Sn掺杂ZnO薄膜的室温气敏性能及其气敏机理

采用化学气相沉积方法在预制好电极的玻璃基底上制备出Sn掺杂ZnO薄膜和纯ZnO薄膜. 两种样品典型的形貌为四足状ZnO晶须, 其直径约为150-400 nm, 呈疏松状结构. 气敏测试结果显示Sn掺杂ZnO薄膜具有优良的室温气敏性, 并对乙醇具有良好的气敏选择性, 而纯ZnO薄膜在室温条件下对乙醇和丙酮均没有气敏响应. X射线衍射结果表明两种样品均为六方纤锌矿结构. Sn掺杂ZnO样品中没有出现Sn及其氧化物的衍射峰, 其衍射结果与纯ZnO样品对比, 衍射峰向小角度偏移. 光致发光结果表明, Sn掺杂ZnO薄膜与纯ZnO薄膜均出现紫外发光峰和缺陷发光峰, 但是Sn的掺杂使得ZnO的缺陷发光峰明显增强. 将Sn掺杂ZnO样品在空气中退火后, 其室温气敏性消失, 说明Sn掺杂ZnO样品的室温气敏性可能与其缺陷含量高有关. 采用自由电子散射模型解释了Sn掺杂ZnO薄膜的室温气敏机理.     

退火温度对溶胶-凝胶法制备Na掺杂 ZnO薄膜的结构和光学特性的影响

采用溶胶-凝胶旋涂法在Si(100)衬底上制备Na掺杂ZnO薄膜,退火温度分别为873,973,1 073 K。研究了退火温度对Na掺杂ZnO薄膜形貌、微观结构和光学性能的影响。室温光致发光谱显示,在973 K下退火的样品具有中心位于361 nm处尖锐而强的紫外发光峰,在388,425 nm处各有一个比较弱的紫色和蓝色发光峰,在可见光范围内发光峰的强度很弱。     

In掺杂的ZnO纳米棒的共振Raman光谱研究

本文报道In掺杂ZnO纳米棒的成功制备和对其结构以及光荧光性能的详尽研究。在室温条件下ZnO的共振拉曼谱线容易受到很强的荧光干扰, 甚至导致共振拉曼谱线完全被湮没。微量In掺杂入ZnO纳米棒中, 调控紫外发光峰由378 nm(纯ZnO)红移至397 nm; 另外, 在制备过程中引入过量的氧, 在样品中产生大量缺陷, 降低了ZnO的紫外近带边发光峰强度。这两方面导致在室温下可清楚的观察到In掺杂ZnO纳米棒的6阶LO拉曼峰。     

以PVP纳米纤维为模板采用原子层沉积法制备MgxZn1-xO纳米纤维及其光学性质研究

采用静电纺丝方法制备聚乙烯吡咯烷酮(PVP)纳米纤维,并以其为模板采用原子层沉积(ALD)方法制备不同Mg掺杂浓度的MgxZn1-xO纳米纤维。研究了不同Mg掺杂浓度对复合纳米纤维结构和光学性质的影响。利用场发射扫描电子显微镜(FESEM)、光致发光(PL)和紫外-可见光(UV-Vis)吸收谱对样品测试并进行表征分析。结果表明,Mg元素的掺入并没有改变ZnO纳米纤维的形貌,所有样品的表面形貌极其相似,只是掺杂后纤维直径有所增大;随着Mg掺杂浓度的增加吸收边逐渐发生蓝移,表明所制备MgxZn1-xO纤维的带隙具有可调节性。与此同时,在PL谱中可以观察到样品的紫外(UV)发光峰从377nm移动至362nm,且与不掺杂的样品相比,MgxZn1-xO纳米纤维的UV发光强度明显增强。通过这种方法可以合成组分可控的MgxZn1-xO纳米纤维。在ZnO中掺入Mg元素可以有效地提高ZnO-PVP纳米纤维的禁带宽度以及UV发射强度。     

