电化学方法制备ZnO纳米颗粒掺杂类金刚石薄膜及其场发射性能研究

采用液相电化学沉积技术制备了ZnO纳米颗粒掺杂的类金刚石(DLC)薄膜, 研究了ZnO纳米颗粒掺杂对DLC薄膜场发射性能的影响. 利用X射线光电子能谱、透射电子显微镜、Raman光谱以及原子力显微镜分别对薄膜的化学组成、 微观结构和表面形貌进行了表征. 结果表明: 薄膜中的ZnO纳米颗粒具有纤锌矿结构, 其含量随着电解液中Zn源的增加而增加. ZnO纳米颗粒掺杂增强了DLC薄膜的石墨化和表面粗糙度. 场发射测试表明, ZnO纳米颗粒掺杂能提高DLC薄膜的场发射性能, 其中Zn与Zn+C的原子比为10.3%的样品在外加电场强度为20.7 V/μm时电流密度达到了1 mA/cm². 薄膜场发射性能的提高归因于ZnO掺杂引起的表面粗糙度和DLC薄膜石墨化程度的增加.     

Al纳米颗粒表面等离激元对ZnO光致发光增强的研究

基于聚苯乙烯球自组装法,在P型氮化镓(P-GaN)衬底上制备了有序致密的掩模板;采用热蒸发法在该模板上沉积金属Al薄膜,通过甲苯溶液去除聚苯乙烯球,得到了金属Al纳米颗粒阵列;采用原子层沉积法,在Al纳米颗粒阵列表面依次沉积氧化铝(Al_2O_3)和氧化锌(ZnO).通过测试Al纳米颗粒阵列的消光谱以及ZnO薄膜的光致发光谱,研究了Al纳米颗粒表面等离激元与ZnO薄膜激子之间的耦合效应.实验结果表明:引入Al纳米颗粒后,在约380 nm位置附近的ZnO近带边发光峰积分强度增强了1.91倍.对Al纳米颗粒表面等离激元增强ZnO光致发光的机理进行探讨.     

一种新的制备ZnO纳米粒子的方法--阴极电沉积法

用阴极电沉积法制备高质量ZnO纳米薄膜，电沉积采用含有不同浓度的ZnCl2的非水二甲基亚砜溶液做电解液，室温下恒流沉积，得到纳米ZnO薄膜。研究了ZnCl2浓度对薄膜结构和光学性质的影响。沉积薄膜的ZnO粒径尺寸分别为9．8，10．4，14．5nm。随着ZnCl2浓度的增加而增大。薄膜的可见光致发光谱以紫外的自由激子发射为主。研究表明：以浓度为0.03mol/L的ZnCl2电解液制备的ZnO薄膜光学性质最好。     

银纳米颗粒/多孔硅复合材料的制备与气敏性能研究

采用双槽电化学腐蚀法以电阻率为10-15 Ω·cm的p型<100>晶向的单晶硅片制备了孔径约为1.5 μm, 孔深约为15-20 μm的p型多孔硅, 并以此多孔硅作为基底采用无电沉积法通过调控沉积时间在其表面沉积了不同厚度的银纳米颗粒薄膜. 采用扫描电子显微镜和X 射线衍射仪表征了银纳米颗粒/多孔硅复合材料的形貌和微观结构, 结果表明银纳米颗粒较均匀的分布于多孔硅的表面上且沉积时间对产物的形貌有重要影响. 采用静态配气法在室温下研究了银纳米颗粒/多孔硅复合材料对NH₃的气敏性能. 气敏测试结果表明沉积时间对产物的气敏性能影响较大. 当沉积时间较短时, 适量银纳米颗粒掺杂的多孔硅复合材料由于其较高的比表面积以及特殊的形貌和结构, 对NH₃气体表现出较高的灵敏度、优良的响应/恢复性能. 室温下, 其对50 ppm 的NH₃气体的气敏灵敏度可以达到5.8左右.     

脉冲激光沉积法制备的ZnO薄膜的低阈值电抽运紫外随机激射

分别采用直流反应溅射法和脉冲激光沉积法在硅衬底上沉积ZnO薄膜, 用X射线衍射、扫描电镜、光致发光谱等手段对两种方法沉积的ZnO薄膜的结晶状态、 表面形貌和光致发光等进行了表征. 进一步对比研究了以上述两种方法制备的ZnO薄膜作为发光层的金属-绝缘体-半导体结构器件的电抽运紫外随机激射. 结果表明, 与以溅射法制备的ZnO薄膜作为发光层的器件相比, 以脉冲激光沉积法制备的ZnO薄膜为发光层的器件具有更低的紫外光随机激射阈值电流和更高的输出光功率. 这是由于脉冲激光沉积法制备的ZnO薄膜中的缺陷更少, 从而显著地减少了紫外光在光散射过程中的光损耗. 关键词： 随机激射 ZnO薄膜 脉冲激光沉积 溅射     

