Nb衬底MgB_2超导膜的韧性研究

用混合物理化学气相沉积法(hybrid physics-chemical vapor deposition简称为HPCVD)在Nb衬底上生原位制备了平均厚度是1.5μm的MgB2多晶膜样品,其起始超导转变温度Tc(onset)=39.37K,转变宽度ΔTc=0.45K.样品由大量六边型片状晶粒组成.对样品进行了韧性测试,可以发现膜在弯曲120°后,虽然弯曲面处出现了裂纹,但膜仍很牢固的附着在衬底上,其超导电性仍可保持.     

不锈钢衬底MgB2厚膜韧性的研究

我们用混和物理化学气相沉积法(HPCVD)在不锈钢衬底上原位制备了以MgB2厚膜(约10微米厚)为过渡层的MgB2超导厚膜(约20微米厚)样品,两层膜总厚约30微米.X光衍射实验表明过渡层为(101)取向的织构膜,表层MgB2超导厚膜接近多晶膜,但有较强(101)取向,两者均含有少量的Mg和MgO杂相.此超导厚膜样品的Tc(onset)=37.8K,Tc(zero)=36.6K,ΔT=1.2K.对此样品的弯曲实验表明,以曲率半径500微米弯曲到180°后,样品仍具有Tc(onset)=37.8K,Tc(zero)=36.4K的超导电性.样品剖面SEM观测表明该膜结构致密,表面厚膜层和过渡层之间连接紧密.样品表面的SEM观测表明虽然样品弯曲导致表面MgB2超导厚膜面出现了裂缝,甚至有小部分膜面的脱落,但过渡层始终紧紧附着在不锈钢衬底上.这表明过渡层MgB2厚膜的存在大大地提高样品整体的柔韧性,展现了不锈钢衬底上的MgB2厚膜超导带(线)巨大的开发潜力和诱人的广阔应用前景.     

初探混合物理化学气相沉积法(HPCVD)制备不锈钢衬底MgB2超导厚膜样品

介绍用混合物理化学气相沉积法(HPCVD)制备的不锈钢衬底MgB2超导厚膜样品.该样品的Tc(onset)=38K,Tc(0)=27K.X光衍射图形表明它是(101)方向织构的致密厚膜.这种膜具有较强的韧性,同时和衬底有高度的结合性.当其被弯曲到约200微米半径的弧度时,膜面会出现条状裂纹,但仍有少部分膜面未被破坏,保持完整,表现出较好的韧性.     

(0001)SiC衬底MgB_2超薄膜的制备和性质研究

利用混合物理化学气相沉积法(Hybrid physical-chemical vapor deposition简称为(HPCVD)在(0001)SiC衬底上制备了干净的MgB2超导超薄膜.在背景气体、压强、载气氢气流量以及B2H6的流量一定的情况下,改变沉积时间,制得一系列MgB2超薄膜样品。通过观察样品的表面形貌变化探究了MgB2超薄膜的生长过程.该系列超薄膜的生长遵循Volmer-Weber岛状生长模式且沿c轴外延生长.以20nm超薄膜作为例子,可知其表面连接性良好,超导转变温度Tc(0)≈38.5K,临界电流密度Jc≈0.82×107 A/cm2,表明了利用HPCVD在(0001)SiC衬底上制备的MgB2超薄膜有很好的性能.这预示其在超导电子器件上具有广阔的应用前景.     

MgB2超导晶须的研究

本文报道了用混合物理化学气相沉积法(hybrid physical-chemical vapor deposition,简称为HPCVD)在铜衬底上生长出了MgB2超导晶须.这些晶须几乎都是以垂直或接近垂直于衬底表面生长,互不接触.M～T测量给出了这些MgB2晶须的磁超导转变温度是39.0 K,但无法测得其具有超导转变温度值的R～T曲线.经过与铜衬底MgB2超导膜的相关数据比较和计算也确认了这些MgB2超导晶须的确实性.     

c轴取向SiC衬底MgB_2超导厚膜的制备及性质

通过混合物理化学气相沉积法(Hybrid Physical-chemical Vapor Deposition,简称HPCVD),我们在SiC衬底上制备出了c取向8μm厚的MgB2超导厚膜.电性质测量表明其起始超导转变温度是41.4K,转变宽度为0.5K,剩余电阻比率RRR～7.磁性质测量表明5K和零场下样品的临界电流密度达到了1.7×106A/cm2.     

