1150 nm High-Power Fiber Laser Oscillator Pumped by 976 nm Laser Diode

We present an all-fiber 1150 nm Yb-doped fiber laser oscillator pumped by a 976 nm laser diode. To suppress amplified spontaneous emission and avoid parasitic laser oscillation, we propose a long-length gain fiber and a high-reflectivity output fiber Bragg grating in the fiber laser oscillator. The 1150 nm band single-mode fiber laser with output power of 20.5 W is demonstrated at room temperature. The optical-to-optical conversion efficiency ranges up to 51.6% at the maximum output. The central wavelength of the fiber laser oscillator is 1150.35 nm, and its 3 dB spectral width is 0.72 nm. No evidence of amplified spontaneous emission, residual pump light, or parasitic laser oscillation were observed in the experiments. The high-power 1150 nm fiber laser oscillator can be used as a pump source in the development of a 3 μm Ho-doped fiber laser.     

Simultaneous Double-Color Continuous Wave Raman Fiber Laser at 1239 nm and 1484 nm Using Phosphosilicate Fiber

Simultaneous double-color high-power continuous wave (CW) Raman fiber laser at 1239 nm and 1484 nm is demonstrated which uses CW 8.4 W Yb-doped double-clad fiber laser at 1064 nm as a pump, 1 km phosphosilicate fiber, and cascaded cavities consisting of two pairs of fiber Bragg grating (FBG) mirrors. Maximum output powers are 0.65 W at 1239 nm and 0.97 W at 1484 nm with a 50%/50% output mirror reflectivity pair, and 0.37 W at 1239 nm and 1.06 W at 1484 nm with a 75.5%/50% pair. The output characteristics of this laser for different FBG mirror reflectivities are reported.     

A High Efficiency Yb3+-doped Fiber Ring Cavity Laser with Narrow Line-width

A novel Yb3+-doped fiber ring cavity laser pumped by a 977 nm laser diode is presented with its output laser wavelength of 1060 nm. Based on a fiber Bragg grating (FBG), the laser exhibits 0.20 nm line-width, 7.5 mW laser output power, 40 dB signal-to-noise ratio (SNR) and 66% slope efficiency.     

Optimization of linear cavity design of Yb-doped double-clad fiber laser

The output characteristics of a linear cavity Yb-doped double-clad fiber (DCF) laser, including the effects of fiber length, fiber loss, and output mirror reflectivity on laser output power and threshold pump power have been studied theoretically and experimentally. In this paper, the linear cavity of double-clad fiber laser (DCFL) was composed of a pair of fiber Bragg gratings, while the facet of fiber was anti-reflection (AR) coated at 1070nm to erase the Fresnel reflection. Analysis showed that the laser output increases as the reflectivity of the fiber Bragg grating used as the output mirror decreases. At last, under the pump power of 14.4 W, single-mode laser output at 1070 nm was up to 10.8 W, with slope efficiency of 75 %.     

All-fiber clad-pumped Tm3+-doped fiber amplifier using high power fiber combiner

The diode laser (LD) clad-pumped 1947.6 nm continuous wave (CW) Tm³⁺-doped fiber amplifier is reported using the master oscillation power amplifier (MOPA) method. The injected seed laser is provided by an all-fiber LD-clad-pumped Tm³⁺-doped single-mode fiber laser, which has a nearly 2.4 W maximal output power and 0.1 nm ultra-narrow linewidth based on the intracore reflection FBG. Using the 25/400 μm double-clad LMA Tm³⁺-doped fiber as the gain fiber, the output maximal output power is 30.6 W from the fiber amplifier, with a slope efficiency of 39.1% respected to the LD total output power. A high power multi-mode fiber combiner is used to couple high power LD light into the gain fiber. The output wavelength is also located at 1947.6 nm, with the slightly expanded laser linewidth of 0.2 nm.     

