Influence of Ⅴ/Ⅲ ratio on the structural and photoluminescence properties of In0.52AlAs/In0.53GaAs metamorphic high electron mobility transistor grown by molecular beam epitaxy

A series of metamorphic high electron mobility transistors （MMHEMTs） with different Ⅴ/Ⅲ flux ratios are grown on CaAs （001） substrates by molecular beam epitaxy （MBE）. The samples are analysed by using atomic force microscopy （AFM）, Hall measurement, and low temperature photoluminescence （PL）. The optimum Ⅴ/Ⅲ ratio in a range from 15 to 60 for the growth of MMHEMTs is found to be around 40. At this ratio, the root mean square （RMS） roughness of the material is only 2.02 nm; a room-temperature mobility and a sheet electron density are obtained to be 10610.0cm^2/（V.s） and 3.26×10^12cm^-2 respectively. These results are equivalent to those obtained for the same structure grown on InP substrate. There are two peaks in the PL spectrum of the structure, corresponding to two sub-energy levels of the In0.53Ga0.47As quantum well. It is found that the photoluminescence intensities of the two peaks vary with the Ⅴ/Ⅲ ratio, for which the reasons are discussed.     

InAs nanostructures on InP (001) substrate with the insertion of a superthin AlAs layer

An AlAs layer of two or three monolayers was inserted beneath the strained InAs layer in the fabrication of InAs nanostructure on the In_0.53Ga_0.47As and In_0.52Al_0.48As buffer layer lattice-matched to InP(001) substrate using molecular beam epitaxy. The effects of AlAs insertion on the InAs nanostructures were investigated and discussed.      

Growth of Mn5Ge3 ultrathin film on Ge（111）

The growth of Mn5Ge3 ultrathin films with different thicknesses, prepared by solid phase epitaxy, is studied. The results of scanning tunnelling microscopy and low energy electron diffraction studies show that the film can be formed and it is terminated with a （√3 × √3） R30° surface reconstruction when the thickness of Mn exceeds 3 monolayers. The magnetic properties show that the Curie temperature is about 300 K and the T^2-dependent behaviour is observed to remain up to 220 K.     

MBE生长的In_(1-x-y)Ga_xAl_yAs/InP四元混晶的拉曼散射

ＭＢＥ生长的Ｉｎ１－ｘ－ｙＧａｘＡｌｙＡｓ／ＩｎＰ四元混晶的拉曼散射韩和相汪兆平李国华徐士杰刘南竹朱作明（中国科学院半导体研究所半导体超晶格国家重点实验室北京１０００８３）ＯｐｔｉｃａｌＰｈｏｎｏｎＲａｍａｎＳｃａｔｅｒｉｎｇｆｒｏｍＩｎ１－ｘ－ｙＧ...     

Formation of high density TiN nanocrystals and its application in non-volatile memories

Non-volatile memory based on TiN nanocrystal （TiN-NC） charge storage nodes embedded in SiO2 has been fabricated and its electrical properties have been measured. It was found that the density and size distribution of TiN-NCs can be controlled by annealing temperature. The formation of well separated crystalline TiN nano-dots with an average size of 5 nm is confirmed by transmission electron microscopy and x-ray diffraction, x-ray photoelectron spectroscopy confirms the existence of a transition layer of TiNxOy/SiON oxide between TiN-NC and SiO2, which reduces the barrier height of tunnel oxide and thereby enhances programming/erasing speed. The memory device shows a memory window of 2.5V and an endurance cycle throughout 10^5. Its charging mechanism, which is interpreted from the analysis of programming speed （dVth/dt） and the gate leakage versus voltage characteristics （Ig vs Vg）, has been explained by direct tunnelling for tunnel oxide and Fowler Nordheim tunnelling for control oxide at programming voltages lower than 9V, and by Fowler-Nordheim tunnelling for both the oxides at programming voltages higher than 9V.     

Deceleration of a continuous-wave （CW） molecular beam with a single quasi-CW semi-Gaussian laser beam

We propose a promising scheme to decelerate a CW molecular beam by using a red-detuned quasi-cw semi-Gaussian laser beam （SGB）. We study the dynamical process of the deceleration for a CW deuterated ammonia （ND3） molecular beam by Monte-Carlo simulation method. Our study shows that we can obtain a ND3 molecular beam with a relative average kinetic energy loss of about 10% and a relative output molecular number of more than 90% by using a single quasi-cw SGB with a power of 1.5kW and a maximum optical well depth of 7.33mK.     

