微量吸附量热研究CuO/γ-Al2O3催化剂的表面酸碱性质

The γ-Al₂O₃ supported CuO samples were studied. XRD results showed that the loading and calcination temperature affected the surface structure. For example， CuO crystallite appeared at the CuO loading of 7% (about 0.82mmol/100m²) on the support. Both CuO crystallite and CuAl₂O₄ spinel were present when the CuO/γ-Al₂O₃ sample was calcined at the same temperature (400℃). Microcalorimetric adsorption of CO₂ and NH₃ revealed that the strength of both the acidity and basicity decreased with the increase of CuO loading for the CuO/γ-Al₂O₃ sample. The increase of calcination temperature further decreased the basicity while the acidity was not affected.     

溶剂化金属原子浸渍法制备Pd-Cu/γ-Al2O3低温CO氧化催化剂

Nano-particle Pd/γ-Al₂O₃ monometallic and Pd-Cu/γ-Al₂O₃ bimetallic catalysts were prepared by solvated metal atom impregnation (SMAI) method. The results of XRD measurement indicated that Pd- Cu alloy was formed in the bimetallic catalysts and the crystalline particle size of the alloy increased as Cu contents increased with av-erage diameters < 6.0nm for all the samples. XPS and Auger spectra showed that Pd was in zero- valent state, Cu existed mainly in zero- valent state and partially in monovalent state Cu⁺. The Pd/γ-Al₂O₃ and Pd-Cu/γ-Al₂O₃ catalysts exhibited higher activity for CO oxidation at low temperature. The activity of Pd-Cu/γ-Al₂O₃ bimetallic catalyst was higher than that of Pd/γ-Al₂O₃ monometallic catalyst. The Pd-Cu/γ-Al₂O₃ catalyst with Pd/Cu atomic ratio of 1∶1 showed the highest activity.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

γ-Al2O3表面原位合成Ni-Al-CO3LDHs研究

Ni-Al-CO₃LDHs/γ-Al₂O₃have been prepared using an in-situ synthesis technique. NH₃·H₂O was chosen as activation agent of Al on the γ-Al₂O₃surface as well as precipitant. Ni-Al-CO₃LDHs/γ-Al₂O₃was synthesized by controlling the reaction conditions such as temperature, concentration of Ni²⁺ and initial pH. The crystalline structure, chemical composition and porous structure were characterized by means of XRD, FT-IR, TG-DTA, ²⁷Al MAS-NMR and N₂ adsorption-desorption. The resulting sample of Ni-Al-CO₃LDHs/γ-Al₂O₃possesses higher specific area and narrower pore distribution, in which Ni-Al-CO₃LDHs are located on the surface of γ-Al₂O₃and share the same Al-O bonds with the γ-Al₂O₃lattice. Finally a possible structural model was proposed to account for the porous characters of Ni-Al-CO₃LDHs/γ-Al₂O₃.     

Nd2O3添加量对BaTiO3陶瓷介电性能的影响

BaTiO₃ ceramics doped with Nd₂O₃(the additive content was respectively 0.001,0.002,0.003,0.005,0.01,0.03mol)were prepared by Sol-Gel method. Effects of Nd₂O₃ contents on the dielectric constant (ε), the dielectric loss (tanδ) ,the Curie-temperature (T_C) and the resistivity (ρ) of BaTiO₃ ceramic were studied. When Nd₂O₃ content was 0.001mol and 0.002mol, the dielectric constant was increased obviously, but the dielectric loss was also increased. When Nd₂O₃ content was 0.003mol, the dielectric constant was increased, and the dielectric loss was decreased, which was suitable for application in condenser. The resistivity was decreased obviously with the increasing of Nd₂O₃ contents, the resistivity was the smallest when Nd₂O₃ content was 0.001mol. The Curie-temperature was also decreased with the increasing of Nd₂O₃ contents.     

Ceramic Filter Balls Loaded with α-Fe2O3 and Their Application to NH3-N Wastewater Treatment

Hydrolysis reaction of Fe(NO₃)₃ at a high temperature in the presence of urea as the homogeneous precipitant was studied. With the prepared ceramic filter balls loaded with α-Fe₂O₃ after high temperature calcination, the loading of α-Fe₂O₃ on the porous ceramic filter balls from Fe(NO₃)₃ solutions of different concentrations and mechanical stability of the loaded α-Fe₂O₃ were studied. The product was characterized using XRD and SEM. Adsorption experiments were conducted to evaluate the performance of the product in adsorbing NH₃-N. It turned out that the specific surface area of the ceramic filter balls loaded with α-Fe₂O₃ had increased to 36.5387 m²/g from original 4.6127 m²/g. When the concentration of Fe(NO₃)₃ was 0.40 mol/L, the loading of α-Fe₂O₃ on the ceramic filter balls accounted for 8.4% of the total mass of the adsorbent and α-Fe₂O₃ was adsorbed on the filter balls very well. The adsorption isotherm of NH₃-N on the ceramic filter ball adsorbent loaded with α-Fe₂O₃ was of Langmuir type. The saturated adsorption capacity was 3.33 mg/L, and the adsorption constant K was 0.1873. NH₃-N was adsorbed by α-Fe₂O₃ more easily, which was a kind of specific adsorption.     

