Ferromagnetism in carbon-doped In2O3 thin films

Carbon-doped In₂O₃ thin films exhibiting ferromagnetism at room temperature were prepared on Si (100) substrates by the rf-magnetron co-sputtering technique. The effects of carbon concentration as well as oxygen atmosphere on the ferromagnetic property of the thin films were investigated. The saturated magnetizations of thin films varied from 1.23 to 4.86 emu/cm³ with different carbon concentrations. The ferromagnetic signal was found stronger in samples with higher oxygen vacancy concentrations. In addition, deposition temperature and different types of substrates also affect the ferromagnetic properties of carbon-doped In₂O₃ thin films. This may be related to the oxygen vacancies in the thin film system. The experiment suggests that oxygen vacancies play an important role in introducing ferromagnetism in thin films.     

A close correlation between induced ferromagnetism and oxygen deficiency in Fe doped In2O3

We report on the reversible manipulation of room temperature ferromagnetism in Fe (5%) doped In₂O₃ polycrystalline magnetic semiconductor. The X-ray diffraction and photoemission measurements confirm that the Fe ions are well incorporated into the lattice, substituting the In³⁺ ions. The magnetization measurements show that the host In₂O₃ has a diamagnetic ground state, while it shows weak ferromagnetism at 300 K upon Fe doping. The as-prepared sample was then sequentially annealed in hydrogen, air, vacuum and finally in air. The ferromagnetic signal shoots up by hydrogenation as well as vacuum annealing and bounces back upon re-annealing the samples in air. The sequence of ferromagnetism shows a close inter-relationship with the behavior of oxygen vacancies (V_o). The Fe ions tend to a transform from 3+ to 2+ state during the giant ferromagnetic induction, as revealed by photoemission spectroscopy. A careful characterization of the structure, purity, magnetic, and transport properties confirms that the ferromagnetism is due to neither impurities nor clusters but directly related to the oxygen vacancies. The ferromagnetism can be reversibly controlled by these vacancies while a parallel variation of carrier concentration, as revealed by resistance measurements, appears to be a side effect of the oxygen vacancy variation.     

Control of ferromagnetism in Fe-doped In2O3 by carbothermal annealing

Fe-doped In₂O₃ powders were prepared using the sol–gel method. Solubility of Fe ions in the In₂O₃ host compound reached up to 50%. Lattice constant decreased linearly as Fe doping concentration increased, indicating that Fe ions were incorporated into the host lattice and occupied the In sites. Ferromagnetism could be obtained from the samples with carbothermal annealing. The dependence of ferromagnetism on the carbon dosage was observed. The greater the carbon dosage, the higher the concentration of oxygen vacancies (V_o) created, and the more robust the ferromagnetism.     

Magnetism due to oxygen vacancies and/or defects in undoped semiconducting and insulating oxide thin films

Room temperature ferromagnetism was observed in HfO₂, TiO₂, and In₂O₃ films grown on yttrium-stabilized zirconia, LaAlO₃, and MgO substrates, respectively. While the magnetic moment is rather modest in the case of In₂O₃ films, it is very large in the other two cases. Thin film form, which might create necessary defects and/or oxygen vacancies, must be the main reason for undoped semiconducting and insulating oxides to become ferromagnetic. From the results, a serious question arises if a transition-metal doping indeed plays any essential role in producing ferromagnetism (FM) in non-magnetic oxides.     

Effect of hydrogenation vs. re-heating on intrinsic magnetization of Co doped In2O3

Influence of Co doping for In in In₂O₃ matrix has been investigated to study the effect on magnetic vs. electronic properties. Rietveld refinement of X-ray diffraction patterns confirmed formation of single phase cubic bixbyite structure without any parasitic phase. Photoelectron spectroscopy and refinement results further revealed that dopant Co²⁺ ions are well incorporated at the In³⁺ sites in In₂O₃ lattice and also ruled out formation of cluster in the doped samples. Magnetization measurements infer that pure In₂O₃ is diamagnetic and turns to weak ferromagnetic upon Co doping. Hydrogenation further induces a huge ferromagnetism at 300 K that vanishes upon re-heating. Experimental findings confirm the induced ferromagnetism to be intrinsic, and the magnetic moments to be associated with the point defects (oxygen vacancies V_o) or bound magnetic polarons around the dopant ions.     

