Near infrared to UV dielectric functions of Al doped ZnO films deposited on c-plane sapphire substrate using pulsed laser deposition

Transparent conducting polycrystalline Al-doped ZnO (AZO) films were deposited on sapphire substrates at substrate temperatures ranging from 200 to 300 °C by pulsed laser deposition (PLD). X-ray diffraction measurement shows that the crystalline quality of AZO films was improved with increased substrate temperature. The electrical and optical properties of the AZO films have been systematically studied via various experimental tools. The room-temperature micro-photoluminescence (µ-PL) spectra show a strong ultraviolet (UV) excitonic emission and weak deep-level emission, which indicate low structural defects in the films. A Raman shift of about 11 cm⁻¹ is observed for the first-order longitudinal-optical (LO) phonon peak for AZO films when compared to the LO phonon peak of bulk ZnO. The Raman spectra obtained with UV resonant excitation at room temperature show multi-phonon LO modes up to third order. Optical response due to free electrons of the AZO films was characterized in the photon energy range from 0.6 to 6.5 eV by spectroscopic ellipsometry (SE). The free electron response was expressed by a simple Drude model combined with the Cauchy model are reported.     

Growth of carbon nanofibers on aligned zinc oxide nanorods and their field emission properties

Carbon nanofibers were grown by electrodeposition technique onto aligned zinc oxide (ZnO) nanorods deposited by hybrid wet chemical route on glass substrates. X-ray diffraction traces indicated very strong peak for reflections from (0 0 2) planes of ZnO. The Raman spectra were dominated by the presence of G band at about 1597 cm⁻¹ corresponding to the E_2g tangential stretching mode of an ordered graphitic structure with sp² hybridization and a D band at about 1350 cm⁻¹ originating from disordered carbon. Fourier transformed infrared studies indicated the presence of a distinct characteristic absorption peak at ∼511 cm⁻¹ for Zn-O stretching mode. Photoluminescence spectra indicated band edge luminescence of ZnO at ∼3.146 eV along with a low intensity peak at ∼0.877 eV arising out of carbon nanofibers. Field emission properties of these films and their dependence on the CNF coverage on ZnO nanorods are reported here. The average field enhancement factor as determined from the slope of the FN plot was found to vary between 1 × 10³ and 3 × 10³. Both the values of turn-on field and threshold field for CNF/ZnO were lower than pure ZnO nanorods.     

Origin of the Raman mode at 379 cm−1 observed in ZnO thin films grown on sapphire

In this work, we present a detailed Raman scattering study to clarify the origin of the mode at 379 cm⁻¹ which is observed in Raman spectra of the ZnO films grown on c‐sapphire substrates and generally attributed to the A₁‐transverse optical (A₁‐TO) mode of ZnO. The studied ZnO films were deposited by metal‐organic chemical vapor deposition on c‐sapphire and (0001) ZnO substrates. In the z(−,−)z̄ backscattering configuration, the A₁‐TO mode is forbidden, while the 379 cm⁻¹ peak is still observed in the as‐deposited film grown on sapphire substrate. However, this mode is not observed in Raman spectra of the as deposited film grown on ZnO substrate. We suggest that the peak at 379 cm⁻¹ is the E_1g mode of the sapphire substrate which is allowed in z(−,−)z̄ backscattering configuration. The effects of annealing, the substrate and the collection cross‐section on Raman active modes were analyzed. Copyright © 2011 John Wiley & Sons, Ltd.     

Effects of rf power on surface-morphological, structural and electrical properties of aluminium-doped zinc oxide films by magnetron sputtering

Aluminium-doped zinc oxide (ZnO:Al) films were prepared by magnetron sputtering at different radio-frequency powers (P_rf) of 50, 100, 150 and 200 W. The properties of the films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), Raman microscopy, and spectrophotometry with the emphasis on the evolution of compositional, surface-morphological, optical, electrical and microstructural properties. XPS spectra showed that within the detection limit the films are chemically identical to near-stoichiometric ZnO. AFM revealed that root-mean-square roughness of the films has almost linear increase with increasing P_rf. Optical band gap E_gopt of the films increases from 3.31 to 3.51 eV when P_rf increases from 50 to 200 W. A widening E_gopt of the ZnO:Al films compared to the band gap (∼3.29 eV) of undoped ZnO films is attributed to a net result of the competition between the Burstein-Moss effect and many-body effects. An electron concentration in the films was calculated in the range of 3.73 × 10¹⁹ to 2.12 × 10²⁰ cm⁻³. Raman spectroscopy analysis indicated that well-identified peaks appear at around 439 cm⁻¹ for all samples, corresponding to the band characteristics of the wurtzite phase. Raman peaks in the range 573-579 cm⁻¹ are also observed, corresponding to the A₁ (LO) mode of ZnO.     

