多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术,分别沉积Ti和Ti/Al膜,经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序,分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27 关键词： 2薄膜')" href="#">多孔TiO₂薄膜 阳极氧化 紫外光吸收     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.     

氧氩比对SnO2/Ag/SnO2透明导电膜光电性能的影响

在室温及不同的氧氩比条件下,采用射频磁控溅射Ag层和直流磁控溅射SnO₂层,在载玻片衬底上制备出了SnO₂/Ag/SnO₂多层薄膜.用霍尔效应测试仪、四探针电阻测试仪和紫外-可见-近红外光谱仪等表征了薄膜的电学性质和光学性质.实验结果表明:当氧氩比为1:14时,所制得的薄膜的光电性质优良指数最大,为1.69×10^-2 Ω^-1;此时,薄膜的电阻率为9.8×10^-5 Ω·cm,方电阻为9.68 Ω/sq,在400~800 nm可见光区的平均光学透射率达85%;并且,在氧氩比为1:14时,利用射频磁控溅射Ag层和直流磁控溅射SnO₂层在PET柔性衬底上制备出了光电性质优良的柔性透明导电膜,其在可见光区的平均光学透过率达85%以上,电阻率为1.22×10^-4 Ωcm,方电阻为12.05 Ω/sq.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

低成本溶胶-凝胶法制备SiO2/TiO2双层膜的减反射与自清洁性能

将玻璃基底依次在低成本的SiO₂溶胶和TiO₂溶胶中浸渍后,在500 oC下煅烧制备了同时具备减反射与自清洁性能的SiO₂/TiO₂双层膜．该膜的光学性能与结构特征分别通过紫外-可见分光光度计和场发射扫描电镜进行了表征．同时,源于超亲水性和光催化作用的自清洁性能也凸显出来．实验结果表明制备SiO₂/TiO₂双层膜对光的透射率最高可达到95%,同时具备自清洁性能．     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

TiO2 nanoparticle thin film deposition by matrix assisted pulsed laser evaporation for sensing applications

The MAPLE technique has been used for the deposition of nanostructured titania (TiO₂) nanoparticles thin films to be used for gas sensors applications. An aqueous solution of TiO₂ nanoparticles, synthesised by a novel chemical route, was frozen at liquid nitrogen temperature and irradiated with a pulsed ArF excimer laser in a vacuum chamber. A uniform distribution of TiO₂ nanoparticles with an average size of about 10 nm was deposited on Si and interdigitated Al₂O₃ substrates as demonstrated by high resolution scanning electron microscopy-field emission gun inspection (SEM-FEG). Energy dispersive X-ray (EDX) analysis revealed the presence of only the titanium and oxygen signals and FTIR (Fourier transform infra-red) revealed the TiO₂ characteristic composition and bond. A comparison with a spin coated thin film obtained from the same solution of TiO₂ nanoparticles is reported. The sensing properties of the films deposited on interdigitated substrates were investigated, too.     

CO sensor derived from mesostructured Au-doped SnO2 thin film

Pure and Au-doped mesostructured SnO₂ thin films were successfully prepared by using non-ionic surfactant Brij-58 (polyoxyethylene acyl ether) as organic template and tin tetrachloride and hydrogen tetrachloroaurate(III) trihydrate as inorganic precursor. Thin films were deposited onto the glass substrates at 450 °C by simple spray pyrolysis technique. The novel mesostructured tin oxide thin films with different Au concentration exhibit highly selective response towards CO. The correlation of the Au incorporation in the mesostructure with particular morphology and gas sensing behavior is discussed using scanning electron microscopy (SEM), X-ray diffraction (XRD), BET surface area and transmission electron microscopy (TEM) studies.     

同步辐射光激励的二氧化硅薄膜刻蚀研究

利用热氧化法在硅晶片上生长SiO₂薄膜，结合光刻和磁控溅射技术在SiO₂薄膜表面制备接触型钴掩模，通过掩模方法在硅表面开展了同步辐射光激励的表面刻蚀研究，在室温下制备了SiO₂薄膜的刻蚀图样.实验结果表明：在同步辐射光照射下，通入SF₆气体可以有效地对SiO₂薄膜进行各向异性刻蚀，并在一定的气压范围内，刻蚀率随SF₆气体浓度的增加而增加，随样品温度的下降而升高；如果在同步辐射光照射下，用SF₆和O₂的混合气体作为反应气体，刻蚀过程将停止在SiO₂/Si界面，即不对硅刻蚀，实现了同步辐射对硅和二氧化硅两种材料的选择性刻蚀；另外，钴表现出强的抗刻蚀能力，是一种理想的同步辐射光掩模材料. 关键词： 同步辐射刻蚀 接触型钴掩模 二氧化硅薄膜     

Annealing effects on the structure and electrical characteristics of amorphous Er2O3 films

Amorphous Er 2 O 3 films are deposited on Si (001) substrates by using reactive evaporation.This paper reports the evolution of the structure,morphology and electrical characteristics with annealing temperatures in an oxygen ambience.X-ray diffraction and high resolution transimission electron microscopy measurement show that the films remain amorphous even after annealing at 700 C.The capacitance in the accumulation region of Er 2 O 3 films annealed at 450 C is higher than that of as-deposited films and films annealed at other temperatures.An Er 2 O 3 /ErO x /SiO x /Si structure model is proposed to explain the results.The annealed films also exhibit a low leakage current density (around 1.38 × 10 4 A/cm 2 at a bias of 1 V) due to the evolution of morphology and composition of the films after they are annealed.     