The effect of annealing on the room temperature ferromagnetism in co-sputtered In2O3: C thin films

In this paper, we report investigation of room temperature (RT) ferromagnetism in In₂O₃ (InO) thin films doped with carbon prepared by the co-sputtering method. InO thin films both undoped and C doped with varied thicknesses in the range of 45 to 80 nm were synthesized on Si substrates with varied C concentrations. The carbon concentration was varied from 1.6 to 9.3 at%. The undoped InO films showed no trace of ferromagnetism. Carbon doped films (InO:C) exhibited ferromagnetism at RT, which was of the orders of 10⁻⁵ emu and varied strongly with C concentrations. It is observed that the magnetization reached a maximum value of 5.7 emu/cm³ at 4 at% C. Annealing of the InO:C films in an oxygen environment resulted in a decrease in the magnetization, indicating the crucial role of oxygen vacancies in the films. It is concluded that the oxygen vacancies were important and compete with C substitution for the RT ferromagnetism.     

Observation of room temperature ferromagnetism in pure La2O3 nanoparticles

In this paper, we report the observation of intrinsic room temperature ferromagnetism in pure La₂O₃ nanoparticles. Magnetism measurement indicates that all of the samples exhibit room temperature ferromagnetism and the saturation magnetization for the samples decreases with the increase in annealing temperature from 700 to 1,000 °C. X-ray photoelectron spectroscopy identifies the presence of oxygen vacancies in the La₂O₃ nanoparticles. The fitting results of the O 1s spectrum indicate that the variation of the oxygen vacancy concentration is in complete agreement with the change of the saturation magnetization. It is also found that the saturation magnetization of the La₂O₃ nanoparticles can be tuned by post-annealing in argon or oxygen atmosphere. These results suggest that the oxygen vacancies are largely responsible for the room temperature ferromagnetism in pure La₂O₃ nanoparticles.     

Fabrication and photoluminescence characteristics of In2O3 nanohillocks

Uniformly distributed polycrystalline indium nanohillocks are synthesized on silicon substrates with Au catalyst by using the radio frequency magnetic sputtering technique. The results show that the Au catalyst plays a key role in the formation of indium nanohillocks. After thermally oxidizing the indium nanohillocks at 500 ℃ in air for 5 h, the indium nanohillocks totally transform into In₂O₃ nanohillocks. The energy-dispersive X-ray spectroscopy result indicates that many oxygen vacancies and oxygen-indium vacancy pairs exist in the In₂O₃ nanohillocks. Photoluminescence spectra under an Ne laser excitation at 280 nm show broad emissions at 420 nm and 470 nm with a shoulder at 450 nm related to oxygen vacancies and oxygen-indium vacancies at room temperature.     

The investigation of room temperature ferromagnetism in (1 0 0) oriented BaNb2O6 PLD films on LaAlO3 (1 0 0) substrate

(1 0 0) oriented BaNb₂O₆ films have been successfully grown on LaAlO₃ (1 0 0) substrate at 750 °C or 450 °C in vacuum by pulsed laser deposition. The deposited BaNb₂O₆ PLD films exhibit room-temperature ferromagnetism. Ab initio calculations demonstrate that stoichiometric BaNb₂O₆ and that with barium vacancy are nonmagnetic, while oxygen and niobium vacancy can induce magnetism due to the spin-polarization of Nb s electrons and O p electrons respectively. Moreover, ferromagnetic coupling is energetically more favorable when two Nb/O vacancies are located third-nearest-neighbored. The observed room temperature ferromagnetism in BaNb₂O₆ films should be mainly induced by oxygen vacancies introduced during vacuum deposition, with certain contribution by Nb vacancies.     

Synthesis of In-doped Ga2O3 zigzag-shaped nanowires and optical properties

In-doped Ga₂O₃ zigzag-shaped nanowires and undoped Ga₂O₃ nanowires have been synthesized on Si substrate by thermal evaporation of mixed powders of Ga, In₂O₃ and graphite at 1000 °C without using any catalyst via a vapor-solid growth mechanism. The morphologies and microstructures of the products were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and photoluminescence spectroscopy (PL). The nanowires range from 100 nm to several hundreds of nanometers in diameter and several tens of micrometers in length. A broad emission band from 400 to 700 nm is obtained in the PL spectrum of these nanowires at room temperature. There are two blue-emission peaks centering at 450 and 500 nm, which originate from the oxygen vacancies, gallium vacancies and gallium-oxygen vacancy pairs.     