1137 nm长波掺镱光纤激光器的出光实验

分别使用976 nm半导体激光器和1040 nm光纤激光器作为泵浦源,实现了1137 nm长波光纤激光器的出光,输出功率均超过百mW。激光器采用相同的线性腔结构,高反光栅和低反光栅的反射率分别为99.6%和39.7%,增益介质是一段8 m长的掺镱光纤,纤芯直径5 m。当976 nm半导体泵浦功率为912 mW时,1137 nm激光输出功率为182 mW,对应的斜率效率为28.5%;当1040 nm激光功率为1.59 W时,输出的1137 nm激光功率为278 mW,斜率效率约为25%。在此基础上对两种泵浦方式进行了对比分析。     

Output Characteristics of High-Power Continuous Wave Raman Fiber Laser at 1239 nm Using Phosphosilicate Fiber

A high-power singlemode Raman fiber laser (RFL) with maximum output power of 4.11 W and maximum power conversion efficiency of 47.40% at 1239 nm is realized using continuous wave 8.4 W Yb-doped double-clad fiber laser as a pump, 700 m phosphosilicate fiber, and a Raman cavity formed by a pair of fiber Bragg grating mirrors at 1239 nm. The output characteristics of the RFL at 1239 nm for different fiber lengths and output mirror reflectance are reported. Theoretical simulation is done to numerically optimize for fiber length and output coupler reflectivity to obtain maximum first Stokes power.     

掺钕保偏光纤激光器的研究

对掺钕光纤激光器输出功率沿光纤的分布以及不同光纤长度下抽运功率和输出功率沿光纤的分布进行了数值模拟.以808nm半导体激光器为抽运源，掺钕双包层保偏光纤为增益介质，对保偏光纤激光器进行了探索性的实验研究.分别就光纤不同弯曲形状和弯曲半径对激光器输出功率指标和偏振特性的影响进行了研究，实验中发现在1060nm和1092nm处有两个峰值.在波长1060nm处得到了7.35W的连续偏振激光输出，斜率效率为58.3％. 关键词： 激光技术 光纤激光器 掺钕保偏光纤 偏振     

15波长输出的布里渊掺铒光纤激光器

多波长布里渊掺铒光纤激光器是一种新型的多波长光纤激光器,其原理是利用受激布里渊增益和掺铒光纤的线性增益,可以在常温下得到波长间隔约为0．08nm(～10GHz)的多波长输出。报道的布里渊掺铒光纤激光器,在布里渊抽运功率为1．7mW、980nm抽运功率为300mW的情况下得到稳定的15个波长(间隔～10GHz)的输出,这种激光器用作光传感器、光谱分析仪以及密集波分复用系统的光源。实验发现,输出波长的个数随着980nm抽运功率的增大而增加。另外,布里渊掺铒光纤激光器的信号功率主要来自于掺铒光纤的增益,而布里渊增益对它的影响不大。     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

 利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb³⁺)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

间隔可调多波长光纤激光器的实验研究

半导体光放大器(SOA)的非均匀加宽特性对产生多波长激光非常有利。本文对两段式立奥-萨尼亚克(Lyot-Sagnac)滤波器进行了详细的理论分析,实现了一种基于半导体光放大器的新型多波长光纤激光器。它利用立奥-萨尼亚克滤波器的波长选择性,在室温下得到了约18个具有30 dB信噪比的多波长激光输出。波长范围1556~1577 nm。通过调节立奥-萨尼亚克环内的偏振控制器,多波长激光的波长间隔可在两种国际电信联盟(ITU)标准波长间隔(0.4 nm和0.8 nm)间选择。这种构型的光纤激光器具有稳定性好、波长间隔可控、信噪比高等优点。     

内腔级联拉曼光纤激光器输出特性的实验研究

采用标准单模石英光纤作为拉曼增益介质，光纤布拉格光栅作为谐振腔镜，研制了一台内腔级联拉曼光纤激光器。利用掺Yb双包层光纤激光器作为抽运源，实现了二级拉曼转换，在波长1176.8nm获得了309mW的最大输出功率，斜率效率接近51.5％。在小抽运功率下，发现拉曼光纤激光器的输出中存在重复周期约为2.9μs的脉冲序列；当抽运功率大于某一值时，上述脉冲消失，获得了十分稳定的连续输出。     