混合物理化学气相沉积法制备Al2O3衬底MgB2薄膜性质的研究

我们用混合物理化学气相沉积(Hybrid Physical-Chemical Vapor Deposition简称为HPCVD)法在Al2O3(00l)衬底上原位制备了MgB2超导薄膜样品.样品厚度约为1μm左右,最高的超导起始转变温度Tc(onset)＝40.3K,转变宽度ΔT为0.3K.ρ50K=2.3μΩcm,剩余电阻比率RRR=R300K/R50K=10.样品的X射线衍射分析表明,MgB2薄膜具有较好的c轴取向,晶粒大小约200nm.由毕恩模型计算求得在5K和零场条件下,样品的临界电流密度Jc=7.6×106A/cm2,不同磁场下测得R～T曲线可以外推得到Hc2(0K)约10T.这些结果表明HPCVD技术在MgB2薄膜原位制备方面有着很大的优势,从而有利于实现MgB2薄膜在电子器件方面的应用.     

混合物理化学气相沉积法制备蓝宝石衬底外延MgB2薄膜性质的研究

我们用混合物理化学气相沉积(Hybridphysicalchemicalvapordeposition简称为HPCVD)法在αAl2O3(00l)衬底上原位制备了一批超导性能良好的外延MgB2超导薄膜样品.用10%浓度的乙硼烷(B2H6)氢气混合气作为原料,研究了不同条件对MgB2薄膜沉积速率的影响.在一定条件下制备了一批MgB2薄膜,厚度为200nm左右,样品的零电阻转变温度(Tc0)最高达到39K.X射线衍射分析的θ～2θ扫描表明,MgB2薄膜的晶粒都具有较好的C轴取向,对样品的(101)面Φ扫描结果显示MgB2薄膜晶格与衬底有很好的外延取向,取向关系为[1010]MgB2∥[1120]Al2O3.由毕恩模型计算求得在5K和零场条件下,样品的临界电流密度Jc=9.8×106A/cm2.这些结果表明HPCVD技术在MgB2外延薄膜原位制备方面有着很大的优势,从而有利于实现MgB2薄膜在电子器件方面的应用.     

纳米粒子在不锈钢衬底MgB2超导膜中的作用

我们用混合物理化学气相沉积法(hybrid physical-chernical vapor deposition简称为HPCVD)以氩气为背景气体,在不锈钢衬底上于不同条件下制备了一批MgB2超导薄膜样品.用扫描电子显微镜获取了相关的SEM图像,并对膜的成分进行了能谱分析(EDX)的.当把不锈钢衬底MgB2超导薄膜弯曲不同角度之后,膜面上均出现了裂纹.裂纹的数量和宽度随弯曲的角度的增大而增加,但是膜始终紧紧地覆着在衬底上不脱落.因此我们可以说覆着在不锈钢衬底上的MgB2超导薄膜具有了很好的韧性.在膜中我们也发现有大量的数十纳米大小的晶粒.这个尺寸的纳米粒子的作用可以用来平衡MgB2膜内结构和表面晶粒的活性之间的相互作用.MgB2纳米粒子的存在是MgB2超导膜表现出韧性的关键角色.     

不同厚度的MgB_2超薄膜的制备和性质研究

本文报导了利用混合物理化学气相沉积法(Hybrid physical-chemical vapor deposition,HPCVD)在SiC(0001)衬底上制备干净的MgB2超薄膜.在背景气体压强、载气H2流量等条件一定的情况下,改变B2H6流量及沉积时间,制备不同厚度的MgB2超薄膜样品,并研究了超导转变温度Tc、剩余电阻率ρ(42K)、上临界场Hc2等与膜厚的关系.这系列超薄膜生长沿c轴外延,随膜厚度的变小Tc(0)降低,ρ(42K)升高.膜在衬底上的生长遵循Volmer-Weber岛状生长模式.对于10nm厚的膜,Tc(0)~32.4K,ρ(42K)~124.92μΩ·cm,其表面连接性良好,平均粗糙度为2.72nm,上临界磁场Hc2(0K)~12T,零场4K时的临界电流密度Jc~107A/cm2,为迄今为止所观测到的10nm厚MgB2超薄膜的最高Jc值,这也证明了10nm厚的MgB2膜在超导纳米器件上具有很强的应用潜力.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.