Electrical and optical spectroscopy on ZnO:Co thin films

Magnetic oxide semiconductors, for example the highly transparent and intrinsically n-type conducting zinc oxide doped with the 3d transition metal Co (ZnO:Co), are promising for the emerging field of spintronics [1]. We investigated n-conducting ZnO:Co thin films with a Co content of nominal 0.02, 0.20, or 2.00 at. %. The substitution of Co cations in the tetrahedral sites of wurtzite ZnO with Zn was confirmed at low temperature by the 1.877 eV photoluminescence between crystal field split d-levels of Co²⁺ (d⁷) ions. Based on theoretical studies, it is predicted that the formation of electron levels with zinc interstitials (I_Zn) or hole levels with zinc vacancies (V_Zn) is necessary to induce ferromagnetism, whereas the formation of electron levels with oxygen vacancies (V_O) is detrimental for ferromagnetism in ZnO:Co [2]. Cobalt generates a hole level in ZnO [3]. We investigated the generation of electron levels in n-conducting ZnO:Co in dependence on the Co content by means of deep level transient spectroscopy (DLTS). However, because of the ambiguous categorization of deep defects in n-conducting ZnO (V_O, I_Zn), an optimization of defect-related ferromagnetism in ZnO:Co is not possible at the moment. PACS 78.30.Fs; 91.60.Ed; 91.60.Mk     

Ferromagnetism induced by oxygen-vacancy complex in (Mn,in) codoped ZnO

Mn doped Zinc oxide (ZnO) thin films were prepared by metal organic chemical vapor deposition (MOCVD) technique. Structural characterizations by X-ray diffraction technique (XRD) and photoluminescence (PL) indicate the crystal quality of ZnO films. PL and Raman show a large fraction of oxygen vacancies (V_O²⁺) are generated by vacuum annealed the film. The enhancement of ferromagnetism in post-annealed (Mn, In) codoped ZnO could result from V_O²⁺ incorporation. The effect of V_O²⁺ on the magnetic properties of (Mn, In) codoped ZnO has been studied by first-principles calculations. It is found that only In donor cannot induce ferromagnetism (FM) in Mn-doped ZnO. Besides, the presence of V_O²⁺ makes the Mn empty 3d-t_2g minority state broadened, and a t_2g-V_O²⁺ hybrid level at the conduction band minimum forms. The presence of V_O²⁺ can lead to strong ferromagnetic coupling with the nearest neighboring Mn cation by BMP model based on defects reveal that the ferromagnetic exchange is mediated by the donor impurity state, which mainly consists of Mn 3d electrons trapped in oxygen vacancies.     

Effect of W co-doping on the optical,magnetic and electrical properties of Fe-doped BaSnO3

The effect of W co-doping on the optical, magnetic and electrical properties of Fe-doped BaSnO₃ has been studied. Polycrystalline BaSnO₃, BaSn_0.96Fe_0.04O₃ and BaSn_0.95Fe_0.04W_0.01O₃ samples were prepared using solid state reaction. In the analysis of powder X-ray diffraction patterns, the samples were found to be free of secondary phases. Diffuse reflectance spectra evidenced the substitution of Fe and W for Sn in the host BaSnO₃. Micro-Raman spectra confirmed the existence of oxygen vacancies in the samples. Upon W-1% co-doping, the ferromagnetic character of Fe-4% doped BaSnO₃ is suppressed drastically and its Curie temperature is reduced to 310 K from 462 K. The existence of F-centers and ferromagnetic interactions at room temperature is evidenced by the electron paramagnetic resonance and ferromagnetic resonance signals observed in the electron spin resonance spectra of the undoped and Fe-4% doped, (Fe-4% and W-1%) co-doped BaSnO₃ samples respectively. Suppression of ferromagnetism upon W co-doping is due to the fact that each W⁶⁺ ion donates two electrons to the host lattice and it reduces the number of oxygen vacancies that are essential for ferromagnetism to exist in the Fe-doped BaSnO₃ samples.     

Intrinsic magnetic properties of In2O3 and transition metal-doped-In2O3

This paper reports on the influence of the sintering temperature and atmosphere and transition-metal doping on the magnetic properties of nanocrystalline and bulk In₂O₃. Undoped nanocrystalline In₂O₃ is diamagnetic whatever the sintering temperature and atmosphere. All single-phase transition-metal-doped In₂O₃ samples are paramagnetic, with a paramagnetic effective moment originating from weakly interacting transition metal ions. No trace of ferromagnetism has been detected even with samples sintered under argon, except extrinsic ferromagnetism for samples with magnetic dopant concentrations exceeding the solubility limit.     