Cu-Ni/La2O3热解C2H2制备碳纳米管的研究

Nano-sized and well-dispersed Cu-Ni/La₂O₃ can be obtained by reduction of LaCu_0.2Ni_0.8O₃ with the structure of perovskite. Using Cu-Ni/La₂O₃ as catalyst and C₂H₂ as carbon source, carbon nanotubes with a high yield and narrow diameter distribution can be obtained in the reaction temperature range of 650～700℃. Outer diameter of carbon nanotubes rangs from 9nm to 14nm. TG, Raman and XPS analysis indicate that carbon nanotubes prepared by Cu-Ni/La₂O₃ are relatively higher in graphitic degree.     

ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

准球形α-Fe2O3的形成过程研究

The formation process of pseudo-spherical α-Fe₂O₃ particles obtained through the hydrolysis of 0.01 mol·L^-1 FeCl₃ solution was studied by means of TEM and XRD. The results show that the growth of α-Fe₂O₃ nuclies is through the diffusion mechanism. Although the presence of CTAB in the FeCl₃ solution has no effect on the growth process of pseudo-spheric α-Fe₂O₃ particles, more uniform particles are obtained, and the particles are self-assembled to form two-dimensional ordered structure due to the effect of CTAB. The optical character of these α-Fe₂O₃ particles was investigated, and the band-gap of which is about 2.49 eV.     

碳纳米管负载的Fe2O3催化剂制备

Carbon nanotubes were modified by FeSO₄-H₂O₂ system, iron hydroxides were adsorbed on the wall of carbon nanotubes simultaneously. These precursors were treated at 723K for 2 h under hydrogen, nitrogen and air atmosphere to prepare carbon nanotubes supported γ-Fe₂O₃catalyst, γ-Fe₂O₃and α-Fe₂O₃compound catalyst and amorphous Fe₂O₃catalyst, respectively. This is green method to prepare high Fe₂O₃loading (≥50 %) catalyst without adding other cation. The different structures Fe₂O₃catalysts can be synthesized by controlling the condition of thermal treatment to content active phase requirements for different catalytic reactions. The paper presents a new method to prepare carbon nanotubes supported catalysts.     

不同稀土改性SO42-/ZrO2催化剂的结构与性能表征

Solid superacid catalyst SO₄^2-/ZrO₂ was modified by different rare earth compounds and applied to the esterification of acetic acid and n-butanol. The effects of rare earth elements loading on the catalytic properties were studied and the correlation between the structure and properties was investigated by means of XRD, IR, UV, DTA and TG. The results show that the (NH₄)₂Ce(NO₃)₆ modification can enhance catalytic activity more and exhibit better stability than the other two compounds La(NO₃)₃ and Ce(NO₃)₃. Meanwhile,(NH₄)₂Ce(NO₃)₆ modification can restrain the loss of SO₄^2- efficiently. The optimum calcination temperature and molar ratio of Ce(NH)∶Zr for SO₄^2-/ZrO₂ catalyst modified by (NH₄)₂Ce(NO₃)₆ are 450 ℃ and 2, respectively.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

草酸盐共沉淀法制备Y1.84La0.16O3纳米粉体

Nanopowder of Y_1.84La_0.16O₃ was prepared by oxalate co-precipitation method. The powder was characterized by TG-DTA, XRD and TEM. The results show that the precursor is Re₂(NO₃)₂(C₂O₄)₂·2H₂O (Re=Y, La), and the Y_1.84La_0.16O₃ nanopowders produced by calcining the precursor at 1 000 ℃ for 4 h are 20～40 nm spherical particles and well dispersed. The powders were with high sintering activity and could be fabricated to transparent ceramic without additive at 1 450～1 550 ℃ in H₂ atmosphere for 3 hours. The total transmission of the transparent ceramic could reach 80%.     

球形Gd2O3∶Eu纳米发光材料的制备

Spherical nanometer Gd₂O₃∶Eu luminescent materials were prepared by homogeneous precipitation method, and the properties were studied also. TG, FTIR and XRD analysis showed that the precursor was carbonate, the cubic Gd₂O₃was obtained after calcination. TEM photographs indicated that the samples were spherical and well dispersed with nanometer and submicrometer size of 200～300 nm which is the nanoparticles’ aggregate. The mechanics of agglomerating growth is also discussed. ED photograph showed that the particle was crystalline. The PL analysis exhibited that CTB band of nanometer Gd₂O₃∶Eu was of 17 nm red shift to bulk materials, and the emission peak was broadened due to the surface and interface effect of nanocrystals.     

