光抽运半导体激光器增益特性研究

以InGaAs/GaAs应变量子阱材料为例,介绍了考虑能带及波函数的混合效应的6×6Luttinger-Kohn哈密顿量,提出用有限差分法求解含Luttinger-Kohn哈密顿量的有效质量方程,数值模拟得到导带和价带的能带结构,计算应变量子阱的跃迁矩阵元,进而用Lorentzian线形函数计算材料增益。讨论了量子阱阱宽、注入载流子浓度、温度等因素对量子阱材料增益的影响。计算结果表明,压应变使得量子阱有效带隙增大,降低了材料增益的透明电流密度,继而降低器件的阈值,改善器件的输出特性;增益峰值波长和发射波长之间合适的偏差,会使光抽运半导体激光器的阈值电流和工作电流随温度有较小的变化。     

PbTe/CdTe量子阱光学性质的研究

PbTe/CdTe量子阱是一类新型异系低维结构材料,实验观察到具有强的室温中红外光致发光现象.建立了理论模型,计算了PbTe/CdTe量子阱的自发辐射率和光学增益.模型中量子阱分立能级的计算采用k·p包络波函数方法和有限深势阱近似,考虑了PbTe能带结构的各项异性和阱层中应变对能级的影响.计算了PbTe/CdTe量子阱自发辐射谱与带间弛豫和注入载流子浓度间的依赖关系,计算结果与实验观察到的光致发光峰相符合.自发辐射谱线峰位随着注入载流子浓度的增加而出现蓝移,当载流子浓度从2×1017cm-3增加到2.8×1018cm-3,基态发射峰从372 meV蓝移到397 meV,而第一激发态发射峰蓝移量为15 meV.上述蓝移现象是由载流子与载流子及载流子与声子间的相互作用引起的.与PbTe体材料相比.PbTe/CdTe量子阱结构具有更高的增益强度(提高近15倍)和更宽的增益区,因而该体系可能是实现室温连续工作的中红外激光器的理想材料.     

兼顾量子阱材料增益与折射率变化的研究

对比分析了量子阱材料增益谱及其折射率变化谱随阱宽、应变和载流子浓度的变化特性,在此基础上以两谱线3dB谱宽交叠区面积为度量,分析了各因素对兼顾材料增益与折射率变化的影响,并剖析了其中的物理机理。研究表明,两谱线3dB谱宽交叠区面积随阱宽的变化过程中存在一个极大值;引入压应变有利于增大交叠区面积;交叠区面积随载流子浓度单调增加的过程中存在一个转折点,在转折点之前增加迅速,在转折点之后增加放缓。基于以上影响规律,选取适当的阱宽与压应变量,在载流子浓度为3.0×10^(24) m^(-3)时,设计出的In0.583Ga0.417As/In0.817Ga0.183As0.4P0.6量子阱在C波段内可恰当地兼顾增益与折射率变化,两谱线3dB谱宽交叠区面积为3.7×10~4 nm/cm。     

InGaAsSb/AlGaAsSb长波长多量子阱激光器有源区的优化设计

系统地研究了波长为2.7μm的InGaAsSb/AlGaAsSb多量子阱激光器中有源区的优化设计.分别用含应变势的6带KP模型和抛物带模型计算价带和导带的能带结构，并得到薛定谔方程和泊松方程的自洽解，由此计算量子阱在载流子注入时的增益谱.研究表明制约量子阱增益的主要因素不是跃迁矩阵元，而是粒子数反转程度，尤其是空穴填充HH1子带的概率.增加压应变或减小阱宽都会提高量子阱增益.前者降低了价带HH1子带空穴的平面内有效质量；后者拉大了价带子带间距，尽管它同时略微增加了空穴有效质量.这两种因素都导致价带顶空穴态     

