120 W的二极管泵浦Nd:YAG绿光激光器

对激光二极管泵浦的NdYAG声光调Q腔内倍频固体激光器的折叠腔型进行了研究,当泵浦功率达800 W时,在V型腔上实现了脉宽为80 ns、重复频率为10 kHz、发散角为6 mrad、绿光功率为112 W的输出;在Z型腔上实现了脉宽为95 ns、重复频率为10 kHz、发散角为4 mrad、绿光功率为120 W的输出.比较两种腔型的实验结果可看出,Z型腔由于插入的光学元件较多,腔长较长,输出激光的脉宽较宽,但输出激光的光束质量有明显的提高.     

LD侧面泵浦Nd∶GdVO4 532 nm绿光激光器

为了获得高功率窄脉宽532 nm绿光激光输出,通过高重复频率声光驱动调Q技术和LD侧面泵浦Nd∶GdVO4技术,获得高功率线偏振1 064 nm激光输出。采用内腔倍频方式,对非线性晶体KTP进行频率变换,实现高功率窄脉宽绿光激光输出。在电源输入电流30 A,调Q驱动频率10 kHz的条件下,获得最高功率30 W线偏振1 064 nm激光输出,脉宽30 ns,倍频KTP晶体获得23.4 W的532 nm绿光输出,1 064 nm到532 nm转化效率为78%。实验结果表明:通过声光调Q技术和LD侧面泵浦Nd∶GdVO4技术,可以实现高功率线偏振窄脉宽1 064 nm激光输出,倍频非线性晶体KTP可获得高功率窄脉宽532 nm激光。     

LD侧面泵浦Nd:GdVO4 532 nm绿光激光器

为了获得高功率窄脉宽532 nm绿光激光输出,通过高重复频率声光驱动调Q技术和LD侧面泵浦Nd∶GdVO4技术,获得高功率线偏振1 064 nm激光输出.采用内腔倍频方式,对非线性晶体KTP进行频率变换,实现高功率窄脉宽绿光激光输出.在电源输入电流30 A,调Q驱动频率10 kHz的条件下,获得最高功率30 W线偏振1 064 nm激光输出,脉宽30 ns,倍频KTP晶体获得23.4 W的532 nm绿光输出,1 064 nm到532 nm转化效率为78％.实验结果表明:通过声光调Q技术和LD侧面泵浦Nd∶GdVO4技术,可以实现高功率线偏振窄脉宽1 064 nm激光输出,倍频非线性晶体KTP可获得高功率窄脉宽532 nm激光.     

高效率Nd:YVO4/LBO临界相位匹配脉冲绿光激光器

报道了一种利用激光二极管（LD）端面泵浦Nd:YVO4晶体,声光调Q,LBO临界相位匹配腔内倍频的高效率、小体积、风冷绿光激光器。分析了不同偏振光泵浦的情况下,激光晶体对泵浦光的吸收特性。由分析得出,采用部分偏振光泵浦,可以提高激光晶体对泵浦光吸收均匀性,改善基波畸变,获得高转换效率激光输出。实验中,在泵浦光功率为33 W、声光调Q重复频率为20 kHz时,得到脉宽为23.96 ns、平均功率为15 W的1064 nm基频光输出。经倍频后,得到平均功率为11.2 W的绿光输出,倍频效率为74.6%,总体光-光转换效率为34%。在输出功率为10 W时,测得1 h内输出功率不稳定度为0.512 2%,水平方向和竖直方向的光束质量因子M2分别为1.2和1.1。     

高效三倍频全固态Nd∶YAG/LBO紫外激光器

报道了一种侧面泵浦Nd∶YAG、声光调Q、LBO晶体腔外倍频和三倍频的355 nm准连续波紫外激光器.采用结构简单、紧凑的平-凹腔设计,在152 W的泵浦功率下,重复频率5 kHz时,获得平均功率1.62 W的355 nm TEM00模激光输出,三倍频的转换效率为25%;重复频率1 kHz时,获得平均功率518 mW、单脉冲能量518 μJ、脉宽17 ns、峰值功率高达30 kW的紫外激光输出.     

