O2/CO2燃烧方式下煤中有机/无机硫的释放特性

首先用重液浮选将一种烟煤分为高(＞2.0 g/cm3)、中(1.4～2.0 g/cm3)和低(＜1.4 g/cm3)三个密度段,并采用三态硫化学分析,发现无机硫(外在黄铁矿为主)主要赋存于高密度煤中,有机硫主要赋存于低密度煤中,几乎全部硫酸盐硫、部分有机硫和少量无机硫(内在黄铁矿)赋存于中密度煤中.其次在程序升温条件下研究了分密度煤中硫的释放特性以及含硫物相的浓度变化规律,探讨了有机/无机硫析出特性的影响机理.结果显示:在O2/CO2气氛下,高、中密度煤SO2析出曲线都有尖峰并呈双峰分布,在较短时间及较窄温度范围反应完全;与之相反,低密度煤释放曲线平坦且无明显峰,在较长时间和较宽温度范围均有析出;相对于O2/N2气氛,O2/CO2燃烧方式促进了硫以COS/SO3等物相生成,同时提高了煤灰中矿物质自固硫能力,从而降低了SO2的排放.     

高浓度CO2气氛下燃煤氮、硫污染物的释放特性

采用污染物在线分析仪、气相便携红外分析仪研究了程序升温条件下改变氧化介质时煤中氮,硫的释放特性以及含硫物相的浓度变化规律,探讨了不同气氛,CO2浓度与O2浓度单独变化时对NO、SO2析出特性的影响机理.结果表明:O2/CO2燃烧气氛下NO、SO2排放峰值及总量均低于O2/N2气氛.CO2气氛下烟气中存在大量的CO,有利于NO的降解,同时也促进了烟气中其他含硫物相的形成,随着CO2浓度的增加,特别是在燃烧后期,NO、SO2的排放显著降低.O2浓度改变对NO和SO2的释放影响不同:O2浓度升高促进了SO2的析出;但是O2浓度在一定范围内增加对NO的排放并无明显影响,随着O2浓度进一步增加,NO的释放峰向低温区迁移,同时排放量降低.     

煤温和热解过程中汞释放形态及分布规律研究

本文选取两种贵州高汞煤,在200～800℃的温度范围内,采用程序升温反应系统加热,利用美国EPA推荐的Ontario-Hydro方法捕捉不同形态汞。研究了在N₂气氛和微氧化性气氛下温和热解过程中汞的释放和形态分布规律。实验结果表明:温度是影响煤温和热解过程中汞释放的主要因素,煤中汞释放率随着温度的升高而明显升高,当热解温度为600℃时,汞释放率可达90%左右。在微氧化性气氛下,汞的释放率随着氧气体积分数的升高而增大。元素汞（Hg⁰）是气态汞释放的主要形态,热解停留时间及热解气氛对气态汞的释放形态也存在影响较大。     

O2/CO2气氛下石灰石煅烧及烧结特性研究

本文研究了在O2/CO2气氛下石灰石的煅烧和烧结特性.结果表明,空气气氛下煅烧所得CaO的孔隙率和比表面积均较O2/CO2气氛下的大,但O2/CO2气氛下煅烧所得CaO具有更大的最可几孔径.石灰石在O2/CO2气氛下1000℃煅烧时的产物具有最大的比孔容积和比表面积,且石灰石煅烧产物CaO的比孔容积和比表面积均随气氛中CO2浓度的增加而下降,在低CO2浓度下下降较为迅速,而在高CO2浓度下下降逐渐趋于平缓.在延长相同烧结时间的情况下,O2/CO2气氛下CaO孔结构受烧结影响的程度要比空气气氛下轻微.     