Ga1-xInxNyAs1-y/GaAs量子阱中电子-LO声子的散射率

在有效质量近似下利用打靶法求出Ga_1-xIn_xN_yAs_1-y/GaAs量子阱中的本征能级E_n, 并通过费米黄金规则计算电子-LO声子由第一激发态到基态的散射率和平均散射率随温度、阱宽以及氮(N)和铟(In)组分变化的规律. 计算结果表明: 在In 组分恒定的情况下, 随着N组分的增加, 散射率和平均散射率增加; 在N组分恒定的情况下, 随着In组分的增加, 散射率和平均散射率减小; 随着温度的增加, 在温度较低时散射率和平均散射率随温度的增加变化不大, 在温度较高时随温度的增加而增加; 随着阱宽的增加, 散射率和平均散射率都是先增加到一个最大值, 然后再减小, 最大值出现在阱宽200 Å附近. 计算结果对Ga_1-xIn_xN_yAs_1-y/GaAs量子阱在光电子器件应用方面有一定的指导意义. 关键词： 费米黄金规则 1-xIn_xN_yAs_1-y/GaAs量子阱')" href="#">Ga_1-xIn_xN_yAs_1-y/GaAs量子阱 LO声子 散射率     

应变量子阱激光器阱宽与组分的确定和增益特性的理论研究

本文根据一维势阱和应变效应的简单理论,给出一种既简单又较准确的确定量子阱的组分和阱宽的方法。并且,针对较为常用的波长为1.3μm的InGaAs/InGaAsP材料以及最新兴起的InAsP/In材料应变量子阱激光器,利用该方法得到了组分和量子阱阱宽。再根据这些参数,利用变分法计算了量子阱的能带结构和二维电子气状态密度。然后,在选取不同的线形函数的情况下分别计算了对应于不同的注入载流予浓度时的这两种激光器的线性增益和微分增益。     

In_(0.2)Ga_(0.8)As/GaAs单量子阱PL谱温度特性及其机制

测量了不同阱宽In0.2Ga0.8As/GaAs单量子阱的PL谱的峰值波长和荧光谱线半峰全宽随温度的变化。利用Varshni公式对实验峰值波长进行拟合,得到了新的参数。结果表明,无位错应变量子阱带隙仍具有其体材料的特性:荧光谱线半峰全宽随温度升高迅速展宽,这主要归因于声子关联作用增强和激子热离化为自由载流子所致;阱宽越窄荧光峰值能量越高,将其与量子尺寸效应的理论计算结果进行了比较。文中还考察了谱线半峰全宽和阱宽的关系,利用合金无序对这一现象进行了解释。     

近800 nm波长张应变GaAsP/AlGaAs量子阱激光器有源区的设计

张应变GaAs_1-xP_x量子阱是高性能大功率半导体激光器的核心有源区,基于能带结构分析优化其结构参数具有重要的应用指导意义.首先,基于6×6 Luttinger-Kohn模型,采用有限差分法计算了张应变GaAs_1-xP_x量子阱的能带结构,得到了第一子带间跃迁波长固定为近800 nm时的阱宽-阱组分关系,即随着阱组分x的增加,需同时增大阱宽,且阱宽较大时靠近价带顶的是轻空穴第一子带lh₁,阱宽较小时靠近价带顶的是重空穴第一子带hh₁.计算并分析了导带第一子带c₁到价带子带lh₁和hh₁的跃迁动量矩阵元.针对808 nm量子阱激光器,模拟计算了阈值增益与阱宽的关系,得到大阱宽有利于横磁模激射,小阱宽有利于横电模激射.进一步考虑了自发辐射和俄歇复合之后,模拟计算了808 nm量子阱激光器的阱宽与阈值电流密度的关系,阱宽较大时载流子对高能级子带的填充使得阈值电流密度增加,而阱宽较小时则是低的有源区光限制因子导致阈值电流密度升高,因此存在一最佳的阱宽-阱组分组合,可使阈值电流密度达到最小.本文的模拟结果可对张应变GaAs_1-xP_x量子阱激光器的理论分析和结构设计提供理论指导.     

