The effect of annealing on the room temperature ferromagnetism in co-sputtered In2O3: C thin films

In this paper, we report investigation of room temperature (RT) ferromagnetism in In₂O₃ (InO) thin films doped with carbon prepared by the co-sputtering method. InO thin films both undoped and C doped with varied thicknesses in the range of 45 to 80 nm were synthesized on Si substrates with varied C concentrations. The carbon concentration was varied from 1.6 to 9.3 at%. The undoped InO films showed no trace of ferromagnetism. Carbon doped films (InO:C) exhibited ferromagnetism at RT, which was of the orders of 10⁻⁵ emu and varied strongly with C concentrations. It is observed that the magnetization reached a maximum value of 5.7 emu/cm³ at 4 at% C. Annealing of the InO:C films in an oxygen environment resulted in a decrease in the magnetization, indicating the crucial role of oxygen vacancies in the films. It is concluded that the oxygen vacancies were important and compete with C substitution for the RT ferromagnetism.     

Magnetism due to oxygen vacancies and/or defects in undoped semiconducting and insulating oxide thin films

Room temperature ferromagnetism was observed in HfO₂, TiO₂, and In₂O₃ films grown on yttrium-stabilized zirconia, LaAlO₃, and MgO substrates, respectively. While the magnetic moment is rather modest in the case of In₂O₃ films, it is very large in the other two cases. Thin film form, which might create necessary defects and/or oxygen vacancies, must be the main reason for undoped semiconducting and insulating oxides to become ferromagnetic. From the results, a serious question arises if a transition-metal doping indeed plays any essential role in producing ferromagnetism (FM) in non-magnetic oxides.     

A close correlation between induced ferromagnetism and oxygen deficiency in Fe doped In2O3

We report on the reversible manipulation of room temperature ferromagnetism in Fe (5%) doped In₂O₃ polycrystalline magnetic semiconductor. The X-ray diffraction and photoemission measurements confirm that the Fe ions are well incorporated into the lattice, substituting the In³⁺ ions. The magnetization measurements show that the host In₂O₃ has a diamagnetic ground state, while it shows weak ferromagnetism at 300 K upon Fe doping. The as-prepared sample was then sequentially annealed in hydrogen, air, vacuum and finally in air. The ferromagnetic signal shoots up by hydrogenation as well as vacuum annealing and bounces back upon re-annealing the samples in air. The sequence of ferromagnetism shows a close inter-relationship with the behavior of oxygen vacancies (V_o). The Fe ions tend to a transform from 3+ to 2+ state during the giant ferromagnetic induction, as revealed by photoemission spectroscopy. A careful characterization of the structure, purity, magnetic, and transport properties confirms that the ferromagnetism is due to neither impurities nor clusters but directly related to the oxygen vacancies. The ferromagnetism can be reversibly controlled by these vacancies while a parallel variation of carrier concentration, as revealed by resistance measurements, appears to be a side effect of the oxygen vacancy variation.     

Co-doped In2O3 thin films: Room temperature ferromagnets

Laser-ablated Co-doped In₂O₃ thin films were fabricated under various growth conditions on R-cut Al₂O₃ and MgO substrates. All Co:In₂O₃ films are well-crystallized, single phase, and room temperature ferromagnetic. Co atoms were well substituted for In atoms, and their distribution is greatly uniform over the whole thickness of the films. Films grown at 550 °C showed the largest magnetic moment of about 0.5 μ_B/Co, while films grown at higher temperatures have magnetic moments of one order smaller. The observed ferromagnetism above room temperature in Co:In₂O₃ thin films has confirmed that doping few percent of magnetic elements such as Co into In₂O₃ could result in a promising magnetic material.     

Synthesis of monodisperse In2O3 nanoparticles and their d0 ferromagnetism

Monodisperse indium oxide (In₂O₃) nanoparticles (NPs) with the average diameter of 11 nm were prepared by a solvothermal method. The In₂O₃ NPs were characterized by X-ray diffraction, Raman and transmission electron microscopy. The intrinsic nature of ferromagnetism in In₂O₃ NPs has been established with the experimental observation of magnetic hysteresis loop. Photoluminescence and UV–visible studies were employed to evidence the presence of oxygen vacancies and revealed that the oxygen vacancies contribute to the ferromagnetism. The origin of ferromagnetism in In₂O₃ NPs may be due to exchange interactions among localized electron spin moments resulting from oxygen vacancies.     