水热法制备钼掺杂ZnO纳米结构及其光学特性研究

用水热法以Zn(NO3)2·6H2O和NaOH为原料,分别以十六烷基三甲基溴化铵(CTAB)、十二烷基硫酸钠(SDS)、聚乙烯吡咯烷酮-K30(PVP-K30)、聚乙二醇400(PEG400)、乙二胺四乙酸(EDTA)为添加剂,制备钼掺杂的纳米ZnO。扫描电镜(SEM)结果表明,通过改变添加剂的种类可以合成不同形貌钼掺杂的ZnO;X射线衍射(XRD)结果表明,掺杂的ZnO纳米粉体为六方纤锌矿结构,随着钼掺杂浓度的增加,衍射峰强度明显增大,结晶质量得到明显改善;室温下的光致发光(PL)图谱表明,掺杂的样品在385 nm处有一紫光发射峰,在约572 nm处有一绿发光射峰,Mo掺杂后明显提高了样品的发光强度。     

碱金属改性的纳米氧化锌基荧光材料

研究了Zn （NO3）2·6H2O、CO （NH2）2、R-C6H4-SO3Na、Eu2O3和LiNO3为原料,通过均匀沉淀法制备了Eu3＋、Li＋共掺杂的纳米ZnO材料,并通过改变Li＋的掺杂比例来研究纳米氧化锌基材料的发光性能,用XRD、紫外和荧光等分析手段对样品进行表征.结果表明：制得的纳米粉体粒径在50nm左右,引入Li＋后增强了纳米ZnO∶Eu3＋材料的紫外可见光吸收和红色发光性能,且与Li＋的掺杂浓度有关,当Li＋∶Eu3＋的摩尔比为0.6时,其在601nm处的特征峰最强.     

高分子网络凝胶法制备ZnO超细粉体及其光学性能

采用高分子网络凝胶法制备球形ZnO超细粉体。通过聚乙烯醇(PVA)亚浓溶液交联网络的空间位阻作用,经过烧结,获得了具有球形形貌的粒径为1~3μm的ZnO粉体颗粒。利用X射线衍射(XRD)、扫描电镜(SEM)分析了不同PVA浓度以及退火温度对产物形貌、结构的影响,发现在PVA溶液浓度为5%,并且经500℃热处理所形成的ZnO球形颗粒最为均匀规整。研究了球形ZnO粉体的光致发光性能,室温下经325nm波长激发,观察到两个中心波长分别位于407,468nm的微弱的荧光发射带,在合适温度下,在385nm处还出现了较强的紫外峰。PL光谱表明,退火温度对ZnO的光致发光影响较大,随着退火温度升高,由于表面缺陷和结晶性能发生变化,407nm处发射峰逐渐减弱消失,而紫外发光先增强后减弱,经500℃热处理样品的紫外发光性能达到最佳。     

硫掺杂ZnO纳米线的电化学制备及发光特性

"采用电场辅助电化学沉积法,利用阳极氧化铝模板模板制备了高度择优取向的硫掺杂ZnO单晶纳米线．X射线衍射仪、隧道电子显微镜、选取电子衍射对所得样品的结构、形貌分析表明,所得纳米线是沿(101)择优取向的六方纤锌矿结构单晶纳米线,长约几十微米、平均直径约70 nm. X射线光电子能谱对化学组成的分析进一步证实掺杂硫原子的存在．用荧光光谱仪(PL)对S掺杂前后的ZnO纳米线进行光学特性测量发现,S掺杂较大地改变了ZnO纳米线的发光性质．在PL谱中,除了有典型的ZnO纳米线在378、392 nm处的强紫外发光峰     

La、Ce掺杂ZnO纳米晶的发光特性

共沉淀法制备了稀土镧、铈掺杂的ZnO半导体纳米晶。X射线衍射(XRD)结果表明:掺杂的ZnO纳米晶为六方纤锌矿结构,随掺杂浓度增加ZnO粒径减小。对铈掺杂纳米ZnO,以波长380nm激发,在443nm处出现了半峰宽较窄的强的蓝光发射峰;镧掺杂ZnO纳米晶则为从418~610nm的多峰宽带发射。     

掺Sb纳米ZnO的光致发光的研究

用柠檬酸盐法合成了不同掺杂浓度的纳米ZnO,粒径约为15nm。探讨了Sb掺杂对ZnO光致发光峰的影响。随着掺杂量的提高,样品的发射峰从428nm移至444nm。未掺杂ZnO的发光主要是源于电子从锌填隙形成的缺陷能级到价带顶的跃迁;随着掺杂量的提高,体系的氧空位增加,从而使得电子从氧空位所形成的缺陷能级到价带顶的跃迁占据主导,光致发射峰向长波方向移动。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.