In原子掺入对GaInNAs/GaAs单量子阱光致发光的影响

研究了In掺入GaNAs/GaAs单量子阱对其带间和低于带边发光性质的影响。实验结果显示,随着In浓度的增加,GaInNAs/GaAs量子阱带间发光得到改善,低于带边的发光强度大大地减小。这是由于GaInNAs合金生长在GaAs衬底上,为补偿In和N原子尺度的差异,N原子硬倾向于与In原子形成共价健。GaInNAs/GaAs单量子阱的光调制光谱证实了高能端发光峰来自来征的带边发光。     

生长温度和结构参数对InGaAs／GaAs量子阱光学特性的影响

研究了不同生长温度下制备的In0.15Ga0.85As/GaAs应变量子阱的PL谱,结果表明,生长温度越高,In偏析和In-Ga互混越严重,同时,导致更多的In脱附,PL谱发光峰蓝移。对不同In含量的和不同InGaAs厚度的InGaAs/GaAs量子阱进行PL谱测试,分析表明In含量<0.2,生长温度低于560℃时,In含量和InGaAs层量子阱的厚度对In偏析、脱附和In-Ga互混基本没有影响。     

Small-signal modulation characteristics for 1.5 μm lattice-matched InGaNAs/GaAs and InGaAs/InP quantum well lasers

The small-signal modulation characteristics of 1.5 m lattice-matched InGaNAs/GaAs and InGaAs/InP quantum well lasers and their temperature dependence have been calculated. It is found that the maximum bandwidth of the InGaNAs/GaAs quantum well lasers is about 2.3 times larger than that of the InGaAs/InP quantum well lasers due to the high differential gain which results from the large electron effective mass in the dilute nitride system. The slope efficiency for the 3 dB bandwidth as a function of optical density is twice as large for InGaNAs/GaAs as for InGaAs/InP quantum well lasers.     

Reduced linewidth enhancement factor due to excited state transition of quantum dot lasers

The carrier induced refractive index change and linewidth enhancement factor α due to ground-state (GS) and excited-state (ES) transitions have been compared by measuring the optical gain spectra from an InAs/GaAs quantum dot (QD) laser structure. It is shown that the ES transition exhibits a reduced α-factor compared to the value due to the GS transition. This result can be explained by the α-factor due to the ES transition having a smaller increase from the non-resonant carriers in the combined state of the wetting layer and InGaAs strain reducing layer than the α-factor increase due to the GS transition, since the relaxation time for carriers from the combined state of the wetting layer and InGaAs strain reducing layer to the ES is shorter than to the GS. The result reported here shows another advantage of using ES QD lasers for optical communication, in addition to their higher modulation speed.     

Material parameters of InGaAsP and InAlGaAs systems for use in quantum well structures at low and room temperatures

The set of material parameters for quantum well structures is of immense importance because of its usage in the development of theories, extraction of experimental data, and the proper design of devices. In particular, the (Al,In)GaAs/GaAs, InGaAs/InP and (In,Ga)AlAs/InGaAs quantum well systems have drawn a lot of attention. They form the center core of materials used for fundamental basic research and device applications. Despite the presence of some review articles and reference books, there is a lack of clear reference on the accurate determination of the material parameters for quantum wells. This review aims to provide a comprehensive and systematic set of material parameters for the above quantum well systems grown on (1 0 0) substrates at two different temperatures, below 10 K and at around 300 K. The parameters are compared against experimental data from various fabrication sources, measurement techniques, and quantum well structures. The values presented here serve as an accurate and up to date source of reference.     

