CSNS-II超导椭球腔失谐研究

中国散裂中子源二期束流功率升级到500 kW，直线加速器H-的能量增益由现在的80 MeV提高到300 MeV以上，其中150 ~ 300 MeV能量段采用648 MHz β_g=0.60的5-cell超导椭球腔结构。超导椭球腔具有加速梯度高、结构简单、后处理容易等优点，缺点是结构强度弱、易失谐。本文主要研究该椭球腔的失谐特性。利用COMSOL Multiphysics软件进行了计算分析，在两端固定边界条件下，裸腔的氦压敏感性系数K_P=–45.705 Hz/mbar(1 mbar=100 Pa)，洛伦兹力失谐因子K_L=1.574 Hz/(MV/m)2。增加加强环并优化其位置来改善氦压敏感性系数和洛伦兹力失谐因子，通过计算分析最终确定选择双加强环方案来减小椭球腔的失谐。两个加强环位置分别取在75和120 mm的位置，腔体失谐的改善最大，K_P=6 Hz/mbar，K_L=0.43 Hz/(MV/m)2。为了更准确地计算椭球腔的氦压敏感性系数和洛伦兹力失谐因子，本文引入调谐刚度边界条件进行失谐分析，在椭球腔调谐器端设置30 kN/mm边界条件，另一端固定，计算得到氦压敏感性系数为4.8 Hz/mbar，洛伦兹力失谐因子1.99 Hz/(MV/m)2，满足工程要求。另外，用CST软件对椭球腔的动态洛伦兹力失谐进行了初步分析，用软件Workbench计算了椭球腔的振动本征频率，结果显示，振动本征频率离射频脉冲重复频率及环境振动频率较远，不易发生共振失谐。     

中国散裂中子源二期648 MHz超导腔调谐器设计

中国散裂中子源二期升级采用超导腔技术方案,其中在165～300 MeV能量段采用648 MHz 6-cell超导腔模组,每个模组中集成3只6-cell超导腔。超导腔工作在脉冲模式,为了保证超导腔2 K下的频率满足运行要求,每只超导腔需要一套低温调谐器对其频率进行精确调节控制。针对648 MHz 6-cell超导腔的结构和运行特点进行了低温调谐器的设计,采用快慢组合机构补偿超导腔的频率偏移,对调谐器的基本性能和超导腔脉冲模式运行下的动态洛伦兹失谐进行了分析。     

低β 162.5 MHz taper型HWR腔的机械性能分析（英文）

北京大学正在设计β=0.09,频率为162.5 MHz taper型的二分之一波长射频超导谐振腔(HWR腔),这种腔针对高流强质子束(约100mA)和氘束(约50mA)的加速而设计。对于这种超导腔而言机械性能分析是十分重要的,可以通过机械性能分析来估计由于腔体的形变带来的频率偏移。用ANSYS分析了由于液氦压力不稳定造成的麦克风效应以及洛伦兹力造成的腔体失谐,并且对沿腔体轴线方向的调谐进行了分析。模拟结果显示这只腔压力敏感系数为31.1 Hz/kPa,洛伦兹力系数为-0.41Hz/(MV·m~(-1))~2。腔体的调谐范围达到±177kHz,足够补偿腔体可能的频率偏移。腔体的机械性能满足腔体正常运行的要求。     

低β162.5 MHz taper型HWR腔的机械性能分析（英）

北京大学正在设计=0.09, 频率为162.5 MHz taper型的二分之一波长射频超导谐振腔（HWR腔）, 这种腔针对高流强质子束（约100 mA）和氘束（约50 mA）的加速而设计。对于这种超导腔而言机械性能分析是十分重要的, 可以通过机械性能分析来估计由于腔体的形变带来的频率偏移。用ANSYS分析了由于液氦压力不稳定造成的麦克风效应以及洛伦兹力造成的腔体失谐, 并且对沿腔体轴线方向的调谐进行了分析。模拟结果显示这只腔压力敏感系数为31.1 Hz/kPa, 洛伦兹力系数为－0.41 Hz/(MVm-1)2。 腔体的调谐范围达到177 kHz, 足够补偿腔体可能的频率偏移。腔体的机械性能满足腔体正常运行的要求。     