Ferromagnetism induced by oxygen-vacancy complex in (Mn,in) codoped ZnO

Mn doped Zinc oxide (ZnO) thin films were prepared by metal organic chemical vapor deposition (MOCVD) technique. Structural characterizations by X-ray diffraction technique (XRD) and photoluminescence (PL) indicate the crystal quality of ZnO films. PL and Raman show a large fraction of oxygen vacancies (V_O²⁺) are generated by vacuum annealed the film. The enhancement of ferromagnetism in post-annealed (Mn, In) codoped ZnO could result from V_O²⁺ incorporation. The effect of V_O²⁺ on the magnetic properties of (Mn, In) codoped ZnO has been studied by first-principles calculations. It is found that only In donor cannot induce ferromagnetism (FM) in Mn-doped ZnO. Besides, the presence of V_O²⁺ makes the Mn empty 3d-t_2g minority state broadened, and a t_2g-V_O²⁺ hybrid level at the conduction band minimum forms. The presence of V_O²⁺ can lead to strong ferromagnetic coupling with the nearest neighboring Mn cation by BMP model based on defects reveal that the ferromagnetic exchange is mediated by the donor impurity state, which mainly consists of Mn 3d electrons trapped in oxygen vacancies.     

Effect of hydrogenation vs. re-heating on intrinsic magnetization of Co doped In2O3

Influence of Co doping for In in In₂O₃ matrix has been investigated to study the effect on magnetic vs. electronic properties. Rietveld refinement of X-ray diffraction patterns confirmed formation of single phase cubic bixbyite structure without any parasitic phase. Photoelectron spectroscopy and refinement results further revealed that dopant Co²⁺ ions are well incorporated at the In³⁺ sites in In₂O₃ lattice and also ruled out formation of cluster in the doped samples. Magnetization measurements infer that pure In₂O₃ is diamagnetic and turns to weak ferromagnetic upon Co doping. Hydrogenation further induces a huge ferromagnetism at 300 K that vanishes upon re-heating. Experimental findings confirm the induced ferromagnetism to be intrinsic, and the magnetic moments to be associated with the point defects (oxygen vacancies V_o) or bound magnetic polarons around the dopant ions.     

The coexistence of ferroelectricity and ferromagnetism in Mn-doped BaTiO3 thin films

Due to the fault of the first author, this article entitled “The coexistence of ferroelectricity and ferromagnetism in Mn-doped BaTiO3 thin films”, published in “Chinese Physics B”, 2011,Vol.20, Issue 12, Article No. 127701, has been found to copy from the article entitled“Decisive role of oxygen vacancy in ferroelectric versus ferromagnetic Mn-doped BaTiO3 thin films”, published in “Journal of Applied Physics”, 2011,Vol.109, Issue 8, article No. 084105. So the above article in “Chinese Physics B” has been withdrawn from the publication.<     

Control of ferromagnetism in Fe-doped In2O3 by carbothermal annealing

Fe-doped In₂O₃ powders were prepared using the sol–gel method. Solubility of Fe ions in the In₂O₃ host compound reached up to 50%. Lattice constant decreased linearly as Fe doping concentration increased, indicating that Fe ions were incorporated into the host lattice and occupied the In sites. Ferromagnetism could be obtained from the samples with carbothermal annealing. The dependence of ferromagnetism on the carbon dosage was observed. The greater the carbon dosage, the higher the concentration of oxygen vacancies (V_o) created, and the more robust the ferromagnetism.     

The investigation of room temperature ferromagnetism in (1 0 0) oriented BaNb2O6 PLD films on LaAlO3 (1 0 0) substrate

(1 0 0) oriented BaNb₂O₆ films have been successfully grown on LaAlO₃ (1 0 0) substrate at 750 °C or 450 °C in vacuum by pulsed laser deposition. The deposited BaNb₂O₆ PLD films exhibit room-temperature ferromagnetism. Ab initio calculations demonstrate that stoichiometric BaNb₂O₆ and that with barium vacancy are nonmagnetic, while oxygen and niobium vacancy can induce magnetism due to the spin-polarization of Nb s electrons and O p electrons respectively. Moreover, ferromagnetic coupling is energetically more favorable when two Nb/O vacancies are located third-nearest-neighbored. The observed room temperature ferromagnetism in BaNb₂O₆ films should be mainly induced by oxygen vacancies introduced during vacuum deposition, with certain contribution by Nb vacancies.     

