Mn4+掺杂对BiFeO3陶瓷微观结构和电学性能的影响研究

利用传统的固相反应法制备了BiFe_1-xMn_xO₃ (x= 0-0.20)陶瓷样品, 研究了不同Mn⁴⁺掺杂量对BiFeO₃陶瓷密度、物相结构、显微形貌、 介电性能和铁电性能的影响.实验结果表明:所制备的BiFe_1-xMn_xO₃ 陶瓷样品的钙钛矿主相均已形成,具有良好的晶体结构, 且在掺杂量x=0.05附近开始出现结构相变.随着Mn⁴⁺添加量的增加, 体系的相结构有从菱方钙钛矿向斜方转变的趋势,且样品电容率大幅度增大, 而介电损耗也略有增加;在测试频率为10⁴ Hz条件下, BiFe_0.85Mn_0.15O₃ (ε_r=1065)的 ε_r是纯BiFeO₃ (ε_r=50.6)的22倍; 掺杂后样品的铁电极化性能均有不同程度的提高,可能是由于Mn⁴⁺稳定性优于 Fe³⁺,高价位Mn⁴⁺进行B位替代改性BiFeO₃陶瓷, 能减少Bi³⁺挥发,抑制Fe³⁺价态波动,从而降低氧空位浓度,减小样品的电导和漏电流.     

三明治结构Tan(B3N3H6)n+1 团簇的磁性和量子输运性质

利用密度泛函理论和非平衡格林函数方法, 本文对小尺寸团簇Ta_n(B₃N₃H₆)_n+1 (n ≤ 4)的磁性和量子输运性质进行了系统的研究. 计算结果表明, 此类体系采用三明治结构作为其基态并且具有较高的稳定性. 体系的磁矩随团簇尺寸的增大而线性增大. 当把Ta_n(B₃N₃H₆)_n+1团簇耦合到Au电极上时, 形成的Au-Ta_n(B₃N₃H₆)_n+1-Au体系在有限偏压下展示出了较强的自旋过滤能力, 因而可以被看做是一类新型的低维自旋过滤器.     

Si1-xGex合金半导体中CiCs和CiOi缺陷随Ge含量的变化

采用从头计算(ab initio)的方法对Si和Si_1-xGe_x合金半导体材料中C_iC_s缺陷的性质进行探讨，同时也对比调查了C_iO_i缺陷在Si和Si_1-xGe_x合金中的性质. 在不同Ge含量的Si_1-xGe_{x相似文献}   

TeOx薄膜结构及短波长静态记录特性的研究

以真空蒸镀法在K9玻璃基底上制备了TeO_x单层薄膜.使用X射线光电子能谱仪(XPS)、X射线衍射仪(XRD)、原子力显微镜(AFM)对薄膜的结构进行了分析.实验结果表明,薄膜是由晶态Te分散在非晶态TeO₂基体中形成的混合体系,TeO₂基体的存在增强了Te的抗氧化性能;薄膜具有精细粒状结构和粗糙的表面;退火后薄膜的反射率增加和Te向表面的偏析、重聚集及表面粗糙度的降低有关.采用波长为514.4nm的短波长静态记录仪对薄膜静态记录性能的测试结果表明:薄膜具有良好的记录灵敏性,在记录功率1.5mW、脉宽50ns时就可产生较高的反射率衬比(度).研究结果为选择合适掺和物使TeO_x薄膜实际用作高密度光存储介质有重要意义.     

共轭低聚物中光生分子间电荷转移态的第一性原理研究

本文基于第一性原理中的Heyd-Scuseria-Ernzerh方法研究了单层In_1-xGa_xN的电子结构和光学性质.计算得到单层In_1-xGa_xN的能带结构和态密度（DOS）,发现随着掺杂比例的变化,体系带隙的变化范围是1.8~3.8 eV,表明通过Ga的掺杂可以实现体系带隙值的调节.并且还研究了单层In_1-xGa_xN的介电函数,折射率和吸收系数等光学性质,结果表明随着Ga掺杂浓度的增加,介电函数谱的主峰和吸收谱发生了显著的蓝移.此外,基于能带结构和态密度图谱,对单层In_1-xGa_xN的光学性质进行分析,预测这种材料独特的光学性质在纳米电子学和光学器件中会有广泛的应用.     