Molecular beam epitaxy growth and characterization of self-assembled InAs quantum dots on (1 0 0) InAlAs/InP substrates

Self-assembled InAs quantum dots (QDs) on In_0.52Al_0.48As layer lattice matched to (1 0 0) InP substrates have been grown by molecular beam epitaxy (MBE) and evaluated by transmission electron microscopy (TEM) and photoluminescence (PL). TEM observations indicate that defect-free InAs QDs can be grown to obtain emissions over the technologically important 1.3–1.55 μm region. The PL peak positions for the QDs shift to low energy as the InAs coverage increases, corresponding to increase in QD size. The room temperature PL peak at 1.58 μm was observed from defect-free InAs QDs with average dot height of 3.6 nm.     

A Small Signal Equivalent Circuit Model for Resonant Tunnelling Diode

We report a resonant tunnelling diode （RTD） small signal equivalent circuit model consisting of quantum capacitance and quantum inductance. The model is verified through the actual InAs/In0.53Ga0.47As/AlAs RTD fabricated on an InP substrate. Model parameters are extracted by fitting the equivalent circuit model with ac measurement data in three different regions of RTD current-voltage （I-V） characteristics. The electron lifetime, representing the average time that the carriers remain in the quasibound states during the tunnelling process, is also calculated to be 2.09ps.     

Homogeneity analysis of ion-implanted resonant tunnelling diodes for applications in digital logic circuits

A planar process for molecular beam epitaxy grown resonant tunnelling diodes (RTDs) in the GaAs/AlAs material system is presented and analysed with respect to the homogeneity of the diodes. The results can be correlated with a parameter sensitivity study based on quantum mechanical transport simulations. The homogeneity analysis reveals that our concept provides sufficient precision to fabricate RTDs suitable for application in robust digital logic circuits.     

Single crystalline boron carbide nanobelts: synthesis and characterization

This paper reports that the large-scale single crystalline boron carbide nanobelts have been fabricated through a simple carbothermal reduction method with B/B2O3/C/Fe powder as precursors at 1100℃. Transmission electron microscopy and selected area electron diffraction characterizations show that the boron carbide nanobelt has a B4C rhomb-centred hexagonal structure with good crystallization. Electron energy loss spectroscopy analysis indicates that the nanobelt contains only B and C, and the atomic ratio of B to C is close to 4：1. High resolution transmission electron microscopy results show that the preferential growth direction of the nanobelt is [101]. A possible growth mechanism is also discussed.     

Effect of magnetic field on the spin-Peierls transition in single-crystal CuGeO

This paper reports that high quality CuGeO3 single crystals were successfully grown by floating-zone technique and the magnetic property was studied. The temperature dependence of magnetic susceptibility below the spin-Peierls （SP） transition temperature （Tsp） under magnetic fields applying along both the a- and c-axis direction can be fitted well by a model of noninteracting dimmers. The spin gap derived from the fitting is consistent with other reports. There is a very weak anisotropy in the fitting parameters for different directions, which should be expected from a SP system. A small upturn in susceptibility at low temperature due to paramagnetic impurities and/or defects can be observed. A suppression of the upturn by magnetic field is first discovered in this system and the possible origins for this suppression are discussed.     

Extraction of optical constants and thickness of nanometre scale TiO2 film

TiOTiO2 薄膜 沉积物 磁电管喷射系统 X射线 发射光谱TiO₂ thin films, pointwise constrained optimization approach, constrained nonlinear programming, optical constants, parameters extractionProject supported by Shanghai Municipal Commission for Science and Technology (Grant No 03DZ14025) and National Basic Research Program of China (Grant No 2006CB300406).3/4/2005 12:00:00 AM2005-03-042005-07-28TiO2 thin films were deposited on glass substrates by sputtering in a conventional rf magnetron sputtering system. X-ray diffraction pattern and transmission spectrum were measured. The curves of refraction index and extinction coefficient distributions as well as the thickness of films calculated from transmission spectrum were obtained. The optimization problem was also solved using a method based on a constrained nonlinear programming algorithm.     

Re-research on the size of proto-neutron star in core-collapse supernova

The electron capture timescale may be shorter than hydrodynamic timescale in inner iron core of core-collapse supernova according to a recent new idea. Based on the new idea, this paper carries out a numerical simulation on supernova explosion for the progenitor model Ws15M. The numerical result shows that the size of proto-neutron star has a significant change （decrease about 20%）, which may affects the propagation of the shock wave and the final explosion energy.     