Effects of sic buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates

ZnO films have been grown by a sol-gel process on Si (1 1 1) substrates with and without SiC buffer layers. The influence of SiC buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates was investigated. The intensity of the E₂ (high) phonon peak in the micro-Raman spectrum of ZnO film with the SiC buffer layer is stronger than that of the sample without the SiC buffer layer, and the breadth of E₂ (high) phonon peak of ZnO film with the SiC buffer layer is narrower than that of the sample without the SiC buffer layer. These results indicated that the crystalline quality of the sample with the SiC buffer layer is better than that of the sample without the SiC buffer layer. In photoluminescence spectra, the intensity of free exciton emission from ZnO films with the SiC buffer was much stronger than that from ZnO film without the SiC buffer layer, while the intensity of deep level emission from sample with the SiC buffer layer was about half of that of sample without the SiC buffer layer. The results indicate the SiC buffer layer improves optical qualities of ZnO films on Si (1 1 1) substrates.     

As-doped p-type ZnO films grown on SiO2/Si by radio frequency magnetron sputtering

p-Type ZnO:As films with a hole concentration of 10¹⁶-10¹⁷ cm⁻³ and a mobility of 1.32-6.08 cm²/V s have been deposited on SiO₂/Si substrates by magnetron sputtering. XRD, SEM, Hall measurements are used to investigate the structural and electrical properties of the films. A p-n homojunction comprising an undoped ZnO layer and a ZnO:As layer exhibits a typical rectifying behavior. Our study demonstrates a simple method to fabricate reproducible p-type ZnO film on the SiO₂/Si substrate for the development of ZnO-based optoelectronic devices on Si-based substrates.     

Large-quantity synthesis of ZnO hollow objects by thermal evaporation: Growth mechanism, structural and optical properties

Synthesis of large-quantity uniformly distributed ZnO hollow objects, i.e. cages and spheres have been performed on Si(1 0 0) and steel alloy substrates by the direct heating of metallic zinc powder in the presence of oxygen. Extensive structural observations revealed that the formed products are crystalline ZnO with the wurtzite hexagonal phases. The Raman-active optical phonon E₂ modes, attributed to wurtzite hexagonal phase of ZnO, were observed at 437 cm⁻¹ for the products grown on both the substrates. The room-temperature photoluminescence spectra showed a broad band in the visible region with a suppressed UV emission, indicating the presence of oxygen vacancies and structural defects in the as-grown structures. Additionally, post growth annealing was also carried out to further investigate the photoluminescence properties of the as-grown products. It was observed that the formation of hollow objects consists of several stages which include the formation of Zn clusters, oxidation on the sheath and sublimation/evaporation of the Zn from the interiors, resulted in the formation of hollow objects.     

On the mixed nature of the 740 cm band in wurtzite GaN films: A polarized Raman scattering investigation

A detailed study of the polarized Raman scattering of wurtzite GaN films is presented, focusing on the nature of the band centered at 740 cm⁻¹ observed in the X(Z, Z)X configuration. The origin of this band is ascribed to the mixed contribution of the A₁ and E₁ longitudinal phonon modes coupled with the free carrier excitation. The spectral profile of the 740 cm⁻¹ Raman band has been successfully reconstructed through a linear combination of the A₁-E₁ longitudinal phonon plasmon-coupled modes, leading to a free carrier concentration in good agreement with Hall effect measurements.     

Fabrication of p-type Li-doped ZnO films by pulsed laser deposition

p-Type ZnO thin films have been realized via doping Li as acceptor by using pulsed laser deposition. In our experiment, Li₂CO₃ was used as Li precursor, and the growth temperature was varied from 400 to 600 °C in pure O₂ ambient. The Li-doped ZnO film prepared at 450 °C possessed the lowest resistivity of 34 Ω cm with a Hall mobility of 0.134 cm² V⁻¹ s⁻¹ and hole concentration of 1.37 × 10¹⁸ cm⁻³. X-ray diffraction (XRD) measurements showed that the Li-doped ZnO films grown at different substrate temperatures were of completely (0 0 2)-preferred orientation.     