透明导电ZnO薄膜的电化学制备及性能研究

以修饰的ITO玻璃为衬底,以不同浓度Zn(NO3)2.6H2O作为电解质溶液,采用阴极恒流沉积法制备了不同纳米结构的ZnO薄膜。用X射线衍射(XRD)、场发射扫描电镜(FE-SEM)、四探针仪(RTS-8)、紫外-可见(UV-Vis)光谱仪、循环伏安等分别表征薄膜的晶相、形貌和厚度、方块电阻、紫外-可见光透过率和氧化还原电位。结果表明:低浓度溶液沉积得到的c轴取向1D ZnO纳米柱和高浓度溶液沉积得到的致密2D六方ZnO纳米片在可见光范围(400～900 nm)的透过率均可高达85%以上,方块电阻约为14.5Ω/□。两种结构的氧化还原电位有显著区别,纳米柱的为-0.54 V(vs.SCE),而纳米片的为-0.72 V(vs.SCE),说明纳米片状的ZnO薄膜具有更为良好的化学稳定性。     

纳米VO2/ZnO复合薄膜的热致变色特性研究

为提高VO₂薄膜的热致变色性能,采用纳米结构和复合结构二者相结合的方法,通过磁控溅射技术先在玻璃衬底上制备高(002)取向ZnO薄膜,再在ZnO层上室温沉积钒金属薄膜,最后经热氧化处理获得纳米结构VO₂/ZnO复合薄膜.利用变温拉曼光谱观察分析了VO₂/ZnO薄膜相变前后的晶格畸变和键态的演变过程,讨论了薄膜的结构与热致红外开关特性和相变温度的内在关系.结果显示,与相同条件获得的同厚度的单层VO₂薄膜相比,纳米VO关键词： ZnO 2')" href="#">VO₂ 纳米复合薄膜 热致变色 拉曼光谱     

高质量纳米ZnO薄膜的光致发光特性研究

报道了利用低压-金属有机物化学气相沉积技术生长纳米ZnS薄膜，然后，将ZnS薄膜在氧气中于800℃温度下进行热氧化制备高质量纳米ZnO薄膜.x射线衍射结果表明，纳米ZnO薄膜具有六角纤锌矿多晶结构.室温下观察到一束强的紫外(3.26 eV) 光致发光和很弱的深能级发射.根据激子峰的半高宽度与温度的关系确定了激子-纵向光学声子（LO）的耦合强度（ГLO）.由于量子限域效应使ГLO减少较多. 关键词： 光致发光 热氧化 激子 纳米ZnO薄膜     

包埋Pt纳米粒子对金属-半导体-金属结构ZnO紫外光电探测器性能的影响

利用射频磁控溅射设备制备ZnO薄膜, 最终制备ZnO/Pt纳米粒子/ZnO 结构的金属-半导体-金属型紫外光电探测器. 研究了Pt纳米粒子处在ZnO薄膜层中的不同深度对金属-半导体-金属型紫外光电探测器响应性能的影响. 结果表明, 探测器的响应度随着Pt纳米粒子在ZnO薄膜层中所处深度的增大而升高. 在60 V偏压下, 包埋Pt最深的探测器在波长365 nm处取得响应度最大值1.4 A·W^-1, 包埋有Pt探测器的响应度最大值为无Pt 纳米粒子探测器响应度最大值的7倍. 结合对ZnO薄膜表面的表征及探测器各项性能的测试, 得出包埋Pt纳米粒子增强器件的响应性能可归因于表面等离子体增强散射.     

氮对类金刚石薄膜的微观结构内应力与附着力的影响

采用原子力显微镜(AFM)、俄歇电子能谱(AES)和显微压痕分析等手段对射频等离子体增强化学气相沉积法制备的掺氮类金刚石(DLC：N)薄膜的微观结构和力学性能进行了研究.结果表明,随着含氮量的增加,DLC薄膜的AFM表面形貌中出现了几十纳米的颗粒,原子侧向力显微镜和AES分析表明这种纳米颗粒是x大于0.126的非晶氮化碳CN_x结构.这种非晶DLC/CN_x的纳米复合结构,减小了薄膜的内应力,从而提高了薄膜与衬底的附着力. 关键词： 类金刚石碳膜 微观结构 附着特性     

Effects of polyethylenimine on morphology and property of ZnO films grown in aqueous solutions

