带旁通的管道中的声能流及传声损失Ⅱ：实验研究

实验证实了具有不同的旁通管长度及旁通面积的管道中传声损失及声能流的理论分析结果；对于单频噪声，三分之一倍频噪声及白噪声均有较好的降噪量，且降噪频带较宽。本文提出的“平均法”处理实验数据比原有的“三点法”好。     

阻抗复合消声器声学性能有限元预测方法及分析

为计算和分析具有复杂结构的阻抗复合式消声器的宽频消声性能,建立了一种高效声学有限元方法,给出了不同边界条件下的边界积分处理细节,得到有限元全局系数矩阵表达式,设计出计算程序框架以实现这些算法,其求解规模和计算速度与商业软件相比有优势。为计算阻抗复合式消声器的传递损失,通过阻抗管测量和数据拟合得到了吸声材料声学特性的经验公式。计算和测量了两通穿孔阻抗复合式消声器的传递损失,二者良好的吻合验证了声学有限元方法和计算程序的正确性。研究表明,插管长度影响消声器在中高频段的消声特性,右侧隔板上穿孔会消除共振峰,中高频消声性能随着出口管穿孔率的增加而提升。      

军用运输机机舱有源消声实验系统的设计与实现

为验证有源消声技术在军用运输机机舱低频噪声消除方面的有效性,设计和实现了一套机舱有源消声实验系统。采用“激振器+舱壁板”方式实现了飞机螺旋桨对机舱诱导噪声的声源模拟,设计了基于前馈控制结构的自适应有源噪声控制系统,构建了基于FX-LMS算法的自适应消声控制器,采用监测麦克风组对舱内空间的消声效果进行监测。实验结果验证了自适应有源噪声控制技术在军用飞机舱室消声降噪领域的有效性,并表明初、次级声源间距对自适应有源消声系统的消声效果具有重要的影响。     

流动管道内利用旁通管道反声降噪研究

降低流动管道噪声在工程上是非常有用的。本文应用线性声学理论将无流动时旁通管道反声降噪方法推广到具有流动的情况，进行了数值计算和实验研究。数值工作包括建立相应的声学关系和管道分叉点连接条件；计算了多种噪声源传声损失频率特性，并讨论了主要参数对反声的影响。实验研究是对单段旁通管道有吸声尖劈的情况下进行的，实验时采用不同的噪声源和不同的流速，测量结果与理论计算符合良好。PACS数43．20     

消声管道声学性能计算的二维等几何有限元方法及应用

将等几何有限元方法应用于消声管道的声学性能计算,使用二维等几何有限元方法求解管道截面的声学特征值,考虑了存在穿孔边界和吸声材料边界的情况,进而使用特征值计算消声管道的传递损失。对包覆式消声管道进行传递损失的计算,结果与二维有限元方法吻合较好.对圆形截面的特征值计算结果表明,在计算量相同的情况下,等几何有限元方法取得了比传统有限元方法更好的计算精度.在不同结构参数条件下对消声管道的声学性能进行计算,结果与三维数值方法吻合良好。方法能够在宽频范围内较好地预测消声管道的传递损失。      

水介质管路弹性背腔微穿孔消声器的传递损失特性

为抑制水介质管路系统低频噪声,兼顾结构的紧凑性,提出弹性背腔微穿孔管路消声结构,弹性管壁为橡胶帘线复合材料,并推导了传递损失的数值解法。首先,基于Biot-Allard多孔弹性理论,将弹性微穿孔板等效为弹性多孔材料;然后,利用双尺度法建立帘布的周期性代表单元,求得其刚度矩阵;接着,基于分层理论,建立弹性管壁的多层复合材料模型,并与内部声场耦合计算,得到弹性背腔微穿孔管路消声器的传递损失。在水介质驻波管中,利用双声源法测量弹性背腔微穿孔管路消声器样机的传递损失曲线,并与扩张式管路消声器和刚性背腔微穿孔管路消声器进行对比,理论结果与试验结果吻合良好。研究表明,弹性背腔微穿孔管路消声器属于反射耗散复合式消声器,具有低频域、宽频带的消声特性。样机B2在40~300 Hz和40~1200 Hz频段内的传递损失分别为36 dB和30 dB,而相同尺寸扩张式消声器在对应频段的传递损失分别为7 dB和11 dB。      

具有流动和侧向Helmholtz共振器的驻波管内声场研究Ⅱ.实验验证及结果讨论

利用建立的具有流动和侧向Helmholtz共振器的驻波管的实验装置,成功地证实了作者所作的理论分析,包括有流动驻波管和Helmholtz共振器连接处的间断条件、驻波管末端的反射条件、切向流时Helmholtz共振器声阻抗,并实验确定了末端修正系数和等效半径系数。接着,应用理论分析和实验得到的结果讨论了流动对Helmholtz共振器性能和驻波管声场的影响,结果表明,流动会降低一些消声效果,但在具有流动的驻波管中采用Helmholtz共振器仍然是一种降噪的有效方法。     