通过掺杂V和F提高碳包覆的磷酸铁锂锂离子电池的电化学性能

在原位聚合合成方法的基础上,结合两步烧结过程制得LiFe_1-xV_x(PO₄)_(3-y)/₃F_y/C.V和F掺杂对碳包覆的磷酸铁锂材料的结构、形貌和电化学性能有影响.通过XRD、FTIR、SEM、充/放电测试和电化学阻抗谱对材料的结构、形貌和电化学性能进行了表征.结果表明,V和F的掺杂并没有破坏橄榄石结构中的LiFePO₄/C,但可以提高晶体结构的稳定,降低电荷的转移阻抗,提高锂离子扩散速度,改善了LiFePO₄/C材料的循环性能和高倍率性能.     

Nd掺杂对Bi4Ti3O12铁电薄膜的微结构和铁电性能的影响

利用溶胶-凝胶法在Pt/Ti/SiO₂/Si(100)衬底上制备了Nd掺杂Bi₄Ti₃O₁₂(Bi_4-xNd_xTi₃O₁₂, x=0.00,0.30,0.45,0.75,0.85,1.00,1.50)铁电薄膜样品.研究了Nd掺杂对Bi₄Ti₃O₁₂薄膜的微结构和铁电性能的影响.研究结果表明:Nd掺杂未改变Bi₄Ti₃O₁₂薄膜的基本晶体结构.在掺杂量x<0.45时,Nd³⁺只取代类钙钛矿层中的A位Bi³⁺.当x=0.45时,样品剩余极化强度达最大值,在270kV·cm^-1的电场下为32.7μC·cm^-2.掺杂量进一步增加时,结构无序度开始明显增大,Nd³⁺开始进入(Bi₂O₂)²⁺层,削弱其绝缘层和空间电荷库的作用,导致材料剩余极化逐渐下降.当掺杂量x达到1.50时,掺杂离子最终破坏(Bi₂O₂)²⁺层的结构,材料发生铁电-顺电相变.     

ECR-PECVD制备Si3N4薄膜的光学特性研究

本文研究了ECR-PECVD制备的Si₃N₄薄膜的光学特性.得到的Si₃N₄薄膜具有光致发光效应,在280℃沉积制备的Si₃N₄薄膜的光致发光波长为400nm,具有较好的单色性.测试分析了Si₃N₄薄膜对可见光、红外光具有较高的透射性能,Si₃N₄薄膜可作为红外光的增速减反射膜.     

离子注入掺杂锐钛矿TiO2薄膜的光学性能

 在玻璃基体上,采用射频磁控溅射方法在不同的基体温度下制备了TiO₂薄膜,然后在薄膜中注入注量分别为5×1016, 1×1017和5×1017/cm2的N离子以制备N掺杂的TiO₂薄膜。X射线衍射结果表明：制备出的TiO₂薄膜为锐钛矿型。X射线光电子能谱研究结果表明：注入的N离子与TiO₂晶粒相互作用,形成了含氮的TiO_xN_2-x化合物,从而改变了TiO₂薄膜的吸收边;随N离子注量增加,吸收边移动更明显;同时,由于氮离子注入产生的辐照缺陷使TiO₂薄膜在紫外和可见光区的吸收也明显增强。     

纤锌矿BeO掺Cd的电子结构与能带特性研究

采用基于密度泛函理论平面波赝势方法, 对纤锌矿BeO掺Cd的Be_1-xCd_xO合金进行电子结构与能带特性研究. 结果表明: Be_1-xCd_xO的价带顶始终由O 2p电子态决定, 而导带底由Be 2s和Cd 5s的电子态决定.随着Be_1-xCd_xO合金的Cd掺杂量增加, Cd 4d与O 2p的排斥效应逐渐加强, 同时Be_1-xCd_xO的带隙逐渐变小, 出现"直接-间接-直接"的带隙转变. 为了使理论值与实验值相一致, 对Be_1-xCd_xO带隙进行修正, 并分析了纤锌矿BeO-ZnO-CdO三元合金的带隙和弯曲系数与晶格常数的关系.     