Morphologies and properties of well-aligned ZnO films were controlled using zinc nitrate-hexamethylenetetramine aqueous solutions with the addition of polyethylenimine as a surfactant. Porous and dense ZnO films were fabricated with and without polyethylenimine, respectively. The addition of polyethylenimine proceeded to form porous ZnO whiskers film by preferential adsorption to nonpolar crystal faces and modifications of the surface free energy and growth rate. Dense ZnO film showed high transmittance of 80%, and low intensity of fluorescence and photo-induced current. Porous ZnO whiskers film showed low transmittance of 70%, while high intensity of fluorescence and high photo-induced current were detected because the porous ZnO nanowhisker film possessed a large interior surface area which can capture large amounts of DNA molecules labeled with dye molecules on the surface of ZnO crystals. High performance dye-sensitized sensors can be produced using ZnO whisker films prepared from an aqueous solution.     

Room-temperature deposition of crystalline patterned ZnO films by confined dewetting lithography

In this work patterned ZnO films were prepared at room-temperature by deposition of ∼5 nm size ZnO nanoparticles using confined dewetting lithography, a process which induces their assembly, by drying a drop of ZnO colloidal dispersion between a floating template and the substrate. Crystalline ZnO nanoparticles exhibit a strong visible (525 nm) light emission upon UV excitation (λ = 350 nm). The resulting films were characterized by scanning electron microscopy (SEM) and atomic force microscope (AFM). The method described herein presents a simple and low cost method to prepare crystalline ZnO films with geometric patterns without additional annealing. Such transparent conducting films are attractive for applications like light emitting diodes (LEDs). As the process is carried out at room temperature, the patterned crystalline ZnO films can even be deposited on flexible substrates.     

Temperature and concentration dependences of the photoluminescence of MEH-PPV polymer composite films with ZnO nanoparticles

The absorption and photoluminescence (PL) spectra of MEH-PPV: ZnO composite films have been investigated at different concentrations of ZnO nanoparticles and at different temperatures (in the case of PL). It has been shown that, at 297 K, with increasing concentration of ZnO nanoparticles in the composite, the intensity of the PL lines of MEH-PPV decreases, whereas the intensity of the PL lines of ZnO increases. At a relatively low concentration of ZnO nanoparticles, a decrease in the temperature leads to an increase in the intensity of PL lines associated with MEH-PPV and ZnO, whereas at higher concentrations of ZnO nanoparticles, the intensity of these lines decreases. This is accompanied by a slight shift in the maximum of the PL toward the infrared (IR) region and a narrowing of the PL line of MEH-PPV with a decrease in the temperature and with an increase in the ZnO concentration. The mechanism of energy transfer in composite systems consisting of a polymer and inorganic nanoparticles that can be responsible for the observed effects has been discussed.     

A study on the optical and electrical properties of direct-patternable ZnO films incorporated various contents of Pt nanoparticles

Platinum nanoparticles were synthesized by the methanol reduction method, and their size was controlled to 3 nm on average using PVP [poly(N-vinyl-2-pyrrolidon)] as a protecting unit. Various contents of Pt nanoparticles were incorporated into ZnO solutions which were synthesized by a sol-gel process. ZnO films with Pt nanoparticles of various content were annealed at 500 °C and 600 °C for 1 h. The crystallinity increased with the annealing temperature and also slightly with the content of Pt nanoparticles. The sheet resistance of ZnO films decreased with the incorporation of Pt nanoparticles, however the decreasing behavior was not maintained with increasing content of Pt nanoparticles. A shift of valence band maximum energy of ZnO film with Pt nanoparticles to higher energy was also observed due to electron transfer from Pt nanoparticles to ZnO film. The optical transmittance was 88 ± 2% in the visible region for all the ZnO films. Well-defined 60 μm wide direct-patterned ZnO films containing Pt nanoparticles of 0.5 atomic percent could be formed without using dry etching process.     

Fabrication of ZnO nanoparticles-embedded hydrogenated diamond-like carbon films by electrochemical deposition technique

ZnO nanoparticles-embedded hydrogenated diamond-like carbon (ZnO-DLC) films have been prepared by electrochemical deposition in ambient conditions. The morphology, composition, and microstructure of the films have been investigated. The results show that the resultant films are hydrogenated diamond-like carbon films embedded with ZnO nanoparticles in wurtzite structure, and the content and size of the ZnO nanoparticles increase with increasing deposition voltage, which are confirmed by X-ray photoelectron spectroscopy (XPS), Raman, and transmission electron microscope (TEM). Furthermore, a possible mechanism used to describe the growth process of ZnO-DLC films by electrochemical deposition is also discussed.     

