+3价离子掺杂钨酸铅晶体发光性能和微观缺陷的研究

通过透射光谱、x射线激发发射光谱（XSL）的测试，研究了Bridgman法生长的几种不同+3价离子掺杂钨酸铅晶体的发光性能，并利用正电子湮没寿命谱（PAT）和x光电子能谱（XPS）的实验手段，对不同钨酸铅晶体的微观缺陷进行研究.实验表明，不同的+3价离子掺杂，对钨酸铅晶体发光性能的改善不同，并使得晶体中正电子俘获中心和低价氧的浓度发生不同变化.其中掺镧晶体的正电子俘获中心和低价氧浓度均上升，而掺钇和掺铋晶体的正电子俘获中心和低价氧浓度均下降，掺锑晶体则出现了正电子俘获中心浓度上升、低价氧浓度下降的情况.提 关键词： 钨酸铅晶体 +3价离子掺杂 正电子湮没寿命谱 x光电子能谱     

掺钇钨酸铅晶体发光性能和微观缺陷的研究

通过透射谱、X射线激发发射谱（XSL）的测试，研究了Bridgman法生长的掺钇钨酸铅晶体的发光性能，并利用正电子湮没寿命谱（PAT）和X光电子能谱（XPS）实验手段，对掺钇钨酸晶体的微观缺陷进行研究。实验表明，钇掺杂能够提高钨酸铅晶体的发光快成分比例，并使得晶体中的正电子俘获中心浓度下降，低价氧浓度下降。提出掺钇钨酸铅晶体中钇的掺杂主要以Y^3 占据VPb的形式存在。Y^3 占据VPb可能是钨酸铅晶体吸收边得到改善的原因，而由于晶体内低价氧浓度的减少，作为绿光发光中心的（WO3＋O^-)基团的减少可能会使发光快成分比例有所增加。     

Nb2O5掺杂对提高钨酸铅晶体发光性能的微观研究

通过透射谱、X射线激发发射谱(XSL)的测试，研究了布里奇曼(Bridgman)法生长的掺铌钨酸铅晶体的发光性能，并利用正电子湮没寿命谱(PAT)和X射线光电子能谱(XPS)的实验手段，对其微观缺陷进行了深入研究。结果表明，铌掺杂能够有效地改善钨酸铅晶体的350nm吸收带，提高钨酸铅晶体的发光快成分比例，并使得晶体中的正电子捕获中心浓度上升，低价氧浓度上升。提出掺铌钨酸铅晶体中Nb^5 将占据W^6 格位并使得晶体内部分(WO4)^2-根团成为(NbO3 Vo)^-，由此可改善钨酸铅的发光性能。     

掺镧PbWO4闪烁晶体的缺陷研究

利用正电子湮没寿命谱(PAT)和X射线电子能谱(XPS)研究了掺镧所引起的PbWO₄ 晶体缺陷的变化.结果表明：掺镧后,PbWO₄晶体中的正电子捕获中心铅空位(V< sub>Pb)浓度增加,并进一步诱导低价氧浓度的增加.讨论了掺La的作用机制,认为掺 La将抑制晶体中的氧空位,增加铅空位浓度. 关键词： 掺镧钨酸铅晶体 正电子湮没寿命谱 X射线电子能谱 缺陷     

Nd掺杂对Bi4Ti3O12铁电薄膜的微结构和铁电性能的影响

利用溶胶-凝胶法在Pt/Ti/SiO₂/Si(100)衬底上制备了Nd掺杂Bi₄Ti₃O₁₂(Bi_4-xNd_xTi₃O₁₂, x=0.00,0.30,0.45,0.75,0.85,1.00,1.50)铁电薄膜样品.研究了Nd掺杂对Bi₄Ti₃O₁₂薄膜的微结构和铁电性能的影响.研究结果表明:Nd掺杂未改变Bi₄Ti₃O₁₂薄膜的基本晶体结构.在掺杂量x<0.45时,Nd³⁺只取代类钙钛矿层中的A位Bi³⁺.当x=0.45时,样品剩余极化强度达最大值,在270kV·cm^-1的电场下为32.7μC·cm^-2.掺杂量进一步增加时,结构无序度开始明显增大,Nd³⁺开始进入(Bi₂O₂)²⁺层,削弱其绝缘层和空间电荷库的作用,导致材料剩余极化逐渐下降.当掺杂量x达到1.50时,掺杂离子最终破坏(Bi₂O₂)²⁺层的结构,材料发生铁电-顺电相变.     