管道模态波入射下HQ管降噪机理研究

随着涡扇发动机风扇直径增大转速降低,低频噪声控制问题引发格外关注。HQ管作为一种抗性降噪结构,在低频段拥有良好的降噪效果。本文首先建立了带HQ管的管道风扇噪声数值模型,并对声传播特性进行了细致的仿真分析,获得了与前期实验数据对比一致性良好的预测结果。最后通过不同HQ管排布螺旋角下降噪效果和声模态分解结果的对比分析,对HQ管降噪机理进行了探讨,发现HQ管对模态波降噪的主要模式是模态的反射与散射,并且不同于将入射模态散射为截止模态的传统认知,将入射模态散射为不占优的可传播模态可以大幅削弱占优模态的幅值,同样具有较为明显的降噪效果。     

非对称阻抗插入管消声器的Chebyshev-变分法建模与求解

针对非对称阻抗插入管消声器三维理论建模与求解问题,提出了一种半解析变分建模和求解方法,试验及有限元结果验证了理论模型和求解结果的正确性,开展了模态频率、声压响应及传递损失等声场特性的预测分析。首先构建插入管消声器内部子声场拉格朗日泛函,基于声压与质点振速连续性条件,得到插入管消声器三维理论模型。随后,将子声场声压展开为切比雪夫-傅里叶级数组合形式,按里兹法求得消声器三维声场模态信息。搭建了消声器传递损失试验平台,进行了刚性壁面和阻抗壁面消声器传递损失测试试验,对理论模型和计算结果进行了验证。通过算例分析了壁面阻抗的大小、阻抗面积和分布形式以及插入管偏置对消声器消声性能的影响。结果表明,提出的变分建模求解方法是有效的,对消声器壁面阻抗位置和形式的合理设置可有效降低输出声压。      

一种微穿孔板消声器

本文根据马大猷教授提出的“微穿孔板吸声体精确理论”，在对微穿孔板消声器结构参数与吸声特性之间的相互影响进行了分析的基础上，设计了微穿孔板消声器并将其应用在新舟60飞机APU(辅助动力装置)降噪的实际工程中，并通过编写的噪音数据采集分析程序，对降噪效果进行了测试和分析，验证出微穿孔板消声器对消除飞机的APU的排气噪声具有良好的消声效果，平均降噪7．16dB。     

The research on semi-active muffler device of controlling the exhaust pipe’s low-frequency noise

In order to control low frequency noise in exhaust pipe, this paper puts forward a new concept of H-Q tube based semi-active muffler device. The semi-active muffler device and bench testing system have been designed and operated. Finite element simulation study on semi-active muffler and experimental study on semi-active muffler and passive muffler have been carried on. The effect of simulation and experiment are consistent. The semi-active muffler device acts well in low frequency band, especially between 50 Hz and 150 Hz. The average level of noise reduction is around 35 dB, which is much better than passive muffler. Between 150 Hz and 350 Hz, semi-active muffler has a better performance than passive muffler; above 350 Hz, it has worse performance compared with the passive muffler.     

Active control of aircraft fly-over sound transmission through an open window

This paper presents an experimental work on active control of sound transmission through a restricted opening bottom hinged window. The main goal of the work is to demonstrate the feasibility of the active technique to limit the loss of attenuation due to the aperture of windows, and its application to aircraft fly-over incident noise. The experimental window is placed in an exposed façade of a dwelling close to an airport and subject to fly-by aircraft noise. The active control is configured to cancel the pressure at the aperture using a single-input single-output feedforward adaptive system. As a result, a reduction of sound transmission is achieved with low power consumption. In global terms, an increase of almost 3 dB of transmission loss (with respect to the partially opened window insulation values) in the low frequency range (below 160 Hz and according to the National Danish Method for evaluating low frequency noise) is demonstrated, which is equivalent to a reduction of 50% in the loss of insulation caused by opening the window.     

高声强行波管装置

本文介绍飞机强度研究所小型高声强行波管的声学设计和消声降噪处理。     

对称折叠通道结构的低频通风吸声体*

为了消除或减少低频噪声,该文 提出了一种低频通风超材料吸声体,该吸声体由对称的折叠通道结构组成,具有深度亚波长、高通风空间占比和低频高效吸声的特性.通过传递矩阵方法、有限元模拟和四麦克风实验法,揭示了对称折叠通道结构通风吸声的物理机制.首先在理论上分析单个吸声体的通风吸声性能并进行了仿真模拟,在共振频率423 Hz附近,吸声系数大于0.9,通风空间占比高达40%.吸声单体的共振频率可通过改变折叠通道的长度来灵活调控,组合多个不同共振频率的吸声单体可以拓宽吸声体的有效吸声带宽.由四个吸声单体组合的通风吸声体可实现314－366 Hz频率范围内的高效声吸收(吸声系数大于0.8),且通风空间占比达到35%,而结构厚度仅为314 Hz时波长的1/10.该低频通风吸声体具有结构简单、结构强度高和容易制造等特点,在低频通风降噪领域有着潜在的应用前景．     

