Synthesis of carbon microtubules core structure LiFePO4 via a template-assisted method

The carbon microtubules core structure LiFePO₄ is synthesized using a cotton fiber template-assisted method. The crystalline structure and morphology of the product is characterized by X-ray diffraction and field emission scanning electron microscopy. The charge–discharge kinetics of the LiFePO₄ electrode is investigated using cyclic voltammetry and electrochemical impedance spectroscopy. The result shows that the well-crystallized carbon microtubules core structure LiFePO₄ is successfully synthesized. The as-synthesized material exhibits a high initial discharge capacity of 167 mAh g^?1 at 0.2 C rate. The material also shows good high-rate discharge performance and cycling stability, about 127 mAh g^?1 and 94.7 % capacity retention after 100 cycles even at 5.0 C rate.     

Enhanced electrochemical performance of LiFePO4/C prepared by sol–gel synthesis with dry ball-milling

LiFePO₄/C was prepared by a modified aqueous sol–gel route developed by incorporating an additional ball-milling step where the dry gel was milled with the additives of synthetic graphite and carbon black. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), high resolution TEM (HRTEM) and elemental analysis. Results showed that the LiFePO₄/C synthesized by suitable ball-milling process had pure, fine and homogenous LiFePO₄ particles. Results of cyclic voltammetry and charge/discharge plateaus demonstrated that the LiFePO₄/C composite synthesized by milling for 2 h had much better electrochemical kinetics. High performances were achieved with its discharge capacities of 157 mA h g^?1 at 0.1?C and 133 mA h g^?1 at 1?C between 2.5 and 4.2 V (1?C?=?170 mA g^?1). And no obvious capacity fading was observed upon cycling. The simple and convenient synthesis route is promising for large-scale production of LiFePO₄/C.     

Structural and electrochemical properties of LiFe1 − 3x/2Bi x PO4/C synthesized by sol–gel

In this study, LiFe_1???3x/2Bi _x PO₄/C cathode material was synthesized by sol–gel method. From XRD patterns, it was found that the Bi-doped LiFePO₄/C cathode material had the same olivine structure with LiFePO₄/C. SEM studies revealed that Bi doping can effectively decrease the particle sizes. It shortened Li⁺ diffusion distance between LiFePO₄ phase and FePO₄ phase. The LiFe_0.94Bi_0.04PO₄/C powder exhibited a specific initial discharge capacity of about 149.6 mAh g^?1 at 0.1 rate as compared to 123.5 mAh g^?1 of LiFePO₄/C. EIS results indicated that the charge-transfer resistance of LiFePO₄/C decreased greatly after Bi doping.     

A carbothermal reduction method for enhancing the electrochemical performance of LiFePO4/C composite cathode materials

LiFePO₄/C composite cathode material has been synthesized by a carbothermal reduction method using β-FeOOH nanorods as raw materials and glucose as both reducing agent and carbon source. The results indicate that the content of carbon and the morphology of raw material have effect on the electrochemical performance of the final LiFePO₄/C material. Sample LFP14 with a carbon content of 2.79 wt.% can deliver discharge capacities of 158.8, 144.3, 111.0, and 92.9 mAh g^?1 at 0.1, 1, 10, and 15 C, respectively. When decreasing the current from 15 C back to 0.1 C, a discharge capacity of 157.5 mAh g^?1 is recovered, which is 99.2 % of its initial capacity. Therefore, as a kind of cathode material for lithium ion batteries, this LiFePO₄/C material synthesized via a carbothermal reduction method is promising in large-scale production, and has potential application in upcoming hybrid electric vehicles or electric vehicles.     

