聚四氟乙烯和氟化乙丙烯共聚物复合膜的压电性

以多孔PTFE膜为骨架,而以致密（非多孔）FEP膜为储电介质层的孔洞结构复合压电驻极体膜的制备方法.利用正压电效应,测量了复合膜的准静态压电系数d₃₃;研究了压电系数的热稳定性和复合膜中空间电荷的动态特性;并通过介电谐振谱的分析,比较了这类复合膜的准静态和动态压电系数.结果表明：FEP和PTFE复合膜压电驻极体的准静态压电系数d₃₃可以达到300 pC/N.经90℃老化20 h 后的d₃₃仍保持在初 关键词： 压电驻极体 压电性 多孔聚四氟乙烯 致密氟化乙丙烯共聚物     

氟聚合物压电驻极体的压电性及其电荷的动态行为

描述了一种可控微结构的多孔聚合物压电功能膜的制备方法,讨论了采用该工艺制备的聚四氟乙烯(PTFE)和全氟乙丙烯共聚物(FEP)复合膜压电驻极体的压电性能及其热稳定性.通过等温压电系数衰减和短路热刺激放电(TSD)方法,研究了氟聚合物复合膜压电活性热稳定性改善的根源,以及脱阱电荷输运和复合的特性.结果表明,这类氟聚合物压电驻极体膜的准静态压电系数d₃₃可高达2200pC/N;压电系数d₃₃的压强特性在直到20kPa的压强范围内呈现良好的 关键词： 氟聚合物 压电驻极体 热稳定性 电荷动态特性     

人工调控微结构压电驻极体的热稳定性和电荷动态特性

利用表面带有周期性结构的硬质模板,通过冷压工艺将周期结构图案复制到多孔聚四氟乙烯(PTFE)薄膜表面,再经过热黏合工艺与致密氟化乙丙烯共聚物(FEP)薄膜复合,制备出了高度有序的微孔结构复合膜,并用电晕充电的方法对复合膜进行极化处理,最终获得氟聚合物复合膜压电驻极体.借助对这类复合膜压电驻极体介电谐振谱的测量,得到了材料的杨氏模量.并利用等温热老化工艺对它们的压电系数d33的热稳定性进行了考察.最后通过短路热刺激放电谱的测量和分析,讨论了该复合膜在热老化处理后的电荷动态 关键词： 有序结构 压电驻极体 压电性 电荷动态特性     

聚丙烯压电驻极体膜的压电和声学性能研究

以多孔聚丙烯(PP)膜为原材料, 通过压缩气体膨化工艺和电晕极化方法成功制备出PP压电驻极体膜, 并研究了该功能膜的压电和声学性能. 结果表明PP压电驻极体膜厚度方向和横向的杨氏模量分别为1.4和480 MPa, 因此压电系数d₃₃比d₃₁和d₃₂高2个量级以上, d₃₃是该类压电膜压电效应的主要性能指标, 而 d₃₁和d₃₂可以忽略不计. PP压电驻极体膜的准静态压电系数d₃₃在15-35 kPa的压强范围内具有良好的线性度. 在2-300 Hz的测试频率范围内, 300 Hz 下的d₃₃是2 Hz下的81%, 这主要是由PP膜的杨氏模量随频率增大而增强引起的. 在100 Hz-100 kHz 的音频和超声波频率范围内, PP压电驻极体膜具有平坦的频响曲线; 在1 kHz下其开路电压灵敏度和压电系数d₃₃分别为0.85 mV/Pa和164 pC/N. 关键词： 聚丙烯压电驻极体 压电效应 声学性能     

多基元聚焦空气耦合超声换能器*

文中针对空气耦合超声换能器及其在表面缺陷检测中的应用开展了研究。选用1-3型压电复合材料及双匹配层结构来实现超声换能器压电材料与空气之间声阻抗的逐渐过渡,提高压电材料/空气界面的声能量透射率进而提高空气耦合超声换能器的灵敏度。在此基础上研发制作了440 kHz多基元聚焦空气耦合超声换能器,并对其性能进行了测试。其焦距、焦宽及焦深分别为41.44 mm、1.14 mm和20.30 mm,灵敏度和带宽分别为-50 d B和20.2%。测试结果表明该空气耦合超声换能器具有优良的性能,利用该超声换能器可以有效检测材料表面缺陷。     

聚四氟乙烯多孔膜的压电活性及其稳定性

研究了经单向机械拉伸形成的非极性空间电荷型薄膜驻极体聚四氟乙烯(PTFE)多孔膜的压电性.讨论了由PTFE多孔膜和非多孔的聚合物薄膜（PTFE，聚酰亚胺PI，氟化乙丙烯共聚物FEP 和聚三氟氯乙烯PCTFE）组成的双层膜的突出压电活性.初步研究结果指出：在优化的极化条 件下形成的上述双层压电膜以外电极测量的准静态压电d₃₃常数可达186 pC/N， 这个数值与压电陶瓷锆钛酸铅PZT的相应常数接近，而比铁电聚合物聚偏氟乙烯(PVDF)的相 应常数约高出一个数量级.还研究了这类柔性多孔膜 关键词： 聚四氟乙烯多孔膜 压电性 空间电荷驻极体 充电参数 压电活性的热稳定性     

一种压电超声波物料输送器*

利用压电陶瓷元件具有良好声电转换特性和输出特性,本文提出了一种新型结构的压电超声波物料输送器。设计了超声波物料输送器的结构并分析了其工作原理,采用纵扭复合型压电换能器为驱动源,对压电换能器进行了结构设计和参数计算,并对其进行了性能测试。由此研制出了压电超声波输送器的样机并进行了试验测试,结果表明:当频率为17.9 kHz–18.6 kHz时,输送器具有输送物料能力。驱动负载为1.5 kg时系统的谐振频率为18.3 kHz,输送速度最快,达到64个/min。随着电源输出功率的增大输送物料速度呈线性增加。该输送器的稳定性好,噪声低。与压电片式和电磁式输送器噪声进行对比,超声波输送器的工作噪声仅为31 dB,略小于压电片式,远小于电磁式。     

由辐射膜同空气耦合的200kHz超声换能器

Matjaz Babic报道了一种新型的空气中发射用200kHz超声换能器。为改善声源与空气之间声阻抗的严重失配问题,通常采用的方法是:对高频超声(如200kHz以上的超声),多应用声阻抗匹配技术;对较低频的超声(如50kHz以下),多应用弯曲振动换能器,例如将压电品片与金属膜片粘在一起,使其产生复合弯曲振动。     

水下声成像PVDF—DMOS换能器

本文通过研制水下声成像PVDF-DMOS集成接收换能器,分析了高分子压电薄膜在水声中应用的新途径及其组成换能器的振动模式,建立了机电等效电路图.并分析了影响器件灵敏度的诸因素.介绍了本工作的测量结果,评价了器件的特性.本文可供设计各种PPDF压电换能器、传感器时参考.     

声光器件的换能器带宽和镀层厚度的确定

根据压电换能器的Mason等效电路,就36°у切LN/PM声光器件和x切LN/TeO₂声光器件以及各种镀层材料和厚度计算了换能器损耗TL随规一化频率f/f₀的变化关系,由此可确定各镀层的厚度和器件的换能器带宽,还给出器件的电输入阻抗z_i在阻抗圆图上随f/f₀变化的轨迹,它可作为器件性能测试的理论依据。 关键词：     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.