基于低温辐射计的InGaAs陷阱探测器高精度光辐射定标研究

介绍了以InGaAs陷阱探测器作为传递探测器,基于低温辐射计的高精度光辐射定标和标准传递实验与研究。在红外(944-1589nm)三个波长初步给出了InGaAs陷阱探测器绝对光谱响应率定标结果。InGaAs陷阱探测器绝对光谱响应率的联合不确定最大为0.655%,最小为0.026%。     

一种近红外探测器的光谱响应率测量

对近红外辐射功率光谱绝对响应率的定标技术进行了研究。设计了一种制冷扩展波长型的InGaAs探测器，为了使其能够作为功率传递的标准探测器工作在（1.2～2.5）μm波长范围，对探测器的光谱响应率进行了测量。首先在1260nm波长下进行绝对功率传递的标定试验，然后用基于红外单色仪的光谱比较系统（SCF）测量了探测器的相对光谱响应率。结合2个步骤的数据，最终可以得到探测器的绝对光谱响应率。     

硅陷阱探测器在350—1064 nm波段的绝对光谱响应度定标

介绍了利用钛宝石可调谐激光器、倍频器和单波长激光器作为光源,在24个波长分立点定标了三个硅陷阱探测器的绝对光谱响应度,解决了红外激光的精确定位与调整、窗口透过率模拟定标等关键技术.结果显示：在激光波长为412—800nm时,三个陷阱探测器定标的不确定度约低于0.05％;当激光波长大于800nm以及低于355nm时,获得的陷阱探测器的定标不确定度约低于0.065％.硅陷阱探测器可以作为空间各类遥感器在350—1064nm波段定标的传递标准探测器. 关键词： 陷阱探测器 低温辐射计 光谱响应度 辐射定标     

溯源至低温辐射计的硅陷阱探测器紫外波段绝对光谱响应度测量

介绍了溯源至低温辐射计的紫外绝对光谱响应度测量装置,对硅陷阱探测器在三个激光波长点进行了绝对光谱响应度校准实验.测量了硅陷阱探测器的空间均匀性和非线性系数,分析了影响测量准确度的各不确定度分量.实验表明:硅陷阱探测器在紫外波段266、325、379 nm三个激光波长点处的绝对光谱响应度测量扩展不确定度分别为0.19％、0.14％、0.11％,可作为紫外波段光辐射功率基准保持和传递的标准探测器,用于提高紫外波段光谱辐射度的校准能力.     

可见-近红外(488～944 nm)基于低温辐射计的高精度光辐射绝对定标研究

报道了可见-近红外波段(488～944nm)基于低温辐射计的光谱辐射功率定标和标准传递实验和研究,并对测量结果的各个不确定因素进行了测量和分析。首先低温辐射计采用电替代方法测量单个波长激光绝对光功率,测量不确定度低于0．016％。然后利用低温辐射计定标作为标准传递探测器的硅陷阱探测器,从而建立可见-近红外波段陷阱探测器的绝对光谱响应率标准,其不确定度小于0．028％。结果证明了在此波段以探测器为基础建立和传递高精度光辐射标准的合理性和可行性。     

溯源至低温辐射计的硅陷阱探测器紫外波段绝对光谱响应度测量（英文）

介绍了溯源至低温辐射计的紫外绝对光谱响应度测量装置,对硅陷阱探测器在三个激光波长点进行了绝对光谱响应度校准实验.测量了硅陷阱探测器的空间均匀性和非线性系数,分析了影响测量准确度的各不确定度分量.实验表明:硅陷阱探测器在紫外波段266、325、379nm三个激光波长点处的绝对光谱响应度测量扩展不确定度分别为0.19%、0.14%、0.11%,可作为紫外波段光辐射功率基准保持和传递的标准探测器,用于提高紫外波段光谱辐射度的校准能力.     

一种太赫兹探测器绝对光谱响应度测量方法研究

绝对光谱响应度是探测器的重要技术参数之一，随着太赫兹探测技术的发展，精确测量太赫兹探测器的绝对光谱响应度变得越来越重要。由于在太赫兹波段缺乏连续可调谐的太赫兹光源以及分光系统，因此无法采用传统测量红外探测器绝对光谱响应度的方法来实现对太赫兹探测器绝对光谱响应度的测量。基于反射法测量了2～10 THz相对光谱响应度，通过CO₂泵浦气体激光器作为泵浦光源测量了2.52和4.25 THz绝对响应度，转化得到2～10 THz探测器的绝对光谱响应度，并且对2.52和4.25 THz绝对响应率和相对光谱响应度这两个频率点进行了相互验证，2.52和4.25 THz绝对响应度测量值之比为0.753,相对光谱响应度测量平均值之比为0.749,两者之差仅为0.004,因此，说明本文采用的反射法测量太赫兹探测器相对光谱响应度的方法是可行的。另外水汽在太赫兹波段的测试有很大的影响，对1.5～10 THz波段大气的衰减特性进行了测试，试验表明水汽对太赫兹波有明显的衰减作用，在不同环境湿度下测量时会产生不同的结果，因此在太赫兹探测器测量过程中需要严格的控制大气的湿度，从测试数据可得到，大气中...     

硅陷阱探测器绝对光谱响应率校准实验研究

以Ar^＋Kr^＋激光器、He—Ne激光器和半导体泵浦激光器作为光源,利用激光稳功率装置以及闭环机械制冷型低温辐射计,校准了硅陷阱探测器的绝对光谱响应率。在硅探测器的光谱响应范围400-1100nm内,选择476．1nm、488nm、514．7nm、521nm、568nm、632．8nm、647．1nm、1064nm共8条谱线进行了实验研究。实验数据表明,绝对光谱响应率的测量不确定度为可见光波段优于0．02％,1064nm波长点优于0．03％。     

基于探测器标准的高精度光谱辐射标准光源

本文在评述低温绝对辐射计和SIRCUS发展的基础上,讨论了基于探测器标准的光谱可调谐自校准标准光源的工作原理、发展与应用前景。在探测器型光谱辐射标准研究方面,工作在液氦温度的低温绝对辐射计不确定度达0.01%。美国国家标准与技术研究院(NIST)建立的均匀光源光谱辐照度和光谱辐亮度响应度定标装置(SIRCUS)采用一系列激光器,由低温绝对辐射计传递的硅陷阱探测器定标,不确定度已达到0.1%,成功应用于空间遥感仪器高精度辐射定标。分析认为,发展中的基于探测器标准的光谱可调谐自校准标准光源,定标精度高,自行校正老化、衰减,保证了定标精度长期稳定。     

基于标准探测器研究标准灯光谱辐照度和漫反射板双向反射分布函数随波长的变化

用光谱辐照度标准灯的光谱辐照度标定内部照明的积分球开口光谱辐亮度,这一技术目前已比较成熟,通过两种方式推导出的传递仪器光谱辐亮度响应度之比随波长而变化.针对这一现象,构建了基于标准探测器的绝对辐亮度计和绝对辐照度计.用所构建的绝对辐射计在4个波长处标定光谱辐照度标准灯及标准漫反射板的变化情况,得出标准灯实际光谱辐照度值...     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.