LD侧面泵浦电光调Q532nm脉冲激光器

 为了实现高可靠、窄脉宽、高峰值功率激光输出,采用侧面泵浦技术和电光调Q技术,设计出一种激光二极管侧面泵浦电光调Q全固态绿光激光器。采用结构简单、紧凑的平-平腔设计,其端镜和输出镜均为平面镜,获得较稳定的侧面泵浦Nd∶YAG腔外倍频KTP脉冲绿光激光输出。当泵浦电流为120A,重复频率为600Hz时,获得脉冲绿光的最高输出平均功率为3.62W,1064nm到532nm的转换效率为15.3%,其脉宽为21ns,峰值功率为300kW, 单脉冲能量为6.01mJ。实验结果表明：该激光器稳定性可靠,输出激光脉宽较窄、峰值功率高。     

可控制变频率微片激光器

 用20 W光纤耦合LD作为泵浦光源，对Nd^{3+sup>:YVO_{4/sub>微片进行了增益开关实验，获得了可控制变重复频率（1 Hz～25 kHz）的调Q激光输出。输出脉冲激光的宽度为16 ns，输出的峰值功率在几W。从速率方程出发进行了增益开关理论研究，通过数值解，分析了输出激光特性：当泵浦电流高于产生单脉冲的电流时，增加泵浦电流将在一个泵浦脉宽中出现多个激光脉冲输出；增加泵浦脉宽，将在一个泵浦脉宽中出现多个激光脉冲输出，泵浦脉宽越大，子脉冲个数越多；当增加重复频率时，输出与泵浦激光重复频率完全一致的激光脉冲，但也将在一个泵浦脉宽中出现多个激光脉冲输出。}}     

高效高稳定高光束质量声光调Q绿光激光器的研究

通过优化双棒串接直腔结构设计,利用大功率LD侧面抽运、声光Q开关、Ⅱ类相位匹配S-KTP内腔倍频获得高效大功率绿色激光输出.当抽运电流为45 A、重复频率为15 kHz时,激光平均功率为132 W,光—光转换效率为132％,脉宽约为120 ns.在输出130 W时,测得1 h功率不稳定度小于05%,光束质量因子M²为67.对高功率抽运情况下激光介质的热透镜效应以及谐振腔稳定运转工作区域也进行了理论分析和实验研究. 关键词： 绿光激光器 腔内倍频 声光调Q LD侧面抽运     

高效LD侧面泵浦腔外倍频绿光激光器

为满足激光加工、激光彩色显示、数据存储、医疗卫生和科研等领域对绿光激光器的需要,研制了一台高倍频效率、窄脉宽侧面泵浦腔外倍频的YAG/LBO绿光激光器。分析并计算了腔外最佳聚焦参数,确定了透镜的最佳聚焦焦距。实验中,利用808nm激光二极管侧面泵浦Nd:YAG晶体,使用BBO晶体进行加压式调Q,采用四分之一波片补偿Nd:YAG晶体的热退偏,最终实现了重复频率1kHz、输出功率10.7W的1 064nm输出,最大单脉冲能量为10.7mJ。在此基础上,采用Ⅰ类温度相位匹配LBO晶体对基频光进行腔外倍频,获得了重复频率1kHz、脉宽21ns、最大输出功率6.04W的532nm准连续绿光输出,倍频效率高达59.3%。     

