La2/3Ca1/3MnO3中的输运机制与CMR效应

研究了超大磁阻材料La2/3Ca1/3MnO3的磁电特性，发现由电阻测量得到的绝缘体．金属相变与由磁化曲线得到的顺磁-铁磁相变温区完全一致，均随磁场的增强推向高温区。结果证明样品输运行为的变化起因于磁结构的变化，在Tc附近产生超大巨磁电阻效应。     

金属纳米粒子在聚合物中的磁致排列──实验及分子动力学模拟

用磁场控制碳包镍纳米颗粒在环氧树脂中的排列,制备了具有优异电学性能的一维有序的纳米复合材料.在添加质量分数为3%-10%的镍纳米颗粒时,导电率提高了3个数量级,介电常数增大了2-3倍.对纳米颗粒的磁致排列进行了分子模拟,结果表明,偶极强相互作用是导致纳米粒子排列的主要原因,排列过程经历了聚合、成链和粗化等阶段,成链的时间尺度在秒数量级.模拟结构与实验观察结果基本一致.     

纳米尺度AgBr/I乳剂颗粒的光电子衰减行为

本文以鱼明胶为保护介质,在不同的鱼明胶 溴化银比值下,采用双注法制备AgBr/I纳米颗粒乳剂,以TEM观测颗粒形态,据此统计得出该乳剂中AgBr/I纳米颗粒平均粒径(d)及粒径分布系数(|±σ|/d).鱼明胶 溴化银比值在0.31g/mmol-0.62g/mmol范围内,颗粒平均粒径仅有微小变化,但粒径分布系数随该比值的增大而减小,表明颗粒均一性提高.采用微波光导法对该纳米尺度AgBr/I乳剂颗粒的光电子衰减过程进行测试,结果表明,纳米尺度Ag-Br/I乳剂颗粒的光电子衰减过程为双组分,即初始快衰减和随后慢衰减,其衰减过程皆符合一级动力学规律.该纳米尺度乳剂颗粒光电子寿命较常规乳剂颗粒明显缩短.     

纳米晶钛酸钡的介电性能

采用硬脂酸凝胶法制备了纳米晶BaTiO3,用差热热重分析、红外光谱分析、X射线衍射分析等手段对产物的形成过程、晶型、粒径进行了分析.通过对材料介电性能的研究发现,纳米材料的静态介电常数远大于常规材料的介电常数,随着粒径的减小,纳米材料的介电常数先增大而后有所降低.随着环境湿度的升高,纳米晶材料的介电常数逐渐增大,在高湿度条件下,其介电常数与湿度成线性关系.     

脉冲电沉积钯镍合金纳米颗粒及其甲酸电催化氧化

采用方波脉冲方法,在钯镍合金电解液中成功地电化学沉积出镍原子含量分别为12.0%、16.4%和22.6%的钯镍合金纳米颗粒.钯镍合金纳米颗粒为球状,粒径50~80 nm.随钯镍合金生长电位负移,合金的镍含量提高,其纳米颗粒大小基本相似但纳米颗粒数目增多,交联度提高和真实活性面积增大.钯镍合金纳米颗粒镍含量提高,在硫酸溶液中其氢弱吸附峰电流增大.钯镍合金纳米颗粒电极的甲酸电催化氧化活性较好,随合金纳米颗粒的镍含量提高和交联度增加,合金纳米颗粒电极的甲酸电催化氧化稳定性更高.     

纳米复合材料中界面动态特性的扫描静电显微技术研究

纳米复合材料中的微观界面结构和界面作用对材料的宏观介电性能, 如介电常数、介电损耗、击穿强度等有十分重要的影响. 本文发展了一种基于扫描静电显微探针技术的测量方法, 可以直接表征二氧化钛/环氧树脂纳米复合材料的微观界面结构及相应的动态介电响应行为. 实验中利用扫描探针的纳米尺度分辨能力, 探测到不同温度下环氧树脂纳米复合材料的局域动态介电响应变化过程, 从而获得纳米颗粒与高分子界面相互作用及极化相关的温度特性. 进一步通过对二氧化钛纳米颗粒进行表面修饰, 得到了两种不同特性的二氧化钛/环氧树脂界面, 验证了不同界面作用引起的复合材料界面区域与非界面区域高分子链介电损耗图像的反差.     