Ferromagnetism in transition-metal-doped semiconducting oxide thin films

A rather complete work on transition-metal (TM)-doped TiO₂ thin films has been done and room ferromagnetism (FM) is found in the whole series of Sc/V/Cr/Mn/Fe/Co/Ni-doped TiO₂ films. Not only is it remarkable that for the first time, FM at high temperature was achieved in TM-doped TiO₂, but also a very big magnetic moment of 4.2μ_B/atom could be obtained, and direct evidences of real ferromagnets with big domains were shown as well. A similar chemical trend was achieved in TM-doped In₂O₃ films, however, the observed magnetic moment is rather modest, with the maximal value is of only 0.7μ_B/atom for Ni-doped In₂O₃ films. As regards TM-doped SnO₂ films, observed magnetic moments could be very large, with the maximum saturation of 6μ_B per impurity atom for Cr-doped SnO₂ thin films, but it could be influenced very much depending on substrate types. On the other hand, results on TM-doped ZnO films interestingly have revealed that in these systems, the magnetism more likely resulted from defects and/or oxygen vacancies.     

Structural, electrical, and optical properties of ZnInO alloy thin films

Indium zinc oxide (IZO) thin films with different percentages of In content (In/[In+Zn]) are synthesized on glass substrates by magnetron sputtering, and the structural, electrical and optical properties of IZO thin films deposited at different In₂O₃ target powers are investigated. IZO thin films grown at different In₂O₃ target sputtering powers show evident morphological variation and different grain sizes. As the In₂O₃ sputtering power rises, the grain size becomes larger and electrical mobility increases. The film grown with an In₂O₃ target power of 100 W displays the highest electrical mobility of 13.5 cm·V^-1·s^-1 and the lowest resistivity of 2.4 × 10^-3 Ω·cm. The average optical transmittance of the IZO thin film in the visible region reaches 80% and the band gap broadens with the increase of In₂O₃ target power, which is attributed to the increase in carrier concentration and is in accordance with Burstein-Moss shift theory.     

Mn和N共掺ZnO稀磁半导体薄膜的研究

使用对Zn₂N₃:Mn薄膜热氧化的方法成功制备了高含N量的Mn和N共掺ZnO的稀磁半导体薄膜.在没有N离子共掺的情况下,ZnO:Mn薄膜的铁磁性非常微弱;如果进行N离子的共掺杂,就会发现ZnO:Mn薄膜在室温下表现出非常明显的铁磁性,饱和离子磁矩为0.23 μ_B—0.61 μ_B.这说明N的共掺激发了ZnO:Mn薄膜中的室温铁磁性,也就是受主的共掺引起的空穴有利于ZnO中二价Mn离子的铁磁性耦合,这和最近的相关理论研究符合很好. 关键词： 磁性半导体 受主掺杂 空穴媒介的铁磁性     

Anomalous Hall effect in Cu and Fe codoped In2O3 and ITO thin films

We present a systematic study of the structure, magnetization, resistivity, and Hall effect properties of pulsed laser deposited Fe- and Cu-codoped In₂O₃ and indium-tin-oxide (ITO) thin films. Both the films show a clear ferromagnetism and anomalous Hall effect at 300 K. The saturated magnetic moments are almost the same for the two samples, but their remanent moments M_r and coercive fields H_C are quite different. M_r and H_C values of ITO film are much smaller than that of In₂O₃. The ITO sample shows a typical semiconducting behavior in whole studied temperature range, while the In₂O₃ thin film is metallic in the temperature range between 147 and 285 K. Analysis of different conduction mechanisms suggest that charge carriers are not localized in the present films. The profile of the anomalous Hall effect vs. magnetic field was found to be identical to the magnetic hysteresis loops, indicating the possible intrinsic nature of ferromagnetism in the present samples.     