Propylene oxide-assisted fast sol–gel synthesis of mesoporous and nano-structured LiFePO4/C cathode materials

LiFePO₄/C nanocomposites are synthesized by a propylene oxide-assisted fast sol–gel method using FeCl₃, LiNO₃, NH₄H₂PO₄, and sucrose as the starting materials. It was found that after adding propylene oxide into the solution containing the starting materials, a monolithic jelly-like FePO₄ gel containing lithium and carbon source is generated in a few minutes without controlling the pH value of the solution and a time-consuming heating process. Propylene oxide plays a key role in the fast generation of the precursor gel. The final products of LiFePO₄/C are obtained by sintering the dry precursor gel. The structures, micro-morphologies, and electrochemical properties of the LiFePO₄/C composites are investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, nitrogen adsorption–desorption analysis, electrochemical impedance spectrum, and charge–discharge cycling tests. The results indicate that the LiFePO₄/C composite prepared by sintering the precursor gel at 680 °C for 5 h is about 30 nm in size with a meso-porous structure (the main pore size distribution is around 3.4 nm). It delivers 166.7 and 105.8 mAh g^?1 at 0.2 and 30 C, respectively. The discharge specific capacity is 97.8 mAh g^?1 even at 40 C. The cycling performance of the prepared LiFePO₄/C composite is stable. The excellent electrochemical performance of the LiFePO₄/C composite is attributed to the nano-sized and mesoporous structure of LiFePO₄/C and the in-situ surface coating of the carbon. It was also found that propylene oxide is crucial for the generation of mesoporous and nano-structured LiFePO₄/C.     

Synthesis of high-performance LiFePO4/C composite with a grape bunch structure through the hydrothermal method

The LiFePO₄/C composite with a grape bunch structure was synthesized through the hydrothermal method at 170 °C for 7 h and followed by being fired at 750 °C for 4 h. Commercial Li₂CO₃, (NH₄)₂Fe(SO₄)₂?·?6H₂O, and (NH₄)₂HPO₄ were used as raw materials. Glucose was used as in situ coating carbon source, and the hydroxylated MWCNTs were used as connecting carbon wires which could be embedded into the carbon coating to form a uniform grape bunch structure. The resultant samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), energy dispersive spectrometry (EDS), elementary analysis (EA), Raman spectroscopy, and electrochemical tests. The results show that the grape bunch structure with a low disordered/graphene (D/G) ratio was found to be well dispersed in the LiFePO₄/C composite, and a three-dimensional carbonaceous network was formed which could enhance the electronic conductivity of the LiFePO₄/C composite remarkably. The resultant LiFePO₄/C composite shows a high discharge capacity of 160.3 mAh g^?1 at 0.1 C and 110.9 mAh g^?1 even at 10 C, and the cycling capacity retention rate reaches 99.6 % over 60 cycles. Besides, it also exhibits high conductivity, good reversibility, and excellent stability in EIS and CV tests.     

Electrochemical performance of Mo-doped LiFePO4/C composites prepared by two-step solid-state reaction

To improve the performance of LiFePO₄, LiFe_1?x Mo _x PO₄/C (x?=?0, 0.005, 0.010, 0.015, 0.020, 0.025) cathode materials were synthesized via two-step ball milling solid-state reaction. The prepared samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy, cyclic voltammetry, electrochemical impedance spectra, and galvanostatic charge–discharge test. It is apparent from XRD analysis that Mo doping enlarges the interplanar distance of crystal plane parallel to [010] direction in LiFePO₄. In other words, it widens one-dimensional diffusion channels of Li⁺ along the [010] direction. The results of electrochemical test indicate that the LiFe_0.99Mo_0.01PO₄/C composite exhibits a discharge capacity of 144.8 mAh g^?1 at 1 C rate, a decreased charge transfer resistance of 162.4 Ω and better reversibility of electrode reactions. The present synthesis route is promising and practical for the preparation of LiFePO₄ materials.     