掺钇锆酸锶-TiO2复合光催化剂的制备及性能研究

SrZrO₃ particles were prepared by a co-precipitation method and Sr(Zr_1-xY_x)O_3-δ -TiO₂ composite particles were then synthesized by Sr(Zr_1-xY_x)O_3-δ and titanium dioxide. The composite particles were characterized by XRD, SEM, FTIR and TG-DTA techniques. The photocatalytic degradation of methylene blue (MB) in aqueous solution was used as a probe reaction to evaluate the photocatalytic activity of the composite particles. The effect of the preparation method for SrZrO₃, doping content of yttrium and TiO₂ amount in the composite particles on the photocatalytic activity of composite particles was also discussed. The results show that the methylene blue solution could be completely degraded by Sr(Zr_1-xY_x)O_3-δ -TiO₂ composite particles under UV-light or visible light irradiation. The photocatalytic activity of composite particles was higher than that of pure TiO₂. The fast recombination of photogenerated electrons and holes were restrained by the heterojunction formed in composite particles. The particle of SrZrO₃ prepared by co-precipitation was small, and the photocatalytic activity of composite particles prepared from this kind of SrZrO₃ was higher than that of particles prepared by solid sintering method. The best doping content of yttrium is 5%. The optimal content of TiO₂ in composite particles is 90wt%, 70wt%, respectively under UV-light and visible light irradiation, the degradation rates of MB are 98.8% and 93.5% , respectively after 50 min irradiation.     

MgFe2O4-Fe2O3纳米粉体的软化学合成及电磁学特性

Nano-MgFe₂O₄-Fe₂O₃ magnetic powders were synthesized by citrate gel under microwave irradiation. The structure，particle size distribution，electromagnetic characteristics of nano-MgFe₂O₄-Fe₂O₃ were characterized by using TG-DTA, X-ray, electronic microscope, nano-size measurement and electromagnetism measurement apparatus。The results show that the product is a mixture of MgFe₂O₄ and Fe₂O₃ with average size of 44 nm, tanδ for the product is 0.265 and 0.610 at frequency of 1.0 GHz and 1.8 GHz respectively.     

无氨湿法制备纳米晶In2O3及表征

Preparation of In₂O₃nano-scale powders by ultrasonic and homogeneous precipitation, using metal In and urea as raw materials, was reported for the first time, while the effects of reaction temperature, the ratio of the materials and the pH etc. on the preparation was dicussed. This method can be operated and industrialized easily with very low cost． The structural properties of precursor and In₂O₃were characterized by TG-DTA, XRD, ESCA and TEM. The results show that In₂O₃produced are very pure, monophase and spherical nano-scale powders with average size of 25 nm.     

TiO2胶粒在铝合金表面的电泳沉积及所制薄膜的光催化性能研究

TiO₂ membranes were prepared on aluminum-alloy thin plates by electrophoretic deposition and dip coating in a colloid solution of TiO₂, respectively. The photocatalytic activity of TiO₂ membrane was compared using ethylene as reactant, and the crystal and morphological structure of the membrane were characterized by XRD and SEM. The results showed that a more compact membrane with high loading of TiO₂ but lower photocatalytic activity of unit TiO₂ mass was obtained by electrophoresis compared with dip coating method. The addition of polyethylene glycol (PEG) to the sol of TiO₂ could improve the specific photocatalytic activity (ethylene conversion per unit mass TiO₂ and unit area of membrane piece) of the electrophoresis-membrane prepared from the sol, but could not change the specific photocatalytic activity of the dip-coating membrane from the sol. The ethylene conversion on the electrophoresis membrane prepared from the sol containing PEG (50 g·L^-1) was 9 times of that on the dip coating membrane. The effect of PEG on the properties of electrophoresis-membrane of TiO₂ was attributed to the change of electrokinetic properties of sol. Addition of PEG decreased ζ potential value of the sol and the mobility of the sol particle, increased viscidity of the colloid, thus decreasing both the electrophoresis deposition velocity of colloid particles and the electroosmosis velocity of diffuse layer of colloid particles. These favored the formation of a low compact and porous membrane on the electrode in electric field, and thus increasing the availability of TiO₂ in photocatalytic process.     

由镁、铝醇盐配合物合成纳米粒子MgAl2O4尖晶石

Mg and Al alkoxide complex was synthesized in a cell without battery separator by electrochemical dissolution of aluminum for 6 h and magnesium for 1.8 h at 45 ℃ in ethanol solution of 0.04 mol·dm^-3 (Bu₄N)Br with a current density of 100 mA·cm^-2. IR and Raman spectroscopy were used to characterize the structure of the precursor of MgAl₂O₄. The results show that the current efficiency attains 98.4% and the precursor is MgAl₂(OCH₂CH₃)₅(acac)₃. The acac^- group-containing precursor could prevent it from agglomeration. The xerogel was obtained by drying in vacuum for 24 h and hydrolysis under pH≈8.5 of the precursor, which was heated at 350 ℃ for 2 h to obtain the nano-MgAl₂O₄ powder. XRD and TEM were used to investigate the structure of nano-MgAl₂O₄. The result suggests that the xerogel with an average particle size of 10 nm and the Nano-sized Spinel MgAl₂O₄ Particle of 12 nm thus obtained are with high purity.