Optimal growth conditions for GdBa2Cu3O7 thin-film coated conductors characterized by polarized Raman scattering spectroscopy

High temperature superconducting GdBa₂Cu₃O₇ (GdBCO) thin films were grown by pulsed laser ablation. Textured MgO on metal substrates was used as a template for second generation wire applications. Growth conditions of GdBCO thin films were investigated for substrate temperature (T_s) and oxygen partial pressure (PO₂) during deposition. Superconducting critical currents of the films were obtained in the films grown at 790–810 °C of T_s and at 100–700 mTorr of PO₂. Scanning electron micrographs of the films revealed uniform and well-connected grains with some outgrown structures. X-ray θ–2θ scans of the films grown at 810 °C and 300–500 mTorr exhibited c-axis oriented texture. In-plane alignment and c-axis mosaic spread of the films were determined from X-ray Φ scans and rocking curves, respectively. Polarized Raman scattering spectroscopy was used to characterize optical phonon modes, oxygen content, cation disorder, and some possible second phases of the films. The Raman spectra of the films with large critical current density showed modes at 326–329 cm⁻¹, 444–447 cm⁻¹, 500–503 cm⁻¹ related to vibration of oxygen atoms. Origin of small peaks near 600 cm⁻¹ will be discussed as well. The information obtained from Raman scattering measurements will be useful for quality control of the conductors as well as optimization of the process conditions.     

Nitrogen-doped ZnO prepared by capillaritron reactive ion beam sputtering deposition

Nitrogen-doped ZnO thin films have been prepared by reactive ion beam sputtering deposition utilizing a capillaritron ion source. X-ray diffraction (XRD) analysis of the as-deposited film exhibits a single strong ZnO (002) diffraction peak centred at 34.40°. Post-growth annealing causes increase of grain size and decrease of c-axis lattice constant. Micro-Raman spectroscopy analysis of the as-deposited film shows strong nitrogen-related local vibration mode at 275, 582, 640 and 720 cm⁻¹, whereas the E₂ mode of ZnO at 436 cm⁻¹ can barely be identified. Annealing at 500-800 °C causes decrease of 275, 582, 640 and 720 cm⁻¹ and increase of 436 cm⁻¹ intensity, indicating out-diffusion of nitrogen and improvement of ZnO crystalline quality. Unlike un-doped ZnO, the surface roughness of nitrogen-doped ZnO deteriorates after annealing, which is also attributed to the out-diffusion of nitrogen. A nitrogen concentration of ∼10²¹/cm³ was observed while type conversion from n-type to p-type was not achieved, which is likely due to the formation of Zn_I-N_O or (N₂)_O that act as donor/double donors.     

Effects of seed layer on the structure and property of zinc oxide thin films electrochemically deposited on ITO-coated glass

ZnO films with different morphologies were deposited on the ITO-coated glass substrate from zinc nitrate aqueous solution at 65 °C by a seed-layer assisted electrochemical deposition route. The seed layers were pre-deposited galvanostatically at different current densities (i_sl) ranging from −1.30 to −3.0 mA/cm², and the subsequent ZnO films had been done using the potentiostatic technique at the cathode potential of −1.0 V. Densities of nucleation centers in the seed layers varied with increasing the current density, and the ZnO films on them showed variable morphologies and optical properties. The uniform and compact nanocrystalline ZnO film with (0 0 2) preferential orientation was obtained on seed layer that was deposited under the current density (i_sl) of −1.68 mA/cm², which exhibited good optical performances.     

Photoluminescence properties of nitrogen-doped ZnO films deposited on ZnO single crystal substrates by the plasma-assisted reactive evaporation method

Photoluminescence (PL) spectra of nitrogen-doped ZnO films (ZnO:N films) grown epitaxially on n-type ZnO single crystal substrates by using the plasma-assisted reactive evaporation method were measured at 5 K. In PL spectra, free exciton emission at about 3.375 eV was very strong and emissions at 3.334 and 3.31 eV were observed. These two emissions are discussed in this paper. The nitrogen concentration in ZnO:N films measured by secondary ion mass spectroscopy was 10^19-20 cm⁻³. Current-voltage characteristics of the junction consisting of an n-type ZnO single crystal substrate and ZnO:N film showed good rectification. Also, ultraviolet radiation and visible light were emitted from this junction under a forward bias at room temperature. It is therefore thought that ZnO:N films have good crystallinity and that doped nitrogen atoms play a role as acceptors in ZnO:N films to form a good pn junction. From these phenomena and the excitation intensity dependency of PL spectra, emissions at 3.334 and 3.31 eV were assigned to neutral acceptor-bound exciton (A⁰X) emission and a donor-acceptor pair (DAP) emission due to doped nitrogen, respectively.     