Synthesis and electrochemical performance of LiFePO<Subscript>4</Subscript>/C cathode materials from Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> for high-power lithium-ion batteries

Carbon-coated olivine-structured LiFePO₄/C composites are synthesized via an efficient and low-cost carbothermal reduction method using Fe₂O₃ as iron source at a relative low temperature (600 °C). The effects of two kinds of carbon sources, inorganic (acetylene black) and organic (sucrose), on the structures, morphologies, and lithium storage properties of LiFePO₄/C are evaluated in details. The particle size and distribution of the carbon-coated LiFePO₄ from sucrose (LiFePO₄/SUC) are more uniform than that obtained from acetylene black (LiFePO₄/AB). Moreover, the LiFePO₄/SUC nanocomposite shows superior electrochemical properties such as high discharge capacity of 156 mAh g^?1 at 0.1 C, excellent cyclic stability, and rate capability (78 mAh g^?1 at 20 C), as compared to LiFePO₄/AB. Cyclic voltammetric test discloses that the Li-ion diffusion, the reversibility of lithium extraction/insertion, and electrical conductivity are significantly improved in LiFePO₄/SUC composite. It is believed that olivine-structured LiFePO₄ decorated with carbon from organic carbon source (sucrose) using Fe₂O₃ is a promising cathode for high-power lithium-ion batteries.     

Advanced LiTi<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C anode by incorporation of carbon nanotubes for aqueous lithium-ion batteries

Inferior rate capability is a big challenge for LiTi₂(PO₄)₃ anode for aqueous lithium-ion batteries. Herein, to address such issue, we synthesized a high-performance LiTi₂(PO₄)₃/carbon/carbon nanotube (LTP/C/CNT) composite by virtue of high-quality carbon coating and incorporation of good conductive network. The as-prepared LTP/C/CNT composite exhibits excellent rate performance with discharge capacity of 80.1 and 59.1 mAh g^?1 at 10 C and 20 C (based on the mass of anode, 1 C = 150 mA g^?1), much larger than that of the LTP/C composite (53.4 mAh g^?1 at 10 C, and 31.7 mAh g^?1 at 20 C). LTP/C/CNT also demonstrates outstanding cycling stability with capacity retention of 83.3 % after 1000 cycles at 5 C, superior to LTP/C without incorporation of CNTs (60.1 %). As verified, the excellent electrochemical performance of the LTP/C/CNT composite is attributed to the enhanced electrical conductivity, rapid charge transfer, and Li-ion diffusion because of the incorporation of CNTs.     

Effect of milling time on the performance of bowl-like LiFePO4/C prepared by wet milling-assisted spray drying

LiFePO₄/C was prepared by wet milling-assisted spray drying. The effects of ball-milling time on the characteristics of LiFePO₄/C were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller analysis, cyclic voltammograms, electrochemical impedance spectra, and galvanostatic charge–discharge testing. Bowl-like material was obtained, surrounded by a network of carbon, which display larger specific surface area. The specific surface area of particle first increased and then decreased, as the increasing of ball-milling time; when ball-milling time reach 2.5 h, it showed the largest specific surface area of 29.350 m² g^?1, primary particles with size of ～50 nm, delivered a discharge capacity of 162 mAh g^?1 at 0.5 C and 123 mAh g^?1 at 10 C, and with no capacity loss.     

Nitrogen-doped carbon nanofiber decorated LiFePO<Subscript>4</Subscript> composites with superior performance for lithium-ion batteries

Nitrogen-doped carbon nanofiber (NCNF) decorated LiFePO₄ (LFP) composites are synthesized via an in situ hydrothermal growth method. Electrochemical performance results show that the embedded NCNF can improve electron and ion transfer, thereby resulting in excellent cycling performance. The as-prepared LFP and NCNF composites exhibit excellent electrochemical properties with discharge capacities of 188.9 mAh g^?1 (at 0.2 C) maintained at 167.9 mAh g^?1 even after 200 charge/discharge cycles. The electrode also presents a good rate capability of 10 C and a reversible specific capacity as high as 95.7 mAh g^?1. LFP composites are a potential alternative high-performing anode material for lithium ion batteries.     