MnxSi1-x磁性薄膜的结构研究

利用X射线衍射(XRD)和X射线吸收近边结构(XANES)方法研究了在Si(100)衬底上及600℃温度条件下用分子束外延(MBE)共蒸发方法生长的Mn_xSi_1-x磁性薄膜的结构.由XRD结果表明,只有在高Mn含量(8％和17％)样品中存在着Mn₄Si₇化合物物相.而XANES结果则显示,对于Mn浓度在0.7%到17%之间的Mn_xSi_1-x样品,其Mn原子的XANES谱表现出了一致的谱线特征.基于多重散射的XANES理论计算进一步表明,只有根据Mn₄Si₇模型计算出的理论XANES谱才能够很好的重构出Mn_xSi_1-x样品的实验XANES谱.这些研究结果说明在Mn_xSi_1-x样品中,Mn原子主要是以镶嵌式的Mn₄Si₇化合物纳米晶颗粒存在于Si薄膜介质中,几乎不存在间隙位和替代位的Mn原子. 关键词： xSi_1-x磁性薄膜')" href="#">Mn_xSi_1-x磁性薄膜 分子束外延 XRD XANES     

脉冲激光沉积法制备的Ni1-xFexO稀磁半导体的结构和磁性研究

利用脉冲激光沉积方法制备出了具有室温铁磁性的Ni_1-xFe_xO(x=0.02,0.05)稀磁半导体.X射线衍射(XRD)结果表明Ni_1-xFe_xO的晶体结构为NaCl结构,并且在Fe含量较高的Ni_0.95Fe_0.05O中出现了少量的α-Fe₂O₃物相.X射线吸收近 关键词： 1-xFe_xO')" href="#">Ni_1-xFe_xO XANES 脉冲激光沉积方法     

薄膜厚度对La1.85Sr0.15CuO4薄膜结构和超导电性的影响

使用直流同轴磁控溅射法,在SrTiO₃(STO)衬底上成功制备出c取向的La_1.85Sr_0.15CuO₄(LSCO)超导薄膜.通过电输运测量系统和X射线衍射仪研究了薄膜厚度对LSCO(x＝0.15)薄膜电学性质和晶体结构的影响.实验证明随着膜厚增加,(006)衍射峰的半高宽(Full Width at Half Maximum,FWHM)逐渐减小,薄膜的取向性增强,与此同时,薄膜的超导转变温 关键词： 1.85Sr_0.15CuO₄薄膜')" href="#">La_1.85Sr_0.15CuO₄薄膜 超导电性 晶体结构     

Structural and optical properties of Ba(Ti1−x,Nix)O3 thin films prepared by sol–gel process

Ba(Ti_1−x,Ni_x)O₃ thin films were prepared on fused quartz substrates by a sol–gel process. X-ray diffraction and Raman scattering measurements showed that the films are of pseudo-cubic perovskite structure with random orientation and the change of lattice constant caused by Ni-doping with different concentrations is very small. Optical transmittance spectra indicated that Ni-doping has an obvious effect on the energy band structure. The energy gap of Ba(Ti_1−x,Ni_x)O₃ decreased linearly with the increase of Ni concentration. It indicates that the adjusting of band gap can be achieved by controlling the Ni-doping content accurately in Ba(Ti_1−x,Ni_x)O₃ thin films. This has potential application in devices based on ferroelectric thin films.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.     