Sound attenuation of a periodic array of micro-perforated tube mufflers

The wave propagation in a periodic array of micro-perforated tube mufflers is investigated theoretically, numerically and experimentally. Because of the high acoustic resistance and low mass reactance due to the sub-millimeter perforation, the micro-perforated muffler can provide considerable sound attenuation of duct noise. Multiple mufflers are often used to enhance attenuation performance. When mufflers are distributed periodically in a duct, the periodic structure produces special dispersion characteristics in the overall sound transmission loss. The Bloch wave theory and the transfer matrix method are used to study the wave propagation in periodic micro-perforated tube mufflers and the dispersion characteristics of periodic micro-perforated mufflers are examined. The results predicted by the theory are compared with finite element method simulation and experimental results. The results indicate that the periodic structure can influence the performance of micro-perforated mufflers. With different periodic distances, the combination of the periodic structure and the micro-perforated tube muffler can contribute to the control of lower frequency noise with a broader frequency range or improvement of the peak transmission loss around the resonant frequency.     

Investigation on Noise Pollution Comprehensive Treatment of Distribution Transformer in Living Area

In the current paper, which deals with the noise pollution excited by distribution transformers in the living area, a comprehensive treatment scheme is put forward for the purpose of reducing the sound pressure level emitting into the environment. In accordance with the associated test standard, the sound pressure levels of distribution transformer and surrounding environment are not only tested but analyzed as well. The measurements were carried out with the frequency analysis of the 1/3 octave resolution, with the center frequencies at 125 Hz, 250 Hz, 400 Hz, and 500 Hz. As illustrated, on the basis of the measurement results, the frequency of noise at 500 Hz of distribution transformer causes the major noise pollution in the surrounding environment. This measurement result is in line with the noise frequency characteristics of distribution transformer. There are two transmission routes of noise: i) the noise excited by distribution transformer transmits by means of the wall of distribution room, and ii) part of noise spreads through the ground of distribution room. Accordingly, acoustic shield and vibration isolation device are applied for the reduction of the low frequency noise emitted through the above two paths. Aimed at applying the appropriate acoustic material and vibration mounting, the evaluation of the noise reduction and vibration absorption is carried out in accordance with the sound and vibration insulation theory. Following the noise treatment, the transformer and environment noise are measured again. The corresponding findings shed light on the fact that the sound level satisfied the requirement of limits of the ordinance. The proposed noise treatment scheme can be applied to the existing power distribution facilities for controlling the sound levels that reach a point where it is comparatively more unobjectionable.     

Low frequency sound insulation using stiffness control with honeycomb panels

A new honeycomb core design has been used to increase the stiffness of the panel and applied to improve the noise transmission loss at frequencies between 100 and 200 Hz. A model is presented to predict the transmission loss of the honeycomb panels based on the structural modal parameters. A new test specimen with fiber reinforced plastic cores and face sheets had been used to investigate the effect of stiffness and damping on noise transmission loss. The measurements of noise transmission loss have been compared with data for common structural panels. The results show that the new core fabrication techniques using moulding to improve the noise transmission are effective. In comparison to a cement panel of the same mass, the honeycomb panels have higher TL at low frequencies between 100 and 200 Hz due to higher stiffness and damping. The honeycomb panels have more significant vibration responses above 500 Hz but these are limited by damping.     

轻卡进气管的结构优化及其声学性能

为有效降低轻卡进气管的噪声，首先通过原始进气管的噪声实验，测试得出噪声的主要贡献频率，结合管道的布置情况，进行了消声器(谐振腔)的设计，进而完成对进气管的优化设计；通过专业声学分析软件LMS Virtual.lab对优化前后的进气管进行声学性能的模拟研究，得出了谐振腔对声场的具体影响；通过噪声实验，分析出加装谐振腔的进气管相比于原始进气管的降噪效果。研究结果表明：在所研究的进气管噪声的主要贡献频率下(即125 Hz、180 Hz、465 Hz、640 Hz)，加装谐振腔后，传递损失均能得到有效增加；在怠速工况和加速工况下，优化后的进气管噪声值均能满足限定值。因此，通过添加谐振腔来优化进气管可以达到了较好的降噪效果。该研究可为汽车进气管降噪元件的优化设计提供一定的指导。     

基于低频吸声超构材料的复合消声器研究*

针对管道内低频噪声难以抑制的问题，本文基于亥姆霍兹共振腔（HR）阵列吸声板和穿孔管消声器组合，设计了一种复合式宽带消声器。首先利用有限元法仿真分析传统穿孔管消声器，发现中低频消声能力较差，通过嵌入HR阵列吸声板吸收中低频噪声。采用仿真与实验的方式研究吸声板的声学性能：在400-1000 Hz频段内的平均吸声系数达到了0.88。然后对复合式消声器进行数值模拟及3D打印阻抗管实验测试对比：复合式消声器在400-1718Hz频率范围内的平均传递损失为18.15 dB ，最终实现了管道内全频带噪声有效控制。