北京大学光阴极注入器3+1/2超导腔机械性能

 介绍了北京大学光阴极注入器的核心部件3+1/2超导腔的机械性能的设计，通过ANSYS和SUPERFISH程序优化加强筋的个数和位置，解决了超导腔在脉冲条件下由于洛仑兹力引起的超导腔失谐以及当超导腔进行低温调谐时场平滑度变化过大的问题，同时针对复杂超导腔结构进行了低温调谐结构的设计。     

含色散介质的一维光子晶体微腔中简正耦合模的物理图像

对一维光子晶体中的色散介质采用洛伦兹振子模型,对线性层及色散δ层均采用传输矩阵的方法,研究了一维含色散介质的光子晶体微腔中的简正耦合模.通过改变洛伦兹振子和微腔之间的失谐频率,分析了简正耦合模频率的变化情况.在失谐频率比较大时,光与洛仑兹振子间的耦合作用较小,简正耦合模中的一个接近腔模频率,而另一个则接近洛仑兹振子的共振频率;在失谐频率比较小时,光与洛仑兹振子间的耦合作用较大,简正耦合模与未耦合的腔模频率和洛仑兹振子的共振频率之间的差别较为明显.最后通过引进该结构的复有效折射率,对含色散介质的系统,由于带隙中间的共振模被湮灭并分裂为左右两个耦合模,其复有效折射率虚部在原共振峰处跃变为一较大值,而在新生成的两个耦合模附近趋近于零,光与色散介质相互耦合而形成的腔极化激元的物理图像十分清晰.     

CFETR TF高场导体的横向几何特征分析

聚变堆用超导磁体性能衰退与超导丝断裂有关,其宏观表现为股线发生横向位移。对一种高性能CICC导体进行极限电磁性能测试,观测到导体性能发生显著衰退。通过FiJi软件对不同磁场下导体进行横向几何特征分析。结果表明,随磁场增加,洛伦兹力使得股线从低压区向高压区迁移,局部空隙率发生变化,并且整体股线向洛伦兹力方向迁移。     

腔光力系统制备微波非经典态研究进展

腔光力系统作为一种新型的混合量子系统,因其超强耦合度、低温超导条件下极低的噪声、较长的相干时间等优势而成为被广受关注的量子实验平台.本文简要介绍腔光力学及腔光力系统基本原理,对常见腔光力系统进行分类,详细介绍利用广义腔光力系统进行微波非经典量子态制备的相关进展,对其性能优势和待解决问题进行分析,最后总结相关应用场景并对未来的潜在应用领域进行了展望.     

BEPCⅡ超导腔静态热负荷和无载品质因数Q_0的测量

超导腔的静态热负荷和无载品质因数是表征超导腔低温恒温器以及超导铌腔性能好坏的最重要参数.BEPCⅡ超导腔采用的是液氨浸泡冷却方式,对两个超导腔在测试站分别进行了降温调试,在超导腔达到超导状态并稳定运行后,对其静态热损耗进行了测定.此外,超导腔Q_0的测量主要是采用热力学的方法测量其高频损耗然后经计算得出Q_0.介绍了BEPCⅡ超导腔静态热负荷和无载品质因数的测量原理及方法,并且给出了两个超导腔在不同高频加速电压下的测试结果.此测试结果已作为BEPCⅡ超导腔验收测试的重要依据.     

BEPCⅡ超导腔静态热负荷和无载品质因数Q0的测量

超导腔的静态热负荷和无载品质因数是表征超导腔低温恒温器以及超导铌腔性能好坏的最重要参数.BEPCⅡ超导腔采用的是液氦浸泡冷却方式,对两个超导腔在测试站分别进行了降温调试,在超导腔达到超导状态并稳定运行后,对其静态热损耗进行了测定.此外,超导腔Qo 的测量主要是采用热力学的方法测量其高频损耗然后经计算得出Qo.介绍了BEPCⅡ超导腔静态热负荷和无载品质因数的测量原理及方法,并且给出了两个超导腔在不同高频加速电压下的测试结果.此测试结果已作为BEPCⅡ超导腔验收测试的重要依据.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.