Preparation, structure and ferromagnetic properties of the nanocrystalline Ti1-xMnxO2 thin films grown by radio frequency magnetron co-sputtering

This paper reported that the Mn-doped TiO2 films were prepared by radio frequency （RF） magnetron cosputtering. X-ray diffraction measurements indicate that the samples are easy to form the futile structure, and the sizes of the crystal grains grow big and big as the Mn concentration increases. X-ray photoemlssion spectroscopy measurements and high resolution transmission electron microscope photographs confirm that the manganese ions have been effectively doped into the TiO2 crystal when the Mn concentration is lower than 21%. The magnetic property measurements show that the Ti1-xMnxO2 （x = 0.21） films are ferromagnetic at room temperature, and the saturation magnetization, coercivity, and saturation field are 16.0 emu/cm^3, 167.5 × 80 A/m and 3740 × 80 A/m at room temperature, respectively. The room-temperature ferromagnetism of the films can be attributed to the new futile Ti1-xMnxO2 structure formed by the substitution of Mn^4＋ for Ti^4＋ into the TiO2 crystal .lattice, and could be explained by O vacancy （Vo）-enhanced ferromagnetism model.     

Pr0.7(Sr1-xCax)0.3MnO3多晶体系中的小极化子性质

采用基于柠檬酸体系的溶胶-凝胶法制备了Pr_0.7（Sr_1-xCa_x）_0.3MnO₃系列的多晶块材, 同时还用脉冲激光沉积技术（PLD）在SrTiO₃（100）衬底上外延生长了同一系列的薄膜, 系统研究了它们的晶格结构和电输运行为. 多晶和薄膜样品都具有正交晶格结构, 电输运行为在居里温度T_Ｃ以上的高温顺磁相都很好 关键词： 0.7（Sr_1-xCa_x）_0.3MnO₃')" href="#">Pr_0.7（Sr_1-xCa_x）_0.3MnO₃ 绝热小极化子模型 双交换作用 Jahn-Teller晶格畸变     

Structural characteristics and morphology of SmxCe1−xO2−x/2 thin films

Effect of the deposition temperature (200 and 500 °C) and composition of Sm_xCe_1−xO_2−x/2 (x = 0, 10.9–15.9 mol%) thin films prepared by electron beam physical vapor deposition (EB-PVD) and Ar⁺ ion beam assisted deposition (IBAD) combined with EB-PVD on structural characteristics and morphology/microstructure was investigated. The X-ray photoelectron spectroscopy (XPS) of the surface and electron probe microanalysis (EPMA) of the bulk of the film revealed the dominant occurrence of Ce⁴⁺ oxidation state, suggesting the presence of CeO₂ phase, which was confirmed by X-ray diffraction (XRD). The Ce³⁺ oxidation states corresponding to Ce₂O₃ phase were in minority. The XRD and scanning electron microscopy (SEM) showed the polycrystalline columnar structure and a rooftop morphology of the surface. Effects of the preparation conditions (temperature, composition, IBAD) on the lattice parameter, grain size, perfection of the columnar growth and its impact on the surface morphology are analyzed and discussed.     

脉冲偏压电弧离子镀CNx薄膜研究

用脉冲偏压电弧离子镀通过控制不同的氮流量在(100)单晶Si基片上制备了不同成分的CN_x薄膜.用光学显微镜,XPS,XRD,激光Raman和Nanoindenter等方法研究了薄膜的形貌、成分、结构和性能.结果表明,薄膜表面平整致密、氮含量随着氮流量的降低而降低、结构为非晶且为类金刚石薄膜;随着氮含量从18.9%降低到5.3%(摩尔百分比,全文同),薄膜的硬度和弹性模量单调增加而且增幅较大,其中硬度从15.0 GPa成倍增加到30.0 GPa;通过氮流量的调整能够敏感地改变薄膜中的sp³键的含量,是CN_x薄膜的硬度和弹性模量获得大幅度调整的本质原因. 关键词： x薄膜')" href="#">CN_x薄膜 脉冲偏压 电弧离子镀 硬度