Effects of yttrium ion doping on electrochemical performance of LiFePO<Subscript>4</Subscript>/C cathodes for lithium-ion battery

The olivine-type LiFe_1-x Y _x PO₄/C (x?=?0, 0.01, 0.02, 0.03, 0.04, 0.05) products were prepared through liquid-phase precipitation reaction combined with the high-temperature solid-state method. The structure, morphology, and electrochemical performance of the samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), energy-dispersive spectroscopy (EDS), galvanostatic charge-discharge, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). We found that the small amount of Y³⁺ ion-doped can keep the microstructure of LiFePO₄, modify the particle morphology, decrease charge transfer resistance, and enhance exchange current density, thus enhance the electrochemical performance of the LiFePO₄/C. However, the large doping content of Y³⁺ ion cannot be completely doped into LiFePO₄ lattice, but existing partly in the form of YPO₄. The electrochemical performance of LiFePO₄/C was restricted owing to YPO₄. Among all the doped samples, LiFe_0.98Y_0.02PO₄/C showed the best electrochemical performance. The LiFe_0.98Y_0.02PO₄/C sample exhibited the initial discharge capacity of 166.7, 155.8, 148.2, 139.8, and 121.1 mAh g^?1 at a rate of 0.2, 0.5, 1, 2, and 5 C, respectively. And, the discharge capacity of the material was 119.6 mAh g^?1 after 100 cycles at 5 C rates.     

Synthesis and characterization of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>·LiMn<Subscript>0.33</Subscript>Fe<Subscript>0.67</Subscript>PO<Subscript>4</Subscript>/C cathode materials

A new polyanionic cathode material, Li₃V₂(PO₄)₃·LiMn_0.33Fe_0.67PO₄/C for lithium-ion batteries, was synthesized using a sol-gel method and with N,N-dimethyl formamide as a dispersion agent. The analysis of electron transmission spectroscopy and X-ray diffraction revealed that the composite contained two phases. The material has high crystallinity with a grain size of 20–50 nm. The valence states of Mn, V, and Fe in the composite were analyzed by X-ray photoelectron spectroscopy. The electrochemical kinetics in Li₃V₂(PO₄)₃ is effectively enhanced by the incorporation of LiMnPO₄ and LiFePO₄, via structure modification and reduced Li diffusion length. The Li₃V₂(PO₄)₃·LiMn_0.33Fe_0.67PO₄/C materials displayed high rate capacity and steady cycle performance with discharge capacity remained 148 mAh g^?1 after 50 cycles at the rate of 0.2C. In particular, the composite exhibited excellent reversible capacities, with the values of 157, 134, 120, 102, and 94 mAh g^?1 at charge/discharge 0.2, 0.5, 1, 2, and 5C rates, respectively.     

A facile hydrothermal method to prepare LiFePO4/C submicron rod with core–shell structure

Submicron rod LiFePO₄/C has been synthesized via a facile hydrothermal process. The morphology, crystal structure, and charge–discharge performance of the prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and galvanostatic charge–discharge testing. The SEM and TEM illustrate that submicron rods with a width of about 140 nm and a length of up to 400 nm have been obtained. The TEM test also indicates a “core–shell” structure with a 1.5–2 nm carbon shell on the LiFePO₄ core. Even though the separate carbon-coated procedure is not used in this method, the electrochemical behavior results are satisfied. It displays that LiFePO₄/C has highly crystalline and a desirable core–shell structure with uniform carbon film. Galvanostatic battery testing shows that LiFePO₄/C delivers 104 mAh g^?1 at 5 C rates. The highest specific capacity of 166 mAh g^?1 is achieved at 0.1 C rate, and 99.8 % of the initial specific capacitance remained after 30 cycles.     