金纳米颗粒等离激元对不同形貌氧化锌薄膜发光性能的调控

采用化学气相沉积法制备了纳米棒状的氧化锌纳米结构薄膜和没有纳米棒的氧化锌薄膜,通过直流溅射在所制备的有纳米棒和没有纳米棒的氧化锌薄膜上淀积约3 nm厚的金纳米颗粒薄膜,研究了金纳米颗粒对不同表面形貌氧化锌薄膜的发光特性的影响。实验发现金纳米颗粒的存在使具有纳米棒的氧化锌薄膜的紫外发射增强,但使来自缺陷的可见光发射受到很大的抑制。通过比较有纳米棒和没有纳米棒的氧化锌薄膜在镀金纳米颗粒前后的发光特性,发现金表面等离激元对氧化锌发光的调控取决于氧化锌的表面形貌,纳米棒的存在更有利于金纳米颗粒等离激元调控氧化锌的发光特性。     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

Porous Silicon as an Intermediate Buffer Layer for Zinc Oxide Nanorods

Zinc thin films were deposited onto porous silicon (PSi) substrates by dc sputtering using a Zn target. These films were then annealed under flowing (6 l/min) oxygen gas environment in the furnace at 600°C for 2 h. Porous silicon is used as an intermediate layer between silicon and ZnO films and it provides a large area composed of an array of voids. The PSi samples were prepared using photoelectrochemical method on n-type silicon wafer with (111) and (100) orientation. To prepare porous structures, the samples were dipped into a mixture of HF:ethanol (1:1) for 5 min with current densities of 50 mA/cm², and subjected to external illumination with a 500 W UV lamp. The surface morphology and the nanorod structure of the ZnO films were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD). We synthesized the ZnO nanorods with diameter of 80–100 nm without any catalysts or templates. The XRD pattern confirmed that the ZnO nanorods were of polycrystalline structure. The surface-related optical properties have been investigated by photoluminescence (PL) and Raman measurements at room temperature. Micro-Raman results showed that A₁(LO) of hexagonal ZnO/Si(111) and ZnO/Si(100) have been observed at 522 cm^–1 and 530 cm^–1, respectively. PL spectra peaks are clearly visible at 366 cm^–1 and 368 cm^–1 for ZnO film grown on porous Si(111) and Si(100) substrates, respectively. The PL spectral peak position in ZnO nanorods on porous silicon is blue-shifted with respect to that in unstrained ZnO (381 nm).     

Optical Analysis of Nanocrystalline ZnO Films Coated on Porous Silicon by Radio Frequency (RF) Magnetron Sputtering

Zinc oxide thin films have been deposited onto porous silicon (PSi) substrates at high growth rates by radio frequency (RF) sputtering using a ZnO target. The advantages of the porous Si template are economical and it provides a rigid structural material. Porous silicon is applied as an intermediate layer between silicon and ZnO films and it contributed a large area composed of an array of voids. The nanoporous silicon samples were adapted by photo electrochemical (PEC) etching technique on n-type silicon wafer with (111) and (100) orientation. Micro-Raman and photoluminescence (PL) spectroscopy are powerful and non-destructive optical tools to study vibrational and optical properties of ZnO nanostructures. Both the Raman and PL measurements were also operated at room temperature. Micro-Raman results showed that the A₁(LO) of hexagonal ZnO/Si(111) and ZnO/Si(100) have been observed at around 522 and 530 cm^–1, re- spectively. PL spectra peaks are distinctly apparent at 366 and 368 cm^–1 for ZnO film grown on porous Si(111) and Si(100) substrates, respectively. The peak luminescence energy in nanocrystalline ZnO on porous silicon is blue-shifted with regard to that in bulk ZnO (381 nm). The Raman and PL spectra pointed to oxygen vacancies or Zn interstitials which are responsible for the green emission in the nanocrystalline ZnO.     

氧化锌纳米颗粒薄膜的近紫外电致发光特性研究

利用溶胶-凝胶法(sol-gel method)制备了ZnO纳米颗粒薄膜(ZnO nanoparticle film),并以此为发光层制备了结构为ITO/ZnO nanoparticle/MEH-PPV/LiF/Al的电致发光器件.通过调整器件发光层厚度,对器件的发光光谱和电学特性进行测试研究,发现该器件在一定的直流电压下可以得到以ZnO近紫外(中心波长390 nm)发光为主的电致发光光谱,显示出较好的ZnO近紫外电致发光特性.对该器件的发光机理进行了一定的研究,认为该器件的发光是基于载流子隧穿.