ZnO：V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO:V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO:V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO:V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

ZnO∶V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO∶V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO∶V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO∶V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

Fe,Co共掺杂ZnO薄膜结构及发光特性研究

采用溶胶凝胶法在玻璃衬底上制备了Fe,Co共掺Zn0.9FexCo0.1-xO(x=0,0.03,0.05,0.07)系列薄膜.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子谱(XPS)和光致发光(PL)谱对薄膜样品的表面形貌、晶体结构、成分和光学性能进行了研究.XRD结果表明所有ZnO薄膜样品都呈六方纤锌矿结构,在样品中没有观察到与Fe和Co相关的团簇,氧化物及其他杂相的衍射峰,表明共掺杂改善了Fe或Co在ZnO的分散性.XPS测试结果揭示样品中Co离子的价态为+2价;Fe离子的价态为+2价和+3价共存,但Fe相对浓度的增大导致Fe3+含量增加.所有样品的室温光致发光谱(PL)均观察到紫外发光峰和蓝光双峰,其中Fe,Co共掺ZnO薄膜的紫外发光峰较本征ZnO出现蓝移,蓝光双峰峰位没有变化,但发光强度有所减弱;而掺杂ZnO薄膜的绿光发光峰几乎消失.最后,结合微结构和成分分析对薄膜样品的发光机理进行了讨论.     

Fe掺杂对溶胶凝胶法制备的ZnO: Ni薄膜结构及发光特性的影响

采用溶胶凝胶法在玻璃基片上制备了ZnO及Ni, Fe共掺杂的Zn_0.95-xNi_0.05Fe_xO (x=0, 0.005, 0.01, 0.03, 0.05) 薄膜. 通过扫描电镜(SEM) 和X射线衍射(XRD) 研究了薄膜样品的表面形貌和晶体结构. 结果表明所有样品都具有(002) 择优取向, Fe掺杂导致ZnO: Ni薄膜的晶体质量变差, 晶粒尺寸减小, 但适当的Fe掺杂有利于获得致密、 均匀的薄膜. XPS测试结果表明样品中Ni离子的价态为+2价, Fe离子的价态为+2价和+3价.室温光致发光(PL) 测量表明, 所有样品均观察到较强的紫外发光峰, 蓝光双峰和绿光发光峰. ZnO: Ni薄膜的发光强度可以通过Fe掺杂进行有效调节. 进而我们讨论了Ni, Fe共掺杂ZnO样品的发光机理.     

溶胶-凝胶法制备ZnO薄膜及其光致发光性质

利用溶胶-凝胶法在石英衬底上制备了ZnO薄膜,通过测量样品的透射谱、X射线衍射谱、扫描电子显微镜(SEM)图像和光致发光谱研究了其结构特征和发光性质.结果表明:在衍射角2θ=34.32°处出现了对应(002)晶面的强衍射峰,ZnO膜呈多晶状态,具有六角纤矿晶体结构和良好的C轴择优取向,薄膜中颗粒的平均粒径为56nm;光致发光呈多发光峰状,有中心波长为378nm的紫带,520nm绿带,446nm附近的蓝带以及发现未见报道过的绿带以后中心波长为586nm和570nm两个弱发射峰.实验结果表明,制备的ZnO薄膜具有发光特性,但内部与深能级发射相关的结构缺陷浓度还是较高,样品中两个低能量光致发光应来源于晶粒间界的缺陷能级,多缺陷能级导致了多发射峰的光致发光谱.     

Ni掺杂ZnO薄膜的结构与光学特性研究

使用射频磁控溅射法成功制备了不同掺杂浓度（0—7at.%）的ZnO:Ni薄膜.X射线衍射的θ-2θ和摇摆曲线扫描结果表明,5at.%Ni掺杂ZnO薄膜具有沿c轴方向最佳的择优取向生长特性,（002）衍射峰向大角度方向移动揭示了Ni杂质被掺入ZnO晶格中占据Zn位.ZnO:Ni薄膜具有较好的可见光透明特性,拟合发现薄膜的光学带隙随Ni掺杂量的增加由3.272 eV线性降低到3.253 eV.未掺杂薄膜在550 nm处呈现出一个绿色发光峰,掺入Ni杂质后薄膜主要表现了以430 nm为中心的蓝色发光,分析认为它们分别源于薄膜中O空位和Zn填隙缺陷发光. 关键词： ZnO:Ni薄膜 结构特性 光学带隙 光致发光     

