大于6%时,HF脱除的部分骨架硅和骨架铝会堆积在催化剂孔道内部,限制了反应物和产物的扩散,造成其催化性能下降。 通过计算得到了HF改性的Pt/ZSM-5催化剂上苯和甲醇烷基化反应的活化能为118 kJ/mol。     

ZSM-22分子筛的合成、表征及烷基化性能研究

通过不同合成方法制备聚束状、粗棒状和细棒状ZSM-22分子筛,采用XRD、SEM、BET、MAS NMR、NH_3-TPD及PyFTIR等表征手段对分子筛的形貌、织构、硅铝配位环境及酸性进行研究。以甲苯-甲醇烷基化制备对二甲苯为探针反应,考察不同形貌ZSM-22分子筛催化剂的催化性能。结果表明,不同形貌ZSM-22分子筛的晶胞参数、织构、硅铝配位环境及酸性等存在明显差异。聚束状ZSM-22分子筛由于各束之间的相互作用导致Si(4Si)配位结构发生变化,Al原子的嵌入导致T3和T4比例较高、T2较少,并表现出更多的L酸中心。在380℃反应温度下,聚束状ZSM-22分子筛催化剂在甲苯-甲醇烷基化反应转化率为16.7%时,对二甲苯选择性达到76.1%。     

不同粒径ZSM-5分子筛在苯与甲醇烷基化反应中催化性能及反应条件优化

采用水热合成法合成了不同粒径的ZSM-5分子筛催化剂,系统考察了分子筛粒径变化对苯与甲醇烷基化反应的影响。研究结果表明,随着ZSM-5分子筛粒径增大,不但苯的转化率和二甲苯选择性降低,而且催化剂稳定性明显下降。其中,粒径为0.25 μm的ZSM-5分子筛在苯烷基化反应中的催化性能最佳,且催化剂稳定性最好。另外,采用拉曼光谱和热重等方法对催化剂积碳物种和失活机理进行了深入研究,发现催化剂失活主要是由于反应过程中生成的大分子稠环芳烃堵塞了分子筛孔道并覆盖活性位点造成的。最后,考察了反应温度、原料组成及空速对苯烷基化反应的影响并优化出最佳的苯烷基化反应条件。     

甲苯-甲醇侧链烷基化合成苯乙烯的研究进展

甲苯-甲醇侧链烷基化合成苯乙烯具有极高的工业应用前景和学术研究意义.我们介绍了甲苯与甲醇侧链烷基化反应制苯乙烯的课题背景,总结了改性X型分子筛、复合型分子筛、多孔碳和金属氧化物以及其它类型催化剂在甲苯-甲醇侧链烷基化反应中的应用状况,分析了其反应机理及甲醛深度分解的原因以及目前催化剂的不足,并提出了可能的改进方案.最后对该领域的今后研究重点进行了展望,为提升甲苯与甲醇侧链烷基化催化剂的活性、选择性及使用寿命等相关研究提供参考.     

改性ZSM-5-SBA-15及甲苯甲醇烷基化性能研究

通过浸渍法对ZSM-5进行金属M(M为Mg、Ni、Sr)改性,合成法制备了M-ZSM-5-SBA-15复合分子筛,采用XRD、N2吸附-脱附、FT-IR、NH3-TPD和Py-FTIR等技术对样品进行表征,考察了HZSM-5的硅铝比、不同金属对ZSM-5-SBA-15复合分子筛烷基化性能的影响。结果表明,HZSM-5的硅铝比为80时,ZSM-5-SBA-15复合分子筛的烷基化性能较好,Sr的引入钝化了ZSM-5-SBA-15(80)的强B酸中心,降低了B酸与L酸的比值,Sr-ZSM-5-SBA-15(80)的甲苯甲醇烷基化性能明显提高,甲苯转化率为30.15%,对二甲苯选择性为77.41%。     

ZSM-5酸改性对甲醇芳构化性能的影响

利用硝酸、草酸和酒石酸溶液对ZSM-5分子筛进行改性,并采用XRD、SEM、NH₃-TPD、XRF、²⁷Al MAS NMR、吡啶吸附红外光谱和N₂吸附-脱附对ZSM-5分子筛结构、酸量、比表面积及孔体积等物化性质进行表征分析。在反应温度为422℃,甲醇质量空速为4.74 h^-1的条件下,考察了ZSM-5分子筛的催化活性。结果表明,采用不同酸改性ZSM-5分子筛,影响了分子筛的比表面积、酸性及孔体积,从而改变了催化剂的催化性能。在甲醇芳构化（MTA）反应中,酸改性后的分子筛表现出良好的催化活性,且草酸改性后的催化剂表现出较高的催化活性及选择性,反应8 h时,芳烃及BTX收率分别达到57.40%和39.40%。     