Synergistic effect of magnesium and fluorine doping on the electrochemical performance of lithium-manganese rich (LMR)-based Ni-Mn-Co-oxide (NMC) cathodes for lithium-ion batteries

Mg-doped-LMR-NMC (Li_1.2Ni_0.15-xMg_xMn_0.55Co_0.1 O₂) is synthesized by combustion method followed by fluorine doping by solid-state synthesis. In this approach, we substituted the Ni²⁺ by Mg²⁺ in varying mole percentages (x = 0.02, 0.05, 0.08) and partly oxygen by fluorine (LiF: LMR-NMC = 1:50 wt%). The synergistic effect of both magnesium and fluorine substitution on electrochemical performance of LMR-NMC is studied by electrochemical impedance spectroscopy and galvanostatic-charge-discharge cycling. Mg-F-doped LMR-NMC (Mg 0.02 mol) composite cathodes shows excellent discharge capacity of ~300 mAh g^?1 at C/20 rate whereas pristine LMR-NMC shows the initial capacity around 250 mAh g^?1 in the voltage range between 2.5 and 4.7 V. Mg-F-doped LMR-NMC shows lesser Ohmic and charge transfer resistance, cycles well, and delivers a stable high capacity of ~280 mAh g^?1 at C/10 rate. The voltage decay which is the major issue of LMR-NMC is minimized in Mg-F-doped LMR-NMC compared to pristine LMR-NMC.     

The facile in situ preparation and characterization of C/FeOF/FeF<Subscript>3</Subscript> nanocomposites as LIB cathode materials

C/FeOF/FeF₃ nanocomposite was synthesized by a facile in situ partial oxidation method. High-resolution transmission electron microscopy (HR-TEM) showed a special texture comprised of interpenetrating nanodomains of FeOF and FeF₃. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements revealed that the introduction of nanodomain FeOF enhanced both the electronic and ionic conductivity of the composite material. Therefore, the improvement of electron and lithium-ion dynamics resulted in the significant enhancement of the electrochemical performances of the material at ambient temperature. At a current density of 20 mA g^?1 within potential range 1.5–4.5 V, the specific capacities of the first ten circles were maintained at about 400 mAh g^?1 _. This material also exhibited excellent cycling capacity retention capability especially for high C rates. When the current density further increased to 100 and 200 mA g^?1, a steady capacity of 80 and 60 mAh g^?1 was observed, respectively. Furthermore, nearly no capacity loss was observed for the followed cycles. The discharge platforms based on intercalation and conversion reaction were also heightened by about 0.4 V, which increased the contribution of high voltage capacities. Compared to C/FeF₃, C/FeOF/FeF₃ is showing more of capacitive behavior, which also contributes to the high specific capacity delivered and is believed to be closely related to the enlarged nanodomain interfaces between two electrochemical active materials. An expansion-cracking-oxidation mechanism was proposed to explain the formation of this interpenetrating nanodomains of FeOF and FeF₃.     

Electrochemical synthesis and lithium storage properties of three-dimensional porous Sn–Co alloy/CNT composite

Three-dimensional (3-D) porous copper with stable pore structure is prepared by electroless plating. 3-D porous Sn–Co alloy/carbon nanotube (CNT) composite is synthesized by electrodeposition using 3-D porous copper as the substrate. The scanning electron microscope results indicate that 3-D porous Sn–Co alloy/CNT composite contains a large amount of interconnected pores with the diameter size of ~3 μm. Upon cycling, the pore structure gradually disappears, but no serious exfoliation appears due to porous structure and reinforcement by CNT. The charge/discharge results demonstrate that the 3-D porous Sn–Co alloy/CNT composite electrode delivers high first reversible specific capacity of 490 mAh g^?1, and remains 441 mAh g^?1 after 60 cycles tested at different current densities. Even at the current density of 3,200 mA g^?1, the reversible specific capacity remains 319 mAh g^?1, which is 65 % of the first specific capacity cycled at the current density of 100 mA g^?1.     