氟掺杂的氧化锌薄膜的结构和光学特性

通过热氧化氟化锌(ZnF2)薄膜的方法制备出氟掺杂的多晶ZnO薄膜,ZnF2薄膜是利用电子束蒸发方法沉积在Si(100)衬底得到的。利用X射线衍射和X射线电子能谱研究了ZnF2薄膜向ZnO的转变过程。实验结果表明,在400℃退火30min的条件下能够获得六方纤锌矿结构的ZnO：F薄膜。对ZnO：F薄膜的室温光致发光谱可以观察到位于379nm、半峰全宽为73meV的紫外发射峰,而相应于缺陷的深能级发射则完全猝灭。表明ZnO中残留的F能够有效地增强激子的发光,同时使缺陷发光强度明显降低。对F掺杂对ZnO的发光性能的影响进行了讨论。     

花状的氧化锌纳米结构的制备及其光学性能

以氢氧化钠和六水合硝酸锌为反应物,在未使用任何表面活性剂的简单反应体系中制得了玫瑰花状ZnO纳米结构,采用X射线衍射(XRD)、扫描电子显微镜(SEM)和室温荧光光谱对产物的晶体结构、形貌和发光性质进行了表征和分析.测试结果表明,所得产物为六方纤锌矿结构ZnO纳米材料,产物结晶完整,尺寸较均匀.这种简单水热法制备的ZnO纳米材料仅在384nm处具有一个较强的紫外发光峰,而在黄绿区几乎没有发光峰,进一步证明了所得样品结晶良好,没有缺陷和空位.以上结果表明所制备的氧化锌纳米材料具有优异的紫外光发射能力.     

Co与Cu掺杂ZnO薄膜的制备与光致发光研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co, Cu单掺杂及Co,Cu共掺杂ZnO薄膜.用金相显微镜观察了Co与Cu掺杂对ZnO薄膜形貌的影响.X射线衍射（XRD）研究揭示所有ZnO薄膜样品都存在（002）择优取向,在Cu单掺的ZnO薄膜中晶粒尺寸最大.对所有样品的室温光致发光测量都观察到较强的蓝光双峰发射和较弱的绿光发射,其中长波长的蓝光峰和绿光峰都能够通过掺杂进行控制.对不同掺杂源的ZnO薄膜发光性能进行了分析,认为蓝光峰来源于电子由导带底到锌空位能级的跃迁及锌填隙到价带顶的跃迁,绿光峰是由于掺杂造成的 关键词： ZnO薄膜 溶胶-凝胶 Co Cu掺杂 光致发光     

Co,Sn共掺ZnO薄膜结构与光致发光的研究

采用溶胶-凝胶旋涂法在玻璃衬底上制备了Co,Sn掺杂ZnO系列薄膜.通过金相显微镜和X射线衍射(XRD)研究了Co与Sn掺杂对薄膜的表面形貌和微结构的影响.XRD结果表明,所有ZnO薄膜样品都存在(002)择优取向,特别Sn单掺ZnO薄膜的c轴择优取向最为显著,而且晶粒尺寸最大.XPS测试表明样品中Co和Sn的价态分别为2+和4+,证实Co²⁺,Sn⁴⁺进入了ZnO的晶格.室温光致发光谱(PL)显示在所有的样品中都有较强的蓝光双峰发射和较弱的绿光发 关键词： ZnO薄膜 溶胶-凝胶 掺杂 光致发光     

Optoelectronics and formaldehyde sensing properties of tin-doped ZnO thin films

Sn-doped ZnO thin films were deposited on clean glass substrates using the chemical spray pyrolysis technique. XRD analyses confirm stable ZnO hexagonal wurtzite structure of the films with crystallite size in the range of 20–28 nm. The surface roughness of the films increases on Sn doping, which favors to higher adsorption of oxygen species on the film surface, resulting in higher gas response. Optical studies reveal that the band gap decreases on Sn doping. All the films show near band edge emission, and on Sn doping the luminescence peak intensity has been found to increase. Photocurrent in the 1.5 at.% doped film enhances about three times to that observed in the undoped ZnO film. Among all the films examined, the 1.5 at.% Sn-doped film exhibits the maximum response (～94.5 %) at the operating temperature of 275?°C for 100 ppm concentration of formaldehyde, which is much higher than the response (～35 %) in the undoped film. The gas response of the film is attributed to the chemisorption of oxygen on the film surface and the subsequent reaction between the adsorbed oxygen species and the formaldehyde molecules.     

