ZnO纳米棒在聚［2-甲氧基-5-（2-乙基-己氧基）-1，4-苯撑乙烯撑］固态阴极射线发光器件中的应用研究

利用ZnO纳米棒阵列场发射电极,以SiO₂做为电子加速层制备了固态阴极射线器件,发光层为聚［2-甲氧基-5-（2-乙基-己氧基）-1,4-苯撑乙烯撑］（MEH-PPV）,在交流驱动下得到了MEH-PPV的固态阴极射线发光,探测到了长波峰和短波峰的发射,并和无电子加速层的器件做了比较,证明混合激发模式下的器件在长波长的发光亮度更大. 关键词： 固态阴极射线 ZnO纳米棒阵列 电子加速 电致发光     

氧化锌纳米颗粒薄膜的近紫外电致发光特性研究

利用溶胶-凝胶法(sol-gel method)制备了ZnO纳米颗粒薄膜(ZnO nanoparticle film),并以此为发光层制备了结构为ITO/ZnO nanoparticle/MEH-PPV/LiF/Al的电致发光器件.通过调整器件发光层厚度,对器件的发光光谱和电学特性进行测试研究,发现该器件在一定的直流电压下可以得到以ZnO近紫外(中心波长390 nm)发光为主的电致发光光谱,显示出较好的ZnO近紫外电致发光特性.对该器件的发光机理进行了一定的研究,认为该器件的发光是基于载流子隧穿.     

MOCVD法制备的p-ZnO/n-SiC 异质结器件及其电致发光性能

采用光辅助金属有机化学汽相沉积(PA-MOCVD)法在n-SiC(6H)衬底上制备出As掺杂的p型ZnO薄膜,并制备出相应的p-ZnO:As/n-SiC异质结器件。X射线衍射(XRD)和光致发光(PL)测试表明,ZnO薄膜具有较好的结构和光学特性。电流-电压(I-V)测试结果表明,该型异质结器件具有良好的整流特性,开启电压为5.0 V,反向击穿电压约为-13 V。正向偏压下,器件的电致发光(EL)谱表现出两个分别位于紫外和可见光区域的发光峰,通过和ZnO、SiC的PL谱对照,证实异质结器件的发光峰来源于ZnO侧的辐射复合。     

多环类苝四甲酸二酐插入层对ZnO纳米棒和聚合物复合太阳电池性能的影响

以ZnO纳米棒和聚[2-甲氧基-5-(2-乙基-己氧基)-1,4-苯撑乙烯撑](MEH-PPV)的复合体系作为光敏层制备了太阳电池.为了增大电池的光吸收,在ZnO纳米棒与MEH-PPV之间插入了有机n型小分子多环类苝四甲酸二酐(PTCDA),制备了不同厚度的PTCDA、结构为ITO/ZnO纳米棒/PTCDA/MEH-PPV/Au的太阳电池.实验发现,插入PTCDA后,电池在可见光区的吸收增强,光生激子数量增大,光电流密度增大.当蒸镀的PTCDA厚度为40 nm时,薄膜的粗糙度适中,表面形貌较为平滑,器件性 关键词： 有机太阳电池 ZnO纳米棒 聚合物     

富硅氮化硅／c—Si异质结中的电流输运机理研究

采用对靶磁控溅射方法在P型晶体硅（c—Si）衬底上沉积n型富硅氮化硅（SiNx）薄膜,形成了富硅SiNx／c—Si异质结．异质结器件呈现出较高的整流比,在室温下当V=4-2V时为1．3×10^3．在正向偏压下温度依赖的J—V特性曲线可以分为三个明显不同的区域．在低偏压区载流子的输运满足欧姆传输机理,在中间偏压区的电流是由载流子的隧穿过程和复合过程共同决定的,在较高偏压区的电输运以具有指数陷阱分布的空间电荷限制电流（SCLC）传输机理为主．     