掺铋BaF2晶体的制备及其近红外发光研究

通过温度梯度法制备了Bi₂O₃:BaF₂以及BiF₃:BaF₂晶体.在Bi₂O₃:BaF₂晶体中观察到了发光峰位于961 nm,半高宽202 nm的超宽带红外发光.在BiF₃:BaF₂晶体中检测到Bi²⁺和Bi³⁺可见区的发光,但是没有观察到红外发光.通过γ射线辐照实现了BiF₃:BaF₂晶体的近红外发光, 发光峰位于1135 nm,半高宽192 nm.讨论了Bi₂O₃和BiF₃掺杂BaF₂晶体的红外发光的机理.     

掺Bi离子锗铌酸盐红外发光玻璃的研究

用高温熔融法制备了Bi₂O₃掺杂的(0.9-x) GeO₂-xNb₂O₅-0.1BaO (含量x为摩尔分数, x=0, 0.04, 0.07, 0.1)系列玻璃. 测定了玻璃样品的差热分析(DTA)曲线、吸收光谱、发射光谱及X射线光电子能谱(XPS). 从DTA曲线分析得到玻璃的结晶起始温度与软化温度之差(T_x-T_g)达200℃以上. 吸收光谱中可观察到位于500, 700, 808和1000 nm处的吸收峰, 并随着Nb₂O₅含量x的增加吸收边带发生红移. 在波长为808 nm激光激发下, 观察到发光中心位于1300 nm处、荧光光谱半高宽约为200 nm的宽带发光. 荧光强度随Bi₂O₃掺杂量δ的增加先增强后减弱, 当掺杂量δ达到约0.01时, 荧光强度达到最强. 随着Nb₂O₅含量x从0.04增加到0.1时, 荧光强度逐步减弱. 样品的XPS峰分别位于159.6和164.7 eV, 它们介于Bi³⁺与Bi⁵⁺的特征结合能之间, 因此Bi³⁺与Bi⁵⁺可能同时存在于玻璃基质中. 从XPS及Bi离子的发光特性推断, 宽带的荧光发射可能起因于Bi⁵⁺. 随着Nb₂O₅含量x的增加, 荧光强度逐步减弱. 分析认为, Nb₂O₅取代GeO₂后形成了NbGe缺陷, 需要低价Bi离子进行电子补偿, 因而抑制了Bi⁵⁺形成, 致使荧光强度减弱.     

PbWO4闪烁晶体的辐照损伤机理研究

完成了640—1040℃温度范围内钨酸铅［PbWO₄(PWO)］晶体的退火实验,观察到较低温退火时晶体中本征色心吸收带(350nm)先是增加,其后随退火温度的升高而逐渐降低直至消除的全过程．分析了PWO晶体的本征缺陷和电荷补偿机制．讨论了退火过程中氧进入晶体后色心的产生和转化规律,并提出可能发生Pb³⁺→Pb⁴⁺的进一步氧化过程,从而导致Pb³⁺空穴中心的湮没．测量并比较了不同退火温度处理后PWO晶体的紫外辐照诱导色心     

掺镧PbWO4闪烁晶体的缺陷研究

利用正电子湮没寿命谱(PAT)和X射线电子能谱(XPS)研究了掺镧所引起的PbWO4晶体缺陷的变化.结果表明:掺镧后,PbWO4晶体中的正电子捕获中心铅空位(VPb)浓度增加,并进一步诱导低价氧浓度的增加.讨论了掺La的作用机制,认为掺La将抑制晶体中的氧空位,增加铅空位浓度.     

Bi2WO6光催化剂的γ射线辐射效应

本文首次研究了高能辐射(γ射线)对Bi₂WO₆纳米晶体结构和光催化性能的影响. 结果表明,尽管高能辐射不会改变Bi₂WO₆纳米晶体的形貌,但是Bi₂WO₆粉末的颜色在高吸收剂量辐照(507 kGy)后发生了明显的变化,并且辐照后Bi₂WO₆的XRD谱图也显示,随着吸收剂量的增加,(113)晶面对应的2θ从28.37°移到28.45°,说明晶格参数在γ射线辐照下还是发生了细微的变化. XPS表征结果证明,Bi₂WO₆晶体结构的变化源于高剂量辐射下氧空位缺陷的产生. Bi₂WO₆纳米晶体的禁带宽度(E_g)随吸收剂量的增加也出现减小的趋势. 用水溶液中亚甲基蓝的可见光照分解反应作为模型反应考察了辐照后的Bi₂WO₆纳米晶体的光催化活性,结果表明,辐照后的Bi₂WO₆纳米晶体的光催化活性随着吸收剂量的增加而逐渐升高. 将经过反应后的Bi₂WO₆纳米晶体再次回收,进行循环催化,发现这些辐照后的Bi₂WO₆纳米晶体在三次循环使用后光催化性能仍然能够保持,说明高能辐射产生的氧空位缺陷具有良好的稳定性.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.