Optical and room temperature sensing properties of highly oxygen deficient flower-like ZnO nanostructures

Oxygen deficient zinc oxide (ZnO) thin films were deposited electrochemically on glass substrates which are pre-sputtered with pure zinc (Zn) metal. Well-arranged flower-like nanostructures are observed from the SEM micrographs. The purity and crystallinity of the deposited films were confirmed from X-ray diffraction studies supported by Raman studies. The broad and intense defect induced green emission confirms the high oxygen deficiency in the nanostructures. The flower-like structures as well as the oxygen defects present in the system are indeed very suitable for gas and chemical sensing applications. These films were used for room temperature sensing of three different chemicals viz. acetone, ethanol and ammonia. The sensor was found to be insensitive to the change in different concentrations of acetone while it was found to be sensitive to different concentrations of ethanol and ammonia. The sensor is most suitable for sensing ammonia at room temperature.     

Nitrogen oxides and ammonia sensing characteristics of SILAR deposited ZnO thin film

Pure and Sn, Ni doped ZnO thin films were deposited on glass substrates using a novel successive ionic layer adsorption and reaction (SILAR) method at room temperature. Microstructures of the deposited films were optimized by adjusting growth parameters. The variation in resistivity of the ZnO film sensors was performed with rapid photothermal processing (RPP). The effect of rapid photothermal processing was found to have an important role in ZnO based sensor sensitivity to NO₂, NH₃. While the undoped ZnO film surface exhibited higher NH₃ sensitivity than that of NO₂, an enhanced NO₂ sensitivity was noticed for the ZnO films doped with Sn and higher NH₃ sensitivity was obtained by Ni doping.     

Studies on thin films of TiO2 for resistance-based sensing of ethanol vapor at room temperature

We investigate the gas sensing properties of TiO₂ thin films prepared by spin coating. The presence of anatase and rutile phases in the sample was confirmed by powder X-Ray diffraction study. The thin film was characterized by FE-SEM and EDAX. The TiO₂ thin films were found to have good sensitivity towards ethanol compared to other gases. The sensing studies revealed the ethanol sensing properties of the thin film at room temperature even at lower concentrations. The response and selectivity of the film were also discussed in detail.     

单根Sb掺杂ZnO微米线非平衡电桥式气敏传感器的制作与性能

通过使用化学气相沉积法,成功制备出超长、大尺寸的Sb掺杂ZnO微米线.基于非平衡电桥原理,利用单根Sb掺杂ZnO微米线作为非平衡电桥的一个桥臂,制作出了可以在室温环境下工作的气敏传感器原型器件.结果表明:室温下测得该传感器对20,50,100和200 ppm(1 ppm=10^-6)不同浓度的丙酮及乙醇气体的响应-恢复曲线均呈现为矩形形状,在空气及被测气体中均有稳定的电流值,并随着探测气体浓度的增大,器件的响应值也在逐渐增加.此外,还发现器件对丙酮气体具有更好的选择性,当丙酮气体浓度为200 ppm时,该传感器的响应时间为0.2 s,恢复时间为0.3 s,响应度高达243%.通过与普通电导式气敏传感器对比发现,采用这种非平衡电桥结构传感器可以明显地提高响应度,使响应和恢复时间更快.此外,还研究了器件的气体探测机理.     