First-principles investigation of BAs and BxGa1-xAs alloys

First-principles investigation of BAs and BxGa1-xAs alloys Using first-principles calculations in the generalized gradient approximation, the electronic properties of BAs and BxGa1-xAs alloys are studied. At the Brillouin-zone centre, the lowest conduction band is the three-degenerate p-like Г15c state rather than s-like Г1c state, and the conduction band minimum （CBM） is along the A line between the Г and X points-at approximately 11/14（1,0,0）2π/a. With boron content at 0%-18.75%, BxGa1-xAs alloys have a small （2.6 eV） and relatively composition-independent band-gap bowing parameter, the band-gap increases monotonically by -18meV/B% with increasing boron content. In addition, the formation enthalpies of mixing for BxGa1-xAs alloys with boron content at 6.25% and 12.5% are calculated, and the large formation enthalpies may explain the difficulty in alloying boron to GaAs.     

High sensitivity Hall devices with AlSb/InAs quantum well structures

AlSb/InAs quantum well (QW) structures and InAs films on GaAs (001) substrates were grown by molecular beam epitaxy (MBE). We investigated the dependence of electron mobility and two-dimensional electron gas (2DEG) concentration on the thickness of an InAs channel. It is found that electron mobility as high as 19050 cm2·V-1·s-1 has been achieved for an InAs channel of 22.5 nm. The Hall devices with high sensitivity and good temperature stability were fabricated based on the AlSb/InAs QW structures. Their sensitivity is markedly superior to Hall devices of InAs films.     

Dependence of current-voltage characteristics of pseudomorphic AlAs/In0.53a0.47s/InAs resonant tunneling diodes on quantum well widths

This paper studies the dependence of I-V characteristics on quantum well widths in AlAs/In_0.53Ga_0.47As and AlAs/In_0.53Ga_0.47As/InAs resonant tunneling structures grown on InP substrates. It shows that the peak and the valley current density in the negative differential resistance region are closely related with quantum well width. The measured peak current density, valley current densities and peak-to-valley current ratio of resonant tunneling diodes are continually decreasing with increasing well width.     

InAs SELF-ASSEMBLED NANOSTRUCTURES GROWN ON InP(001)

The 6-period stacked layers of self-assembled InAs quasi-quantum wires(qQWRs) and quantum dots(QDs) embedded into InAlAs on InP(001) substrates have been prepared by solid molecular beam epitaxy. The structures are characterized by atomic force microscopy(AFM) and transmission electron microscopy(TEM). From AFM we have observed for the first time that InAs qQWRs and QDs coexist, and we explained this phenomenon from the view of the energy related to the islands. Cross-sectional TEM shows that InAs qQWRs are vertically aligned every other layer along the growth direction [001], which disagrees with conventional vertical self-alignment of InAs QDs on GaAs substrate.     

高灵敏度Sb基量子阱2DEG的霍尔器件

用分子束外延技术将高灵敏度的InAs/AlSb量子阱结构的Hall器件赝配生长在GaAs衬底上。设计了由双δ掺杂构成的Hall器件的新结构,有效地提高了器件的面电子浓度。与传统的没有掺杂的InAs/AlSb量子阱结构的Hall器件相比,室温下器件电子迁移率从15 000 cm²·V^-1·s^-1 提高到16 000 cm²·V^-1·s^-1。AFM测试表明材料有好的表面形态和结晶质量。从77 K 到300 K对Hall器件进行霍尔测试,结果显示器件不同温度范围有不同散射机构。双δ掺杂结构形成高灵敏度、高二维电子气（2DEG）浓度的InAs/AlSb异质结Hall器件具有广阔的应用前景。     

Single-well resonant-tunneling diode heterostructures based on In0.53Ga0.47As/AlAs/InP with the peak-to-valley current ratio of 22:1 at room temperature

Current-voltage (I–V) characteristics of resonant-tunneling diode In_0.53Ga_0.47As/AlAs/InP structures are studied at 300 and 77 K. The peak-to-valley current ratios were determined as 22:1 and 44:1 at temperatures of 300 and 77 K, respectively, which correspond to the maximum values for InGaAs/AlAs/InP heterostructures without an additional InAs layer of a quantum subwell in their configuration.     

Electrical transport in superlattices containing InAs quantum dots in GaAs and InP

Selectively-doped heterostructures based on both GaAs and InP containing several atomic layers coverage of InAs as both strained 2D and partially relaxed 3D (quantum dot) have been grown by gas source molecular beam epitaxy and the transport properties have been investigated. We show that while coherently strained InAs in 2D layers results in increased electron mobilities, the formation of 3D quantum dots appear to trap electrons and decrease significantly the mobility of those remaining. The degree of trapping is dependent on the size and density of the dots.