改进的TESLA式高阶模衰减器的实验研究

讨论了TESLA型高阶模耦合器的改进, 对所设计的改进型TESLA式高阶模耦合器进行实验, 对理论计算与实验结果进行详细分析, 结果表明改进的高阶模耦合器理论计算和实验结果符合得较好.     

2-cell超导腔的高阶模分析

 阐述了2-cell Telsa腔的设计。用3维程序HFSS分析了其高阶模的特点，给出了高阶模的主要参数频率、品质因数、分路阻抗以及模式的电场分布，并且π模的电场分布与Superfish的模拟结果相比较，两者是一致的。最后，简要分析了各高阶模对电子加速的影响，分析表明高阶模降低了电子加速效率和束流的稳定性。     

The First Nine-Cell TESLA Cavity Made in China

A totally home-made 9-cell TESLA type superconducting cavity is mane at Peking University. The cavity abrication is according to DESY specification. The cavity is made of high purity niobium from OTIC, Ningxia. The electron beam welding is carried out at Harbin Institute of Technology, Harbin. By the cooperation, the cavity is tested at Thomas Jefferson National Accelerator Facility, USA. The preliminary result shows the acceleration gradient Eacc is 23 MV/m without quench and has potential for improvement.     

Tuning for the first 9-cell TESLA cavity of PKU

A method based on circuit model is used to tune the first home-made 9-cell TESLA type superconducting niobium cavity at Peking University. After tuning, a flat field profile with a final π-mode frequency within 3 kHz of target frequency is achieved. The field flatness is measured by a bead-pull method, and the relative electric field is calculated from the frequency shift perturbed by the bead stepping along the axis of the cavity.     

Cold RF test and associated mechanical features correlation of a TESLA-style 9-cell superconducting niobium cavity built in China

The RF performance of a 1.3 GHz 9-cell superconducting niobium cavity was evaluated at cryogenic temperatures following surface processing by using the standard ILC-style recipe. The cavity is a TESLA-style 9-cell superconducting niobium cavity, with complete end group components including a higher order mode coupler, built in China for practical applications. An accelerating gradient of 28.6 MV/m was achieved at an unloaded quality factor of 4×10⁹. The morphological property of mechanical features on the RF surface of this cavity was characterized through optical inspection. Correlation between the observed mechanical features and the RF performance of the cavity is attempted.     

太阳能自动跟踪系统的探索与实验

介绍了“多元法”太阳自动跟踪系统的原理，并就其实现的可能性进行了探索，模拟试验结果证明该系统是可行的。     

Lorentz detuning and tuning system study of 3+1/2cell DC-SC photo-injector for PKU-FEL

A 3+1/2cell DC-SC photo-injector for PKU-FEL facility is under development,which is an upgrade design of the successful 1+1/2cell DC-SC photo-injector. The Lorentz detuning and tuning structure for the 3+1/2cell superconducting cavity is presented in this paper. The Lorentz force detuning coefficient is 1.2Hz/(MV/m)² with double stiffening rings for the half cell and single stiffening rings between the adjacent TESLA cells. With the special stiffening structure, the 3+1/2cell whole cavity needs only one tuner. The influences of the tuning on frequency shift, field flatness and average gradient are discussed in this paper. The simulation results show that the stiffening rings' design is successful.     

紧凑型高平均流强光阴极注入器

根据北京大学1+1/2单元超导腔直流--超导(DC-SC)光阴极注入器的实验研究结果, 证明了这种新型光阴极注入器的可行性, 在此基础上对这种新型注入器进行了升级设计, 使之成为实用的紧凑型高平均流强的光阴极注入器, 为北京大学自由电子激光装置提供品质良好的电子束流. 给出了升级的3+1/2单元超导腔注入器的详细设计, 包括注入器核心结构的电磁场设计、束流动力学模拟、机械设计. 并对整个注入器的恒温器进行了初步设计.     

北京大学光阴极注入器3+1/2超导腔机械性能

 介绍了北京大学光阴极注入器的核心部件3+1/2超导腔的机械性能的设计，通过ANSYS和SUPERFISH程序优化加强筋的个数和位置，解决了超导腔在脉冲条件下由于洛仑兹力引起的超导腔失谐以及当超导腔进行低温调谐时场平滑度变化过大的问题，同时针对复杂超导腔结构进行了低温调谐结构的设计。     

9-cell TESLA超导加速腔研制中Dumb-Bells的测量与调整

为了保证9-cell超导加速腔在场的平滑度、TM010模的频率以及加速器的总长度达到TESLA国际标准, 必须确保每个Dumb-Bell在以上各方面达到标准要求. 由于冲压、机加工以及电子束焊接等过程会引起形变, 因此, 必须在完成iris和加强筋的电子束焊接之后对Dumb-Bells进行微波和机械测量, 并根据测量的结果对其腔形和长度等作必要的调整. 北京大学已经建立了一套完整的测量和调整Dumb-Bells的装置, 本文深入研究了Dumb-Bells的测量与调整的方法.