NaOH改性ZSM-5分子筛在苯、甲醇烷基化反应中的应用

用NaOH溶液对高硅ZSM-5分子筛进行处理,考察其应用于苯-甲醇烷基化反应过程的最佳处理条件,并用XRD、SEM、XRF、NH3-TPD、TPO、BET等手段对试样进行表征。结果表明,NaOH在脱除分子筛硅物种的同时,也会脱出晶粒表面附着物,暴露出更多的酸性位,形成一定量的介孔,进而影响苯-甲醇烷基化性能。当NaOH处理量为2.4 mmol/gcat时,在液体积空速为85 h-1下,烷基化反应中苯的转化率达到38%,相比处理前提高了近16%,且积炭量低,稳定性好。     

在稀土改性的ZSM-5沸石催化剂上甲苯歧化选择生成对二甲苯的研究

本文研究了ZSM-5沸石催化剂用稀土元素(La~(3 )、Ce~(3 )、Pr~(3 )、Nd~(3 ))以及混合稀土浸渍改性处理后对甲苯歧化反应的催化性能。实验结果表明:上述四种稀土元素改性处理后的催化剂的甲苯转化率均随着载入量的增加而下降,而对二甲苯的选择性都有所提高。在浸渍法制备的La-ZSM-5沸石催化剂上,甲苯歧化生成对二甲苯的选择性可达80%。试验还指出,单独用磷改性的ZSM-5沸石催化剂的活性较低。再用稀土对PZSM-5催化剂改性,可使甲苯转化率从18%提高到30%。这是由于三价稀土元素可提供较多的质子酸中心。也是由于载入的磷和稀土元素对催化剂孔口和孔道尺寸有影响,从而改变了反应组份在分子筛中的扩散性质,提高了催化剂在生成对二甲苯时表现出的择形选择性。在一组用二种元素如磷-稀土、磷-镁和磷-镧改性的ZSM-5沸石催化剂中,评选出了对甲苯歧化反应具有较高活性和选择性的磷-镧改性催化剂,甲苯转化率为17%时,对二甲苯选择性可达90%左右。并且研究了反应条件对活性、选择性和反应产物的分布。在常压临氢条件下用该催化剂连续反应24小时,其活性稳定,转化率基本不变。     

ZnZrOx-HZSM-5双功能催化剂催化甲苯与合成气烷基化制对二甲苯

作为重要的有机化工原料,近些年来随着聚酯行业的高速发展,对二甲苯(PX)需求量逐年增高.目前,PX主要通过传统的石油路线生产,例如石脑油催化重整、甲苯歧化和C₈芳烃异构化,这些路线的后续精馏能耗较高.甲醇作为碳源与甲苯烷基化制备PX有效提高了目标产物的选择性,且已实现工业化.然而,由于甲醇生成甲氧基烷基化物种的能垒较高,使反应温度较高,促进了甲醇制烯烃(MTO)副反应的进行,降低了甲醇利用率;且由于积炭的形成,催化剂容易失活.合成气是非石油基资源如煤炭、天然气和生物质等利用的重要平台,在转化为醇类、烯烃以及芳烃路径中将经过甲氧基中间体,因此,本文研发以合成气代替甲醇与甲苯烷基化制备PX的催化剂和催化过程.基于本课题组关于CO₂加氢耦合甲苯烷基化制PX的研究基础,本文将ZnZrO_x(ZZO)与ZSM-5(Z5)混合制得双功能催化剂,用于合成气转化耦合甲苯烷基化制PX.研究结果表明,通过优化催化剂的组成和烷基化反应条件,调控CO加氢反应和甲苯烷基化反应的匹配性,在甲苯转化率为10.3%时,可获得64.8%的二甲苯选择性(不计水煤气变换反应),其中PX占81.8%,气态烃副产物的选择性为10.9%;在相同条件下采用甲醇为烷基化试剂时,二甲苯选择性仅38.5%,其中PX占38.8%,此时气态烃副产物的选择性达26.2%.同位素效应实验结果表明,二甲苯中新增甲基来自于合成气,而非甲苯的歧化反应.催化剂构效研究结果表明,PX的选择性与分子筛孔径、酸性强度以及Br?nsted酸性位点有关;原位红外结果也证实了该反应呈现逆同位素效应(k_H2/k_D2=0.92),表明反应中甲酸盐物种(HCOO*)加氢可能是反应的决速步骤.与传统的甲醇甲苯烷基化路径相比,采用来源广泛和成本较低的合成气与甲苯进行烷基化反应的温度(340℃)更低,有效避免了MTO副反应的发生,同时,该催化剂可在100 h内保持良好稳定性.综上,本工作结果为高效制备高值芳烃PX提供了新思路.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.