CO2-3掺杂纳米羟基磷灰石晶体的合成与表征

CO2-3掺杂是提高纳米羟基磷灰石（n-HA）生物活性的有效方法之一。以 Ca（NO3）2·4H2O 和Na3PO4·12H2O为主要原料，Na2CO3作为CO2-3来源，合成纳米碳羟基磷灰石（n-CHA）晶体。采用TEM ， XRD ，FTIR ，RS对合成晶体形貌和结构进行表征。结果表明：合成的n-HA晶体长度约为60～80 nm ，宽度在20～30 nm之间，形状为针状，具有良好的结晶度，与自然骨磷灰石形貌相似；n-CHA晶体随CO2-3掺入量的增加，结晶度降低；合成的 n-CHA晶体的晶胞参数 a值随着CO2-3加入量的增大不断收缩，但 c值增大，参数比c/a值增大，符合B型取代（取代PO3-4）的晶胞参数变化规律。红外谱图中，872 cm -1附近出现AB混合型取代（同时取代O H -，PO3-4）的CO2-3面外弯曲振动特征红外峰，同时CO2-3的不对称伸缩振动红外峰在1454和1420 cm -1附近出现分裂峰，1540 cm -1附近出现弱CO2-3峰；1122 cm -1附近出现CO2-3对称伸缩振动拉曼峰，1071 cm -1附近出现CO2-3的B型替代特征拉曼峰，通过计算PO3-4，CO2-3，O H -拉曼峰的积分面积比PO3-4/CO2-3，O H -/CO23，PO3-4/O H -，表明CO2-3在替换时，先以B型为主，随着CO2-3掺入量的增加，发生A型替代（取代O H -）。实验结果表明，合成的磷灰石晶体为B型取代（取代PO3-4）为主的AB混合型取代的 n-CHA。与人骨磷灰石晶体在形态、尺寸、晶体结构和生长方式上具有相似性，可称为类骨磷灰石。     

掺杂碱金属与碱土金属的CuO-CeO_2催化剂的漫反射红外光谱分析

CuO-CeO2系列催化剂是高效的CO选择性氧化反应的催化剂,通过原位漫反射红外光谱对掺杂碱金属和碱土金属氧化物的CuO-CeO2催化剂表面的吸附物种进行了研究。结果表明CuO-CeO2系列催化剂上,2 106 cm-1处出现CO的红外吸附峰。在反应气氛中,此峰的强度随着温度先升高后降低,说明Cu+是CO主要的活性吸附中心。低温下催化剂表面吸附的CO主要以可逆形式脱附出来,而高温下CO则以不可逆的形式脱附出来。催化剂表面在3 660 cm-1处出现尖锐的红外峰,归属于CeO2经还原产生的Ce-(OH)2偕式基团。在1 568,2 838和2 948 cm-1附近处出现甲酸根的红外谱峰,以及1 257和1 633 cm-1处出现碳酸根物种的红外峰。甲酸根物种是气相的CO与表面的羟基反应生成的产物,该物种的C—H键断裂生成碳酸根物种,这两物种均会降低催化剂的高温活性。Cu1Li1Ce9Oδ催化剂出现较强的CO2和甲酸根的红外峰,温度高于180℃时,该催化剂上还能看到微弱的CO红外峰,说明锂离子的给电子性质有利于提高Cu1Li1Ce9Oδ催化剂上CO的不可逆脱附,抑制氢的活化吸附,同时促进了甲酸根物种的生成。低温下Cu1Mg1Ce9Oδ和Cu1Ba1Ce9Oδ催化剂上CO的吸附量较多,但主要以可逆脱附形式脱附出来,对CO选择性氧化没有贡献。     

不同变质程度煤燃烧反应性及FTIR分析其热解过程结构变化

利用TG/DTA 6300的热重分析仪对胜利褐煤(SL)、神华烟煤(SH)与塔旺陶勒盖无烟煤(TT)三种不同变质程度的原煤进行空气气氛下燃烧反应;通过FTIR(傅里叶变换红外光谱)分析了三种煤样及不同终温下固定床热解半焦的官能团组成;运用数学高斯函数对FTIR曲线重叠吸收峰进行分峰拟合,利用拟合峰面积计算FTIR的芳香度指数(R)、芳香结构稠合指数(D)及有机成熟度指数(C)结构参数。结果表明： SL,SH与TT煤着火温度分别为299.3,408.2及441.0℃;最大失重速率峰温度分别为348.6,480.5及507.0 ℃,即随煤样变质程度的不同,着火点和最大失重速率温度都不同程度提高。煤中官能团结构较复杂,不同变质程度的煤样的红外光谱曲线中均可以观察到羟基(—OH);脂肪烃(—CH₂,—CH₃);芳环(CC); 含氧官能团(CO, C—O)等主要官能团的振动吸收峰。随着热解炼焦温度的升高,三种煤样中脂肪烃类(—CH₂—,—CH₃)红外振动吸收峰均逐渐减小;炼焦后CO在1 700 cm-1伸缩振动峰在炼焦温度到达550 ℃时基本消失;SL原煤样在1 000～1 800 cm-1 含氧官能团吸收峰区域红外曲线更为复杂,随炼焦温度升高较之其他煤样变化最为显著;而SH及TT煤芳环CC吸收峰在温变过程中峰位及峰强度均无显著变化。通过R,D及C值随热解终温的变化曲线,三种变质程度煤在热解反应过程中主体官能团变化趋势存在差异。     