Nanoporous carbon microspheres as matrix of sulfur to prepare sulfur/carbon cathode material for lithium–sulfur battery

A high specific surface area (2798.8 m² g^?1) of nanoporous carbon microsphere (NPCM) is prepared by activated carbon microsphere in hot CO₂ atmosphere, which is used as matrix material of sulfur to prepare NPCM/sulfur composite cathode material by a melt-diffusion method. The NPCM/sulfur composite cathode material with the sulfur content of 53.5% shows high discharge capacity; the initial discharge capacity is 1274 mAh g^?1 which maintains as high as 776.4 mAh g^?1 after 50 cycles at 0.1 C current. At high current density of 1 C, the NPCM/sulfur cathode material still shows initial discharge capacity of 830.3 mAh g^?1, and the reversible capacity retention is 78% after 50 cycles. To study the influence of different sulfur content of NPCM/sulfur cathode material to the performance of Li–S battery, the different sulfur content of NPCM/sulfur composite cathode materials is prepared by changing the thermal diffusion time and the ratio of sulfur powder to NPCM. The performance of NPCM/sulfur cathode material with different sulfur content is studied at a current of 0.1 C, which will be very important to the preparation of high-performance sulfur/carbon cathode material with appropriate sulfur content.     

NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> polyhedra with controllable particle size as high-performance anode for lithium-ion battery

Different particle sizes of dodecahedron precursors are synthesized by controlling the polarity of the solution. Through the results of scanning electron microscope (SEM) images, it can be found that different particle sizes of precursors present obvious edge angles and their morphology can be well retained after annealing. X-ray diffraction (XRD) measurements suggest that the annealed polyhedral products are pure single-phase NiCo₂O₄. When tested as lithium-ion battery anode, 0.5 μm NiCo₂O₄ polyhedra exhibits a specific capacity of 1050 mAh g^?1 at 0.1 C at the 60th cycle, which was higher than theoretical capacity of single metal oxide (NiO 718 mAh g^?1 and Co₃O₄ 890 mAh g^?1). It also exhibits the highest rate capability with an average discharge capacity of 890, 700, 490, 330, and 300 mAh g^?1 at 0.5, 2, 4, 8, and 10 C, respectively. Those advantages are attributed to that small-sized particle with great surface areas decrease the actual current density at the surface and inner of the prepared electrode.     

A novel and shortcut method to prepare ionic liquid gel polymer electrolyte membranes for lithium-ion battery

The ionic liquid polymer electrolyte (IL-PE) membrane is prepared by ultraviolet (UV) cross-linking technology with polyurethane acrylate (PUA), methyl methacrylate (MMA), ionic liquid (Py₁₃TFSI), lithium salt (LiTFSI), ethylene glycol dimethacrylate (EGDMA), and benzoyl peroxide (BPO). N-methyl-N-propyl pyrrolidinium bis(trifluoromethanesulfonyl)imide (Py₁₃TFSI) ionic liquid is synthesized by mixing N-methyl-N-propyl pyrrolidinium bromide (Py₁₃Br) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The addition of Py₁₃TFSI to polymer electrolyte membranes leads to network structures by the chain cross-linking. The resultant electrolyte membranes display the room temperature ionic conductivity of 1.37 × 10^?3 S cm^?1 and the lithium ions transference number of 0.22. The electrochemical stability window of IL-PE is about 4.8 V (vs. Li⁺/Li), indicating sufficient electrochemical stability. The interfacial resistances between the IL-PE and the electrodes have the less change after 10 cycles than before 10 cycles. IL-PE has better compatibility with the LiFePO₄ electrode and the Li electrode after 10 cycles. The first discharge performance of Li/IL-PE/LiFePO₄ half-cell shows a capacity of 151.9 mAh g^?1 and coulombic efficiency of 87.9%. The discharge capacity is 131.9 mAh g^?1 with 95.5% coulombic efficiency after 80 cycles. Therefore, the battery using the IL-PE exhibits a good cycle and rate performance.