溶剂浮选分光光度法测定痕量铜

在酸性条件下，Cu(Ⅱ)-SCN－结晶紫形成很深颜色的三元离子缔合物，通过浮选富集，在587nm处测其在有机溶剂中的浓度，建立了测定痕量铜的新方法。该法用于测定环境水样和经处理的茶多酚中的铅含量．摩尔吸光系数达1．68×106L.mol-1．cm－1，线性范围0．50～60μg／L。回收率为99．4％～101．2％，结果令人满意。     

硅藻土吸附在线柱富集-火焰原子吸收光谱法测定环境水样中痕量铜

提出了硅藻土吸附在线柱富集-火焰原子吸收光谱法测定环境水样中痕量铜的方法。利用硅藻土对环境水样中痕量铜在线预富集,浓集因子达到27.6,使火焰原子吸收光谱法的检测能力达到测定环境水样中痕量铜的要求。方法检出限为0.32μg.L-1,RSD(20μg.L-1)为3.52%,加标回收率为97.0%~105.0%。     

壳聚糖富集火焰原子吸收法测定水中痕量铜

采用壳聚糖修饰钨丝基质螺旋卷，直接浸入含有痕量铜的pH5．0的Brltton-Robinson缓冲溶液中，经电磁搅拌富集一定时间后，将其转移至空气／乙炔火焰燃烧器上，利用火焰原子吸收光谱法简便快速测定水中痕量铜。方法的线性范围为2—75μg／L；检出限为0．98μg／L。同一支钨丝螺旋卷重复涂敷壳聚糖富集Cu，RSD(n=6)为2．7％。     

纳米二氧化钛分离富集石墨炉原子吸收光谱法测定水样中痕量铅

提出了纳米TiO2分离富集,GFAAS测定水样中痕量铅的新方法。详细考察了纳米TiO2对铅的吸附行为,结果表明：在pH4．0时,Pb^2 可被纳米TiO2定量富集,吸附于纳米TiO2上的Pb^2 可用0．1mol／L的硝酸完全解脱。本法对Pb^2 的检出限为52ng／L,相对标准偏差为4．7％(n=10,C=0．02mg／L)。本法已用于实际水样中铅的测定,结果满意。     

锂皂石修饰碳糊电极测定痕量铜的研究

报道了锂皂石修饰碳糊电极测定痕量铜，在含０．００１ｍｏｌ／Ｌ ＫＣｌ Ｃｕ＾＋２的试液中，开路富集后介质交换到０．０５ｍｏｌ／Ｌ ＫＣｌ中，用微分脉冲伏安法测定，检测限为７．０ｎｇ／ｍＬ。常见阳离子基本不干扰，可不经预先分离直接测定精金矿中铜的含量，结果良好。还探讨了Ｃｕ＾＋２在锂皂石修饰碳糊电极上的反应机理。     

铜（铅）—Ferron—氯化四苯胂络合物吸附波研究

在ＨＣｌ－六次甲基四胺介质中，铜（铅）－Ｆｅｒｒｏｎ－氯化四苯胂络合物产生灵敏的络合吸附波。峰电位分别为－０．４１Ｖ和－０．５７Ｖ。峰电流与铜、铜浓度分别在０．０００４－０．４μｇ／ｍＬ和０．００２－０．８μｇ／ｍＬ之间呈线性关系，检出限分别为０．０００２μｇ／ｍＬＣｕ和０．００１μｇ／ｍＬＰｂ。研究了极谱波的性质和电极反应机理。用拟定的方法连续测定水样和食品中的铜、铜，结果满意。     

用DDTC—Zn作载体流动注射在线共沉淀预富集火焰原子吸收法测定人…

提出了在高酸度下流动性射在线共沉淀预富集－火焰原子吸收法测定痕量铅的新体系。在０．５ｍｏｌ／Ｌ ＨＣｌ介质中痕量铅与ＤＤＴＣ－Ｚｎ螯合物产生共沉淀。在线生成的沉淀物收集在编结反应器中，用甲基异丁酮溶解沉淀并直接引入火焰原子化器中进行测定。经４０ｓ富集，检测限为２．７μｇ／Ｌ，测定含量为２００μｇ／Ｌ的铅时，相对标准偏差为１．３％，建立的方法已成功地应用于人发标准参考物中和水样中痕量铅的测定。     

用DDTC-Zn作载体流动注射在线共沉淀预富集火焰原子吸收法测定人发和水样中的痕量铅

提出了在高酸度下流动注射在线共沉淀预富集－火焰原子吸收法测定痕量铅的新体系。在０．５ｍｏｌ／ＬＨＣｌ介质中痕量铅与ＤＤＴＣ－Ｚｎ螯合物产生共沉淀。在线生成的沉淀物收集在编结反应器中，用甲基异丁酮溶解沉淀并直接引入火焰原子化器中进行测定。经４０ｓ富集，检测限为２．７μｇ／Ｌ。测定含量为２００μｇ／Ｌ的铅时，相对标准偏差为１．３％。建立的方法已成功地应用于人发标准参考物中和水样中痕量铅的测定     

气提法富集气相色谱／质谱法测定水中痕量挥发有机物

作者改进了气提法富集水中痕量挥发性有机物装置。研究了实验条件对水中痕量有机物富集的影响，并确定了最佳富集条件。以气提法富集气相色谱／质谱法（ＧＣ／ＭＳ）测定了水样中痕量挥发性有机物，取得了满意的结果。     

甲壳素修饰碳糊电极测定痕量铜

报道了采用甲壳素修饰碳糊电极测定痕量铜的方法。通过开路富集，Ｃｕ６２＋和甲壳素形成络合物富集于电极表面，然后经介质交换，电位还原再进行阳熔出伏安测定。在浓度为３．０×１０＾－９－９．０×１２０＾－７ｍｏｌ／Ｌ范围内，峰电流与痕量铜浓度呈线性关系，检测限为１．０×１０＾－９ｍｏｌ／Ｌ。同时，对电极反应的机理进行了讨论。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.