TG-FTIR法研究低变质煤共热解过程气体的析出规律

采用热重-红外联用技术（TG-FTIR）对比研究了陕北低变质粉煤（SJC）与重油（HS）、焦煤（JM）、液化残渣（DCLR）共热解过程中气相产物的析出特性。研究表明,随热解温度升高,SJC与HS,JM,DCLR的共热解过程均可分为三个阶段。第一阶段表现为原料表面吸附物的释放,第二阶段发生解聚和分解反应,随温度继续升高,第三阶段形成更为稳定的半焦。在热解第二阶段中均存在煤与添加剂之间的协同效应,SJC作为主要的供氢体,热解产生的氢自由基与HS,JM,DCLR热解产生的小分子自由基碎片之间发生相互作用生成焦油和煤气。SJC和SJC+DCLR在450 ℃附近的温度区间内热解反应进行的更加充分,大部分N元素转移到了焦油组分中。热解过程气相产物中H₂O和酚类物质、含N杂环物质及CO的析出伴随着热解的整个温度区间,SJC+JM和SJC+HS热解过程含N物质的转移主要集中在400~650 ℃区间,CH₄和脂肪烃类物质的析出最高峰出现在450 ℃附近,而SJC+DCLR和SJC则出现在550 ℃。JM,HS及DCLR的添加可促使焦油中芳香族化合物的析出,SJC+JM与SJC+HS热解过程芳香族物质大量析出的温度区间在400~550 ℃。该研究结果为低变质粉煤的清洁转化与提质分级新技术的研究开发提供理论依据,对低变质煤的增值利用具有重要的意义。     

O2/CO2条件下煤粉燃烧火焰特性的实验研究

本文利用平面火焰曳带流反应系统,对O2/CO2气氛下的煤粉火焰进行了实验研究.以期通过此实验研究,对后期的实验室规模的实验研究起到指导作用.结果表明:O2/CO2气氛下CO2的存在、氧分压的大小以及煤中的水分含量均对煤粉火焰有较大影响.     

CO32-掺杂纳米羟基磷灰石晶体的合成与表征

CO32-掺杂是提高纳米羟基磷灰石(n-HA)生物活性的有效方法之一。以Ca(NO3)2·4H2O和Na3PO4·12H2O为主要原料,Na2CO3作为CO2-3来源,合成纳米碳羟基磷灰石(n-CHA)晶体。采用TEM,XRD,FTIR,RS对合成晶体形貌和结构进行表征。结果表明:合成的n-HA晶体长度约为60~80nm,宽度在20~30nm之间,形状为针状,具有良好的结晶度,与自然骨磷灰石形貌相似;n-CHA晶体随CO2-3掺入量的增加,结晶度降低;合成的n-CHA晶体的晶胞参数a值随着CO2-3加入量的增大不断收缩,但c值增大,参数比c/a值增大,符合B型取代(取代PO3-4)的晶胞参数变化规律。红外谱图中,872cm-1附近出现AB混合型取代(同时取代OH-,PO3-4)的CO2-3面外弯曲振动特征红外峰,同时CO2-3的不对称伸缩振动红外峰在1 454和1 420cm-1附近出现分裂峰,1 540cm-1附近出现弱CO2-3峰;1 122cm-1附近出现CO2-3对称伸缩振动拉曼峰,1 071cm-1附近出现CO2-3的B型替代特征拉曼峰,通过计算PO3-4,CO2-3,OH-拉曼峰的积分面积比PO3-4/CO2-3,OH-/CO23,PO3-4/OH-,表明CO2-3在替换时,先以B型为主,随着CO2-3掺入量的增加,发生A型替代(取代OH-)。实验结果表明,合成的磷灰石晶体为B型取代(取代PO3-4)为主的AB混合型取代的n-CHA。与人骨磷灰石晶体在形态、尺寸、晶体结构和生长方式上具有相似性,可称为类骨磷灰石。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.