脉冲电沉积Pd-Ni合金纳米颗粒及其甲酸电催化氧化

采用方波脉冲方法,在钯镍合金电解液中成功地电化学沉积出镍原子含量分别为12.0%、16.4%和22.6%的钯镍合金纳米颗粒. 钯镍合金纳米颗粒为球状,粒径50 ~ 80 nm. 随钯镍合金生长电位负移,合金的镍含量提高,其纳米颗粒大小基本相似但纳米颗粒数目增多,交联度提高和真实活性面积增大. 钯镍合金纳米颗粒镍含量提高,在硫酸溶液中其氢弱吸附峰电流增大. 钯镍合金纳米颗粒电极的甲酸电催化氧化活性较好,随合金纳米颗粒的镍含量提高和交联度增加,合金纳米颗粒电极的甲酸电催化氧化稳定性更高.     

溶胶凝胶法制备CdS/SiO2量子点玻璃的研究

通过溶胶凝胶转变过程制备了硫化镉／二氧化硅量子点复合玻璃材料（硫化镉在复合材料中的最大掺杂质量比可达到30％）；并针对两种催化剂对复合体系的不同影响对这一类体系的物理化学性质进行了较为系统的研究．复合体系的溶胶凝胶转变点可通过对复合溶胶粘度随时间变化的观测而确定．TEM法与低频Raman散射法的测定表明实验制备的样品中CdS颗粒基本为nm级的球形粒子。其CdS颗粒粒径随CdS含量增加而增大。随CdS／SiO2量子点玻璃材料中CdS颗粒粒径的减小，其吸收光谱中的吸收边界与常规尺寸颗粒的吸收光谱边界相比有明显的蓝移，体现出显著的量子效应．适宜的热处理过程对复合材料中CdS颗粒粒径的减小和量子效应的增强起着有利的作用．     

水滑石型磁性纳米载药粒子的制备及其体外药物释放性能研究

通过调变镁铁尖晶石的含量, 采用一步共沉淀法制备了一系列具有核壳结构的水滑石型磁性纳米载药粒子, 对其微结构、热稳定性、磁性和药物释放性能进行了系统的研究. 结果表明这种磁性纳米载药粒子是一种具有以镁铁尖晶石为核层、双氯酚酸(Diclofenac, DIC)插层水滑石(DIC-LDH)为壳层的复合纳米粒子, 粒径在90～180 nm之间. 其中壳层DIC-LDH的晶粒尺寸D₁₁₀和层板电荷密度随磁核含量的增大而逐渐减小. 磁性纳米载药粒子的载药量随磁核含量的增大而逐渐减小, 而其比饱和磁化强度则随着磁核含量的增大逐渐增大. 体外释放实验表明, 无外加磁场时, 磁核含量增大, 壳层DIC-LDH粒径减小, 磁性纳米载药粒子药物释放速率逐渐增大|外加1500 G磁场时, 磁核含量增大, 磁致团聚程度增大, 其药物释放速率逐渐减小.     

具有包藏结构的三元聚丙烯纳米复合材料结构与性能关系的研究

制备了一种新型聚丙烯 丁苯橡胶 纳米碳酸钙三元纳米复合材料 .研究结果显示 ,复合材料中的大多数纳米碳酸钙粒子被包藏在丁苯橡胶中 ,并与之共同形成分散于聚丙烯树脂中的分散相 ,这种聚丙烯纳米复合材料具有高刚性、高韧性、高耐热性和高的结晶速率 .系统研究了成核剂苯甲酸钠的加入和纳米碳酸钙的用量对该类纳米复合材料相态结构、结晶形态和结晶动力学的影响 ,以及具有包藏结构的分散相粒径和PP中β晶含量对材料性能的影响 .结果表明 ,苯甲酸钠的加入和纳米碳酸钙用量的提高均可使体系中分散相粒径减小 ,结晶速率加快 ,进而使材料的韧性、刚性和耐热性提高 .     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.