Characterization and ammonia sensing properties of pure and?modified ZnO films

Zinc oxide (ZnO) films have been prepared by thermal oxidation of pre-deposited zinc films on the glass substrate kept at room temperature. These films were surface modified by dipping them into an aqueous solution (0.1 M) of lithium chloride (LiCl) and aluminium chloride (AlCl₃) followed by firing at 500°C. Based on X-ray diffraction results it is observed that modification of pure ZnO by lithium and aluminium precursor results a change in the lattice parameters. Li and Al ions appear to enhance the a-axis orientation and c-axis orientation of pure ZnO films, respectively. Field emission scanning electron micrographs of lithium-modified ZnO film indicate the presence of nanoneedles, while nanorods are observed in case of aluminium-modified ZnO film. The electrical resistance measurements of modified ZnO films also show variation in resistance as compared to pure ZnO film. Pure and Al-modified films of ZnO are sensitive to ammonia at room temperature, while Al-modified ZnO film is found to be more sensitive with 99% of response at 250 ppm.     

外电场极化对纳米氧化锌拉曼活性及气敏性能的影响

采用沉淀法制备了纳米氧化锌粒子,着重对其进行了不同条件(电场强度、极化温度)下的外电场极化处理.以X射线衍射仪和拉曼光谱仪对产物的结构、拉曼位移等进行了表征.测试了氧化锌极化产物在乙醇、丙酮气体中的气敏性能,研究了外电场效应对纳米氧化锌拉曼光谱和气敏性能的影响机制.结果表明,纳米氧化锌样品在外电场中存在着极化电场强度和温度的阈值,当电场强度和温度分别大于9375 V·cm~(-1)和150℃时,纳米氧化锌试片出现明显的漏电现象,极化效应显著降低并消失.在电场强度和温度阈值范围内,外电场极化作用能够导致氧化锌437 cm~(-1)处的拉曼特征峰强度明显降低.随外电场强度和极化温度增加,纳米氧化锌元件在丙酮气体中的灵敏度逐渐升高,在乙醇气体中的灵敏度逐渐降低,即外电场极化可以有效调控纳米氧化锌的气敏选择性.     

氧分压对PLD制备ZnO薄膜结构和发光性质的影响

采用脉冲激光沉积(PLD)技术,在Si(100)衬底上制备出高度c轴取向的ZnO薄膜。通过X射线衍射(XRD)谱,扫描电镜(SEM)和室温光致发光(PL)光谱的测量,研究了生长气氛压强的改变对薄膜结构和光致发光的影响。实验结果表明,当氧压从10Pa升高到100Pa时ZnO(002)衍射峰的半峰全宽(FWHM)增大。可以认为这是由于较高的氧压下,到达衬底表面的离子动能减小。这样部分离子没有足够的能量迁移到生长较快的(002)面,c轴取向变差,导致(002)衍射峰的强度降低,半峰全宽增大。随着氧压增大,紫外发光强度增强。这可能是氧压变大,薄膜的化学配比升高,说明化学配比对UV发光的影响要大于薄膜微结构的影响。改变氧气压强对薄膜的表面形貌也有较大的影响。     

钼掺杂氧化锌薄膜的结构、光学和表面等离子体特性研究

室温下,通过直流磁控反应溅射在石英衬底上制备一系列钼掺杂氧化锌薄膜。分别采用X射线衍射(XRD)、原子力显微镜(AFM)、分光光度计及拉曼光谱仪研究了钼掺杂浓度对氧化锌薄膜结构、表面形貌、光学性能和表面等离子体特性的影响。XRD测试结果表明,零掺杂氧化锌薄膜结晶良好,呈c轴择优取向,掺杂后薄膜缺陷增多,结晶质量下降,当掺杂浓度达到3.93 Wt%时,薄膜由c轴择优取向的晶态转变为非晶态。AFM测试结果表明非晶态掺钼氧化锌薄膜表面光滑,粗糙度最低可达489 pm。透射光谱表明所有薄膜样品在可见光范围(400～760 nm)平均透过率均达到80%,禁带宽度随着掺杂浓度的提高从3.28 eV单调增加至3.60 eV。吸收光谱表明氧化锌薄膜表面等离子体共振吸收峰随钼掺杂量的增大发生蓝移,而拉曼光谱表明Mo重掺杂时ZnO薄膜表面拉曼散射信号强度显著降低。通过Mo掺杂获得非晶态氧化锌薄膜,拓宽了氧化锌薄膜材料的应用领域,同时研究了Mo掺杂浓度对氧化锌薄膜表面等离子体的调控作用,这对制备氧化锌基光子器件具有重要参考价值。