Optical and hydrophilic properties of Cr doped TiO2-SiO2 nanostructure thin film

Cr doped TiO₂-SiO₂ nanostructure thin film on glass substrates was prepared by a sol-gel dip coating process. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the structural and chemical properties of the films. A UV-vis spectrophotometer was used to measure the transmittance spectra of the thin film. The hydrophilicity of the thin film during irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that Cr doping has a significant effect on the transmittance and super-hydrophilicity of TiO₂-SiO₂ thin film.     

磁控溅射法合成纳米β-FeSi2/a-Si多层结构

β-FeSi₂作为一种环境友好的半导体材料，颗粒化及非晶化正在成为提高其应用性能和改善薄膜质量、膜基界面失配度的有效途径.利用射频磁控溅射法在单晶Si基体上沉积Fe/Si多层膜，合成纳米β-FeSi₂/Si多层结构.通过透射电子显微镜、高分辨电子显微术等分析手段，研究了多层结构和制备工艺之间的相互关系.研究结果表明，采用磁控溅射Fe/Si多层膜的方法，不需要退火就可以直接沉积得到β-FeSi₂相小颗粒.β-FeSi₂相 关键词： 2')" href="#">β-FeSi₂ 磁控溅射 透射电子显微镜 半导体薄膜     

Structural, electrical and optical properties of TiO2 doped WO3 thin films

TiO₂ doped WO₃ thin films were deposited onto glass substrates and fluorine doped tin oxide (FTO) coated conducting glass substrates, maintained at 500 °C by pyrolytic decomposition of adequate precursor solution. Equimolar ammonium tungstate ((NH₄)₂WO₄) and titanyl acetyl acetonate (TiAcAc) solutions were mixed together at pH 9 in volume proportions and used as a precursor solution for the deposition of TiO₂ doped WO₃ thin films. Doping concentrations were varied between 4 and 38%. The effect of TiO₂ doping concentration on structural, electrical and optical properties of TiO₂ doped WO₃ thin films were studied. Values of room temperature electrical resistivity, thermoelectric power and band gap energy (E_g) were estimated. The films with 38% TiO₂ doping in WO₃ exhibited lowest resistivity, n-type electrical conductivity and improved electrochromic performance among all the samples. The values of thermoelectric power (TEP) were in the range of 23-56 μV/K and the direct band gap energy varied between 2.72 and 2.86 eV.     

Photoluminescence in amorphous (PbLa)TiO3 thin films deposited on different substrates

Pb_1−XLa_XTiO₃ thin films, (X=0.0; 13 and 0.27 mol%) were prepared by the polymeric precursor method. Thin films were deposited on Pt/Ti/SiO₂/Si (1 1 1), Si (1 0 0) and glass substrates by spin coating, and annealed in the 200-300°C range in an O₂ atmosphere. X-ray diffraction, scanning electron microscopy and atomic force microscopy were used for the microstructural characterization of the thin films. Photoluminescence (PL) at room temperature has been observed in thin films of (PbLa)TiO₃. The films deposited on Pt/Ti/SiO₂/Si substrates present PL intensity greater than those deposited on glass and silicon substrates. The intensity of PL in these thin films was found to be dependent on the thermal treatment and lanthanum molar concentration.     

Fabrication of textured SnO2:F thin films by spray pyrolysis

Transparent conductive SnO₂:F thin films with textured surfaces were fabricated on soda-lime-silica glass substrates by spray pyrolysis. Structure, morphology, optical and electrical properties of the films were investigated. Results show that the film structure, morphology, haze, transmittance and sheet resistance are dependent on the substrate temperature and film thickness. An optimal 810 nm-thick SnO₂:F film with textured surface deposited at 520 °C exhibits polycrystalline rutile tetragonal structure with a (2 0 0) orientation. The sheet resistance, average transmittance in visible region, and haze of this film were 8 Ω/□, 80.04% and 11.07%, respectively, which are suitable for the electrode used in the hydrogenated amorphous silicon solar cells.     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

Preparation, structure and photo-catalytic performances of hybrid Bi2SiO5 modified Si nanowire arrays

Bi₂SiO₅ modified Si nanowire array films were fabricated as photo-catalysts via dip-coating Bi(NO₃)₃ on silver-assisted electroless wet chemical etching Si nanowires and subsequently annealing. The structures and morphologies of as-prepared samples are characterized by X-ray diffraction, Fourier transform infrared spectrum, scanning electron microscopy and transmission electron microscopy. The results of photocatalytic experiments indicated that the Bi₂SiO₅ modified Si nanowire arrays benefit the improvement for efficient electron-hole separation and photo-catalytic stability, thereby possessing superior photo-degradation performance. These hybrid nanowire arrays will be promising materials for photo-catalysts and degradation agents.     

Structural investigations of TiO2:Tb thin films by X-ray diffraction and atomic force microscopy

In this work, structural investigations of TiO₂ thin films doped with Tb at the amount of 0.4, 2 and 2.6 at.% have been outlined. Thin films were deposited on Si and SiO₂ substrates by high energy reactive magnetron sputtering from mosaic Ti-Tb target. The influence of Tb dopant amount, post-annealing treatment and kind of applied substrate on microstructure has been discussed. Thin films were investigated by means of X-ray diffraction (XRD) and atomic force microscopy (AFM). XRD analysis revealed the existence of crystalline TiO₂ in anatase and rutile forms, depending on Tb amount in examined samples. AFM images show that as-deposited samples with 0.4 at.% concentration of terbium (anatase structure) have bigger crystallites as compared to 2% and 2.6 at.% of Tb (rutile structure). The additional annealing at 1070 K results in a mixed anatase (77%) and rutile (23%) structure.