Effects of annealing conditions on the electrical properties of Bi4-xNdxTi3O12 (x = 0.46) thin films processed at low temperature

Neodymium-substituted Bi₄Ti₃O₁₂ (BNdT) thin films were prepared by a chemical solution deposition technique on platinum- coated silicon substrates. All of the samples were annealed at the relatively low temperature of 600 °C by a rapid thermal annealing process in different atmospheres, such as O₂, air, and nitrogen, and vacuum. Irrespective of different annealing atmospheres, all of the BNdT thin films exhibit good ferroelectric properties, such as a saturated hysteresis loop, good fatigue endurance, and low leakage current density. A large remanent polarization (P_r) of ∼48 μC/cm² with an electric field of 240 kV/cm was observed from the BNdT thin film annealed in O₂ atmosphere. The BNdT thin films annealed in nitrogen and vacuum, at reduced oxygen partial pressures, exhibit smaller P_r than that annealed in oxygen. The difference of P_r of the BNdT thin films annealed in different atmospheres may originate from differences in the grain sizes and the number of oxygen vacancies. PACS 77.55.+f; 77.80.-e; 77.80.Fm; 81.15.-z     

High temperature ferromagnetism in cubic Mn-doped ZrO2 thin films

Theory has predicted that high temperature ferromagnetism (FM) should be found in cubic fake-diamonds, Mn-doped ZrO₂. Experimentally, it is shown that Mn-doped ZrO₂ ceramics are not ferromagnetic, but the nanosized Mn-doped ZrO₂ thin films grown on LaAlO₃ substrates can be ferromagnets with T_C above 400 K. The largest saturated magnetic moment (M_s) is huge as of about 230 emu/cm³ for the Mn_0.05Zr_0.95O₂ films, and it decreases as the Mn content increases. The intrinsic FM is strongly associated with the cubic structure of Mn-doped ZrO₂, and the Mn–Mn interactions via oxygen intermediates are important. No electrical conductivity is observed. Mn-doped ZrO₂ thin films can be truly considered as excellent candidates for spintronic applications.     

Effect of indium incorporation in Zn1−xCoxO thin films

In the present paper, the preliminary investigations of a series of ZnO thin films co-doped with indium and cobalt with an objective to elucidate the correlation, if any, between the carrier concentration and the induced room temperature ferromagnetism (RTFM), are presented. The single-phasic (Zn_99.5In_0.5)_1−xCo_xO thin films are deposited by spray pyrolysis. The substitution of Zn²⁺ by Co²⁺ has been established by optical transmission analysis of these films. The films are ferromagnetic at room temperature; and the magnetization has higher value for indium and cobalt co-doped thin film as compared with Zn0₉₀Co_0.1O thin film (having no indium).     

Room temperature ferromagnetic pure ZnO

Pure ZnO films were prepared by pulsed laser deposition on oxidized Si substrates under different oxygen pressure and substrate temperature. Clear room temperature ferromagnetism has been observed in the ZnO film prepared under high vacuum and room temperature. The observation of anomalous Hall effect confirms the intrinsic nature of the ferromagnetism. The photoluminescence and X-ray photoelectron spectroscopy spectra show the high concentration of oxygen vacancies in the ferromagnetic ZnO film. Our results clearly demonstrate the ferromagnetic contribution of the oxygen vacancies mediated by the spin polarized electrons hopping between discrete states in pure ZnO.     

Effect of W co-doping on the optical,magnetic and electrical properties of Fe-doped BaSnO3

The effect of W co-doping on the optical, magnetic and electrical properties of Fe-doped BaSnO₃ has been studied. Polycrystalline BaSnO₃, BaSn_0.96Fe_0.04O₃ and BaSn_0.95Fe_0.04W_0.01O₃ samples were prepared using solid state reaction. In the analysis of powder X-ray diffraction patterns, the samples were found to be free of secondary phases. Diffuse reflectance spectra evidenced the substitution of Fe and W for Sn in the host BaSnO₃. Micro-Raman spectra confirmed the existence of oxygen vacancies in the samples. Upon W-1% co-doping, the ferromagnetic character of Fe-4% doped BaSnO₃ is suppressed drastically and its Curie temperature is reduced to 310 K from 462 K. The existence of F-centers and ferromagnetic interactions at room temperature is evidenced by the electron paramagnetic resonance and ferromagnetic resonance signals observed in the electron spin resonance spectra of the undoped and Fe-4% doped, (Fe-4% and W-1%) co-doped BaSnO₃ samples respectively. Suppression of ferromagnetism upon W co-doping is due to the fact that each W⁶⁺ ion donates two electrons to the host lattice and it reduces the number of oxygen vacancies that are essential for ferromagnetism to exist in the Fe-doped BaSnO₃ samples.