Formation of Al-N co-doped p-ZnO/n-Si (1 0 0) heterojunction structure by RF co-sputtering technique

Al-N co-doped ZnO (ZnO:Al-N) thin films were grown on n-Si (1 0 0) substrate by RF co-sputtering technique. As-grown ZnO:Al-N film exhibited n-type conductivity whereas on annealing in Ar ambient the conduction of ZnO:Al-N film changes to p-type, typically at 600 °C the high hole concentration of ZnO:Al-N co-doped film was found to be 2.86 × 10¹⁹ cm⁻³ and a low resistivity of 1.85 × 10⁻² Ω-cm. The current-voltage characteristics of the obtained p-ZnO:Al-N/n-Si heterojunction showed good diode like rectifying behavior. Room temperature photoluminescence spectra of annealed co-doped films revealed a dominant peak at 3.24 eV.     

Electrical and optical properties of ZnO films prepared by sputtering of ZnO targets containing AlN

ZnO films prepared from the ZnO target containing 2% AlN are transparent irrespective of radio frequency (RF) power. The obtained ZnO films have the carrier density of 3.8 × 10²⁰ cm⁻³ or less and the low mobility of 5.3-7.8 cm²/(V s). In the case of 5% AlN target, ZnO films prepared at 40, 60 and 80 W are transparent, whereas ZnO films prepared at 100 and 120 W are colored. As RF power increases from 40 to 120 W, the carrier density increases straightforwardly up to 5.5 × 10²⁰ cm⁻³ at 100 W and is oppositely reduced to 3.2 × 10²⁰ cm⁻³ at 120 W. In the case of 10% AlN target, ZnO films prepared at 60 W or more are colored, and have the carrier density of 4 × 10²⁰ cm⁻³ or less. The N-concentration in these colored films is estimated to be 1% or less. The Al-concentration in the ZnO films prepared from the 5 and 10% AlN targets is higher than 2%. The carrier density of the ZnO films containing Al and N atoms is nearly equal to that of ZnO films doped with Al atoms alone. There is no evidence in supporting the enhancement of the carrier density via the formation of N-Al_xZn_4−x clusters (4 ≥ x ≥ 2).     

Structural, optical and electronic properties of P doped p-type ZnO thin film

P doped ZnO films were grown on quartz by radio frequency-magnetron sputtering method using a ZnO target mixed with 1.5 at% P₂O₅ in the atmosphere of Ar and O₂ mixing gas. The as-grown P doped ZnO film showed n-type conductivity, which was converted to p-type after 800 °C annealing in Ar gas. The P doped ZnO has a resistivity of 20.5 Ω cm (p∼2.0×10¹⁷ cm⁻³) and a Hall mobility of 2.1 cm² V⁻¹ s⁻¹. XRD measurement indicated that both the as-grown and the annealed P doped ZnO films had a preferred (0 0 2) orientation. XPS study agreed with the model that the P_Zn-2V_Zn acceptor complex was responsible for the p-type conductivity as found in the annealed P-doped ZnO. Temperature-dependent photoluminescence (PL) spectrum showed that the dominant band is located at 3.312 eV, which was attributed to the free electronic radiative transition to neutral acceptor level (FA) in ZnO. The P_Zn-2V_Zn acceptor complex level was estimated to be at E_V=122 meV.     

Determination of electrical types in the P-doped ZnO thin films by the control of ambient gas flow

Phosphorus (P)-doped ZnO thin films with amphoteric doping behavior were grown on c-sapphire substrates by radio frequency magnetron sputtering with various argon/oxygen gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio without post-annealing. The P-doped ZnO films grown at a argon/oxygen ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of 1.5 × 10¹⁷ cm⁻³ and 2.5 cm²/V s, respectively. X-ray diffraction showed that the ZnO (0 0 0 2) peak shifted to lower angle due to the positioning of P³⁻ ions with a larger ionic radius in the O²⁻ sites. This indicates that a p-type mechanism was due to the substitutional P_O. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction light emitting diode showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Properties of ZnO thin films deposited on (glass,ITO and ZnO:Al) substrates

ZnO thin films were deposited on glass, ITO (In₂O₃; Sn) and on ZnO:Al coated glass by spray pyrolysis. The substrates were heated at 350 °C. Structural characterization by X-ray diffraction (XRD) measurements shows that films crystallize in hexagonal structure with a preferential orientation along (0 0 2) direction. XRD peak-shift analysis revealed that films deposited on glass substrate (−0.173) were compressive, however, films deposited onto ITO (0.691) and on ZnO:Al (0.345) were tensile. Scanning electron microscopies (SEM) show that the morphologies of surface are porous in the form of nanopillars. The transmittance spectra indicated that the films of ZnO/ITO/glass and ZnO/ZnO:Al/glass exhibit a transmittance around 80% in the visible region. An empirical relationship modeled by theoretical numerical models has been presented for estimating refractive indices (n) relative to energy gap. All models indicate that the refractive index deceases with increasing energy band gap (E_g).