具有InAlAs浸润层的InGaAs量子点的制备和特性研究

采用自组装方法生长了一种新型的InGaAs量子点/InAlAs浸润层结构.通过选取合适的In组分 ，使InAlAs浸润层的能级与GaAs势垒相当，从而使浸润层的量子阱特征消失.通过低温光致 发光（PL）谱的测试分析得到InGaAs量子点/InAlAs浸润层在样品中的确切位置.变温PL谱的 研究显示，具有这种结构的量子点发光峰的半高全宽随温度上升出现展宽，这明显区别于普 通InGaAs量子点半高全宽变窄的行为.这是因为采用了InAlAs浸润层后，不仅增强了对InGaA s量子点的限制作用，同时切断了载流子的 关键词： InGaAs量子点 InAlAs浸润层 PL谱     

Isolation spectra for InGaAs/GaAs strained single quantum well laser diode optical switches

The spectral dependence of gain and loss for an InGaAs/GaAs strained single quantum well laser diode were measured. High gain and high isolation at the second quantized transition wavelength can be obtained with a low injection current. A strained single quantum well structure is suitable for construction of an integrated optical matrix switch with low power consumption.     

Quantum wire heterostructure for optoelectronic applications

Quantum wire (QWR) heterostructures suitable for optoelectronic applications should meet a number of requirements, including defect free interfaces, large subband separation, long carrier lifetime, efficient carrier capture. The structural and opticl properties of GaAs/AlGaAs and InGaAs/GaAs quantum wire (QWR) heterostructures grown by organometallic chemical vapor deposition on nonplanr substrates, which satisfy many of these criteria, are described. These crescent-shaped QWRs are formed in situ during epitaxial growth resulting in virtually defect free interfaces. Effective wire widths as small as 10nm have been achieved, corresponding to electron subband separations greater than K_BT at room temperature. The enhanced density of states at the QWR subbands manifests itself in higher optical absorption and emission as visualized in photoluminescence (PL), PL excitation, amplified spontaneous emission and lasing spectra of these structures. Effective carrier capture into the wires via connected quantum well regions, which is important for enhancing the otherwise extremely small capture cross section of these wires, has also been observed. Room temperature operation of GaAs/AlGaAs and strained InGaAs/GaAs QWR lasers with threshold currents as low as 0.6mA has been demonstrated.     

Study of the “metal–insulator” transition induced by the impurity fluctuation potential using the Shubnikov–de Haas effect

Heterostructures with a GaAs/InGaAs/GaAs quantum well and aMn magnetic impurity layer separated from it, which have different conductivity types, are studied. At a Mn content not exceeding the amount corresponding to 0.5 monolayer of MnAs, a percolation cluster formed in the quantum well plane is not simply connected, but consists of metal drops separated by low-conductivity interspaces. Despite the absence of the simply connected conducting channel, Shubnikov–de Haas oscillations are observed in all studied systems, which are controlled by carrier properties in conducting drops, independent of Mn content. The estimate of drop sizes corresponds to theoretical values.     

基于p-n结中反常光电转换现象的新型带间跃迁量子阱红外探测器

实验发现p-n结中局域载流子具有极高抽取效率,同时伴随着吸收系数的大幅度增加.本文报道上述现象的发现和验证过程,以及基于此现象的新型带间跃迁量子阱红外探测器(interband transition quantum well infrared detector,IQWIP)原型器件的性能.采用共振激发光致发光光谱技术,在InGaN量子阱、InGaAs量子阱、InAs量子点等多个材料体系中均观察到了在p-n结电场作用下的载流子高效逃逸现象,抽取效率分别为95%,87.5%,88%.利用含有InGaAs/GaAs多量子阱的PIN二极管,实验尝试了制备新型的IQWIP原型器件.在无表面减反射膜的实验条件下,利用仅100 nm的有效吸收厚度,实现了31%的外量子效率.基于这个数值推算得到量子阱的光吸收系数达到3.7×10~4cm~(-1),该数值高于传统透射实验测量体材料和量子阱结果.此外,还利用InAsSb/GaSb量子阱材料体系进行了2μm以上波长红外探测的探索.利用上述现象,有望在提高现有器件性能的同时开发出新颖的光-电转换器件.