脉冲单频Nd:YVO4激光器及其倍频输出特性研究

为了研制激光干涉成像所需的主振荡功率放大(MOPA)结构脉冲单频激光器,本文完成MOPA激光器的种子源即声光调Q脉冲单频1 064 nm激光器的特性研究,同时完成种子源腔外倍频绿光特性研究。脉冲单频激光器采用声光调Q模块实现脉宽约20 ns的1 064 nm脉冲激光输出,采用环形腔设计并采用一组不同厚度的标准具实现单纵模运转。实验研究基频1 064nm和倍频532 nm激光脉冲的线宽,得出在全脉宽范围内都具有较高时间相干性的结论。实验分别获得脉宽约28 ns峰值功率约6.5 kW的1 064 nm脉冲单频激光和脉宽约20 ns、峰值功率约0.5 kW的532 nm脉冲单频激光,腔外倍频效率为5.6%。实验同时也验证了腔外倍频的激光脉宽压缩效应。     

LD泵浦Nd∶YAG多波段激光器

为了获得高效率多波段激光输出,通过高重复频率驱动声光调Q技术和LD侧面泵浦技术,获得高功率高重频窄脉宽1.06 m激光输出。利用起偏器件获得垂直和水平两束1.06 m线偏振光,一束垂直线偏振光泵浦非线性晶体周期极化钽酸锂（PPLT）,实现1.46 m与3.9 m激光输出后与另一束1.06 m水平线偏振光合束,实现三波段共轴激光输出。在电源输入电流35 A、调Q驱动频率10 kHz的条件下,获得140 W的1.06 m激光。分束后泵浦PPLT获得最高功率为6.3 W的3.9 m和8.6 W的1.46 m激光,差频转化效率为21.3%。试验结果表明:通过高重频声光调Q技术和LD侧面泵浦技术,可以实现高重频窄脉宽1.06 m光输出,泵浦PPLT可获3.9 m和1.46 m激光输出。     

High-Power Continuous-Wave and Acousto-Optical Q-Switched Ho:(Sc_(0.5)Y_(0.5))_2SiO_5 Laser Pumped by Laser Diode

We experimentally investigate the continuous-wave(cw)and acousto-optical(AO)Q-switched performance of a diode-pumped Ho:(Sc_(0.5)Y_(0.5))_2SiO_5(Ho:SYSO)laser.A fiber-coupled laser diode at 1.91m is employed as the pump source.The cw Ho:SYSO laser produces 13.0 W output power at 2097.9 nm and 56.0%slope efficiency with respect to the absorbed pump power.In the AO Q-switched regime,at a pulse repetition frequency of 5 kHz,the Ho:SYSO laser yields 2.1 mJ pulse energy and 21 ns pulse width,resulting in a calculated peak power of 100 k W.In addition,at the maximum output level,the beam quality factor of the Q-switched Ho:SYSO laser is measured to be about 1.6.     

A High Conversion Efficiency Q-Switched Intracavity Nd:YVO_4/KTA Optical Parametric Oscillator under Direct Diode Pumping at 880nm

We report a high conversion efficiency Q-switched Nd:YVO_4/KTiOAsO_4(KTA) intracavity optical parametric oscillator(IOPO) operating near 3.5 um based on direct 880 nm laser diode(LD) pumping. A maximum average idler output power of 2.6 W with a pulse width of about 7.9 ns is achieved under an absorbed LD power of 45.4 W at a pulse repetition rate(PRR) of 10 kHz. The maximum optical-optical conversion efficiency from LD power to OPO mid-infrared(MIR) output of 6.74% is achieved. To our knowledge, this is the highest conversion efficiency for a KTA-IOPO by exploiting a Q-switched laser as the parent fundamental pump source. The beam quality factors M~2 of the MIR beam at the full output power with a PRR of 10 kHz are within 2.12 in both the horizontal and vertical directions, indicating a near Gaussian mode.     

High-power dual-rod Yb:YAG laser

We describe a diode-pumped Yb:YAG laser that produces 1080 W of power cw with 27.5% optical optical efficiency and 532 W Q-switched with M(2)=2.2 and 17% optical-optical efficiency. The laser uses two composite Yb:YAG rods separated by a 90 degrees quartz rotator for bifocusing compensation. A microlensed diode array end pumps each rod, using a hollow lens duct for pump delivery. By changing resonator parameters we can adjust the fundamental mode size and the output beam quality. Using a flattened Gaussian intensity profile to calculate the mode-fill efficiency and clipping losses, we compare experimental data with modeled output power versus beam quality.     