MEH-PPV/ZnO纳米晶无机有机复合电致发光器件的研究

以Ⅱ一Ⅵ族无机半导体ZnO纳米颗粒为电子传输层,MEH-PPV为空穴传输层兼发光层,得到的电致发光器件比单层MEH-PPV器件的发光亮度和效率都明显提高。器件结构为ITO／MEH-PPV／ZnO／Al的电致发光光谱同单层PPV器件的光谱出现了不同,在620nm处出现了一个小的发光峰,应该是ZnO的发光。另外,双层结构器件的启亮电压由单层器件的9V降到了4V左右。由I-V曲线及发光光谱可判断出发光区域应在MEH-PPV／ZnO界面处,并且复合区域可能随着电压的变化而变化。     

基于MEH-PPV/ZnSe纳米复合器件的电致发光特性的研究

以巯基乙酸作为稳定剂在水相中制备了ZnSe纳米晶,用X射线粉末衍射(XRD)和X射线光电子能谱(XPS)对其进行了表征。用表面活性剂将ZnSe纳米晶从水相中转移到有机相中,使其与聚合物MEH-PPV复合作为发光层,制备了多层电致发光器件Glass/ITO/MEH-PPV∶ZnSe/BCP/Alq₃。对ZnSe纳米晶和MEH-PPV薄膜的光致发光谱及其吸收光谱的比较表明ZnSe纳米晶和MEH-PPV之间存在着能量传递,这是导致纳米复合薄膜的光致发光光谱和电致发光光谱存在差异的原因之一。文章对其在光激发和载流子注入条件下的不同发光机制进行了讨论。通过对器件的光电特性进行研究,发现ZnSe纳米晶发光的比例随着外加电压的增加而增加,而且器件的I-V特性基本上符合二极管的特性。     

基于量子点和MEH-PPV的白光发光二极管的研究

利用无机纳米材料与有机聚合物材料相结合的方法制备白光发光二极管器件, 研究了蓝光量子点QDs(B)掺杂聚[2-甲氧基-5-(2-乙基己氧基-1, 4-苯撑乙烯撑](MEH-PPV) 复合体系的发光特性及量子点QDs(B) 掺杂浓度(质量分数)不同对器件发光特性的影响. 制备了ITO/PEDOT:PSS/MEH-PPV:QDs(B)/LiF/Al 结构的电致发光器件, 测试了器件的电致发光光谱和电学、光学特性. 当QDs掺杂浓度为40%, 驱动电压为8 V时器件能得到较为理想的白光发射. 同时, 对比研究了非掺杂体系的发光特性, 制备了结构为ITO/PEDOT:PSS/MEH-PPV/QDs(B)/LiF/Al的器件, 掺杂体系相较于非掺杂体系, 器件的最大亮度增大, 启亮电压降低, 并分析了掺杂体系器件性能改善的原因.     

ZnO/P-Si异质结的光电特性研究

利用脉冲激光沉积方法在P-Si(100)衬底上生长ZnO薄膜,制备ZnO/P-Si异质结,研究衬底温度对异质结光电特性的影响.结果表明,在400℃,500℃,550℃和600℃下生长ZnO制备的异质结都有一定的整流特性,反向暗电流随着衬底温度的升高略有增加,在550℃下制备的样品具有最明显的光电效应.ZnO/P-Si异质结对可见光和紫外光呈现出不同的响应性.在可见光照射下,光电流随反向偏压急剧增大,偏压增大到某一值时,光电流增速变小,而在紫外光下,光电流有逐渐增大的趋势.根据ZnO的透射谱认为,可见光和紫外光是异质结不同的耗尽区诱导电子-空穴对产生光电流的.     

衬底位置对化学气相沉积法制备的磷掺杂p型ZnO纳米材料形貌和特性的影响

采用化学气相沉积方法,在无催化剂的条件下,通过改变衬底位置在Si(100)衬底上制备出了高取向的磷掺杂ZnO纳米线和纳米钉.测试结果表明,当衬底位于反应源上方1.5 cm处时,所制备的样品为钉状结构,而当衬底位于反应源下方1 cm处时样品为线状结构.对不同形貌磷掺杂ZnO纳米结构的生长机理进行了研究.此外,在ZnO纳米结构的低温光致发光谱中观测到了一系列与磷掺杂相关的受主发光峰.还对磷掺杂ZnO纳米结构/n-Si异质结I-V曲线进行了测试,结果表明,该器件具有良好的整流特性,纳米线和纳米钉异质结器件的开启电压分别为4.8和3.2 V.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.