Ferromagnetism in transition-metal-doped semiconducting oxide thin films

A rather complete work on transition-metal (TM)-doped TiO₂ thin films has been done and room ferromagnetism (FM) is found in the whole series of Sc/V/Cr/Mn/Fe/Co/Ni-doped TiO₂ films. Not only is it remarkable that for the first time, FM at high temperature was achieved in TM-doped TiO₂, but also a very big magnetic moment of 4.2μ_B/atom could be obtained, and direct evidences of real ferromagnets with big domains were shown as well. A similar chemical trend was achieved in TM-doped In₂O₃ films, however, the observed magnetic moment is rather modest, with the maximal value is of only 0.7μ_B/atom for Ni-doped In₂O₃ films. As regards TM-doped SnO₂ films, observed magnetic moments could be very large, with the maximum saturation of 6μ_B per impurity atom for Cr-doped SnO₂ thin films, but it could be influenced very much depending on substrate types. On the other hand, results on TM-doped ZnO films interestingly have revealed that in these systems, the magnetism more likely resulted from defects and/or oxygen vacancies.     

Rapid oxidation of InP nanoparticles in air

InP nanoparticles (NPs) in the size range of 1.5-3 nm were synthesized using colloidal chemistry methods. Exposure of these NPs to air resulted in rapid oxidation, as shown by transmission electron microscopy. Diffraction and spectroscopic measurements confirmed the formation of In₂O₃. Similar behavior was observed for commercial InP NPs, even when capped with a ZnS shell. Photoluminescence studies suggest that the oxidation occurs even while InP NPs are still dispersed in hexane, albeit at a much slower rate.     

High temperature ferromagnetism of the vacuum-annealed (In1−xFex)2O3 powders

(In_1−xFe_x)₂O₃ (x = 0.02, 0.05, 0.2) powders were prepared by a solid state reaction method and a vacuum annealing process. A systematic study was done on the structural and magnetic properties of (In_1−xFe_x)₂O₃ powders as a function of Fe concentration and annealing temperature. The X-ray diffraction and high-resolution transmission electron microscopy results confirmed that there were not any Fe or Fe oxide secondary phases in vacuum-annealed (In_1−xFe_x)₂O₃ samples and the Fe element was incorporated into the indium oxide lattice by substituting the position of indium atoms. The X-ray photoelectron spectroscopy revealed that both Fe²⁺ and Fe³⁺ ions existed in the samples. Magnetic measurements indicated that all samples were ferromagnetic with the magnetic moment of 0.49-1.73 μ_B/Fe and the Curie temperature around 783 K. The appearance of ferromagnetism was attributed to the ferromagnetic coupling of Fe²⁺ and Fe³⁺ ions via an electron trapped in a bridging oxygen vacancy.     

Control synthesis of octahedral In2O3 crystals,belts, and nanowires

Octahedral In₂O₃ crystals were synthesized by evaporation of a mixture of In₂O₃ and graphite in a horizontal double-tube system. By adjusting the experimental conditions, In₂O₃ nanowires and nanobelts were also obtained. The microstructures of the resultant In₂O₃ materials were characterized by scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), selected-area electron diffraction (SAED), X-ray diffraction. In addition, the growth mechanism of the octahedral In₂O₃ crystals was discussed in detail.     

Highly transparent Ag doped In2O3 electrodes with high work function for organic solar cells

We report highly transparent Ag-doped In₂O₃ (IAO) films with high work function for use as transparent anodes in organic solar cells (OSCs). The electrical, optical, structural, and morphological properties of IAO films and their work function were investigated as a function of the rapid thermal annealing (RTA) temperature. At an RTA temperature of 600 °C, the IAO film showed a sheet resistance of 23.12 Ohm/square, an optical transmittance of 79.28%, and a work function of 5.21 eV, similar to conventional Sn-doped In₂O₃ (ITO) films. The low resistivity of the IAO film was closely related to oxygen vacancies caused by Ag suboxide formation in the In₂O₃ matrix. A bulk-heterojunction OSC with the optimized IAO anode showed performance comparable to that of an OSC with a reference ITO anode, indicating that the IAO films is a promising anode material for use in OSCs.     

The influence of interfacial barrier engineering on the resistance switching of In2O3：SnO2/TiO2/In2O3：SnO2 device

The I-V characteristics of In2O3：SnO2/TiO2/In2O3：SnO2 junctions with different interracial barriers are inves- tigated by comparing experiments. A two-step resistance switching process is found for samples with two interfacial barriers produced by specific thermal treatment on the interfaces. The nonsynchronous occurrence of conducting filament formation through the oxide bulk and the reduction in the interracial barrier due to the migration of oxygen vacancies under the electric field is supposed to explain the two-step resistive switching process. The unique switching properties of the device, based on interracial barrier engineering, could be exploited for novel applications in nonvolatile memory devices.