Highly efficient in-band pumped Er:YAG laser with 60 W of output at 1645 nm

A high-power Er:YAG laser that is in-band pumped by a high-power cladding-pumped erbium-ytterbium codoped fiber laser operating at 1532 nm is reported. The Er:YAG laser produced 60.3 W of continuous-wave output at 1645.3 nm in a beam with M2 approximately equal to 3 for 82 W of incident pump power and 20 W of TEM00 output with M2 < 1.2 for 32.4 W of incident pump power. The slope efficiency with respect to incident pump power at pump powers of >20 W was approximately 81%. In the Q-switched mode of operation, a slightly modified resonator configuration incorporating an electro-optic Q switch produced pulses of approximately 4 mJ energy and approximately 100 ns (FWHM) duration, corresponding to a peak power of approximately 42 kW at a repetition rate of 1 kHz for an incident pump power of 16.8 W. The prospects for further improvement in continuous-wave and Q-switched performance are discussed.     

Diode-end-pumped 1D top-hat Nd:YVO4 slab laser

A one-dimensional (1D) top-hat, diode-end-pumped, electro-optically Q-switched Nd:YVO4 slab laser is demonstrated. Under the pump power of 175.5 W, 26.3-W output power is obtained with the repetition rate of 5 kHz and the pulse width of 4.3 ns. The output beam has a good top-hat beam profile in both the near field and the far field.     

脉冲LD泵浦电光调Q深紫外激光器

研制了千赫兹213 nm深紫外全固态激光器。激光器采用脉冲LD侧面泵浦方式和电光调Q技术,实现了10瓦级基频光的稳定输出。利用多次倍频技术,实现了稳定的213 nm深紫外激光输出。当LD泵浦电流为80 A时,213 nm激光输出的最大平均功率达到了151 m W,激光器重复频率为1 k Hz,激光脉冲宽度为10ns,功率不稳定度为3%。同时,对激光在非线性晶体中的偏振匹配和不同重复频率条件下的激光器运转特性进行了分析。     

A diode-pumped linear intracavity frequency doubled Nd:YAG rod laser with 40 ns pulse width and 73 W green output power

We analyzed a linear cavity for intracavity frequency doubling of a diode-pumped acousto-optic Q-switched Nd:YAG rod laser, and showed that a green laser beam with a short pulse width can be generated efficiently. A green laser output power of 73 W corresponding to the 83.9% of maximum IR output power was obtained with a 40 ns pulse width at a 10 kHz repetition rate. A green output power of 40 W with a 35 ns pulse width was measured at a 5 kHz repetition rate. Minimum laser pulse width of approximately 32 ns was obtained around 1 kHz repetition rate for both green and IR laser beams.     

200 W双谐振腔组合单向输出准连续绿光激光器

研究了最大平均输出功率达206 W的高功率准连续绿光激光器.利用ABCD定律及高斯光束在腔内的自再现条件,分析了激光晶体热透镜效应及热致双折射效应对谐振腔稳定性和输出光束质量的影响.实验中将两个型号相同的LD侧面泵浦激光模块分别置于一个平-凹V型谐振腔和一个平-凹直腔内,形成两束稳定运转的1 064 nm基频光,经过声光Q开关和倍频晶体后,产生两束倍频光,均到达平面折叠镜,最终由平面折叠镜单向重叠输出.当激光模块的泵浦电流为50 A,声光调Q的重复频率为22.4 kHz时,最大平均输出功率为206 W,最大单脉冲能量为9.2 mJ,脉冲宽度为201 ns,峰值功率为45.8 kW的532 nm绿光输出,倍频效率达到60.2%.激光器2 h工作的功率不稳定度优于2.5%.