高功率半导体激光泵浦源研究进展

高功率半导体激光器是固体激光器和光纤激光器的主要泵浦源。激光泵浦源性能的大幅提升直接促进了固体激光器、光纤激光器等激光器的发展。主要介绍了8xx nm和9xx nm系列半导体激光泵浦源的最新研究进展,8xx nm单管输出功率已达18.8 W@95μm,巴条输出功率已达1.8 kW(QCW),9xx nm单管输出功率已达35 W@100μm,巴条输出功率已达1.98 kW(QCW)。谱宽<1 nm的窄谱宽半导体激光器输出功率可达14 W。展望了未来半导体激光器泵浦源的发展趋势。     

Tunable fiber Bragg gratings for application in tunable fiber lasers

The resonance wavelength of the fiber Bragg gratings (FBGs) is tuned using two methods. Tunable FBGs are used as the selecting elements in the cavities of tunable lasers. An ytterbium-doped fiber laser with a wavelength tuning range of 1063–1108 nm and an output power of 6 W, a Raman fiber laser with a wavelength tuning range of 1252–1303 nm and an output power of 3 W, and an erbium-doped fiber laser with a wavelength tuning range of 1530–1580 nm are realized, and their characteristics are studied.     

High-power Tm-doped fiber distributed-feedback laser at 1943 nm

We report on high-power operation of a fiber distributed-feedback (DFB) laser fabricated from Tm-doped photosensitive alumino-silicate fiber and in-band pumped by an Er/Yb fiber laser at 1565 nm. The fiber DFB laser yielded up to 875 mW of single-ended output at 1943 nm on two orthogonally polarized modes for 3.5 W of absorbed pump power. Further scaling of the DFB laser output power was achieved with the aid of a simple Tm-doped fiber amplifier stage spliced directly to the DFB fiber without the need of an optical isolator. The maximum output power from the DFB laser and fiber amplifier was >3 W for a combined absorbed pump power of 8.1 W. The influence of thermal loading, owing to quantum defect heating in the Tm-doped core, on the output power and longitudinal mode behavior is discussed, and the prospects for further improvement in performance are considered.     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

5 kW全光纤结构1018 nm激光合成

光纤激光同带抽运方案具有泵浦亮度高、量子亏损小等优势,有着巨大的功率提升潜力,是近年来国际上的研究热点。1018 nm光纤激光可作为高功率掺镱光纤激光器的高效同带抽运源,但是单个1018 nm光纤激光器输出功率有限,光束合成是突破这一局限的重要方案。基于19台单模1018 nm光纤激光器和一个191光纤功率合束器,搭建了一套全光纤结构激光合成系统,实现了5 kW的1018 nm合成激光输出。     

高功率、低量子亏损同带抽运掺镱光纤放大器

开展了基于同带抽运的高功率、低量子亏损的掺镱光纤放大器实验研究. 搭建了一台输出功率为21 W的1018 nm短波 长掺镱光纤激光器, 并利用其对双包层掺镱光纤进行同带抽运, 获得18.6 W的1080 nm波段激光输出, 光-光转换效率高达90.86%. 关键词： 光纤放大器 同带抽运 双包层光纤 转换效率     

Output power improvement in an Yb-doped fiber laser with an additional unpumped Yb-doped fiber

Master oscillator power amplifier (MOPA) technology has been widely used in high-power or ultrashort-pulse fiber laser systems because the shape of the laser pulse can be easily adjusted. Usually, the first amplification stage of a 1064 nm fiber laser uses the core-pumped Yb-doped fiber amplifier (YDFA); however, the gain or output power is limited owing to the strong amplifier spontaneous emission (ASE) in the 1030 nm band. This paper presents the improved output power in an YDFA by inserting an additional unpumped Yb-doped fiber, which absorbs the lost backward ASE emitted from the pump end. We achieved an output power increase of more than 10% in a low-power signal, and the increase in output power decreased as the signal power increased. Moreover, the insertion of an additional unpumped Yb-doped fiber restricted the unwanted 1030 nm lasing in a low-power signal.     

高能掺镱离子光纤激光器的研究

从激光器的速率方程出发,对光纤激光器的工作原理以及输出特性进行了研究,得到了光纤激光器在稳态条件下阈值条件和激光器输出功率的表达式.利用数值模拟结果对光纤激光器基本参量进行分析和论证.为光纤激光器的优化设计提供理论依据.并提出了全光纤型光纤激光器的实验方法.获得了最大功率7.5 W、波长1080 nm、峰值半宽0.11 nm的连续单模激光输出.