非负载型磷化钼加氢精制催化剂的研制

 尽管有相当多的文献和专利报道了含磷加氢精制催化剂的研究及磷的加入对Mn-Ni、Ni-Mo、Ni-W、Co-Mo、Mo、W、Ni、Co等各类加氢精制催化剂结构、及HDS、HDN活性的影响，并证明了磷或含磷化合物可作为加氢精制催化剂的助剂和稳定剂，但对于磷化物加氢催化剂的合成及对其HDS、HDN活性的研究还很少。本文在较低温度下用氢气直接还原磷钼酸铵盐得到非负载型的磷化钼催化剂，并以制备的磷化钼为活性组分，以SiC和γ-Al2O3为稀释剂，选择高浓度和低浓度的吡啶、噻吩和环己烯的混合物为模型化合物，以环己烷作溶剂，测定了制备催化剂的HDS、HDN及HYD活性。结果表明，所研制的非负载型磷化钼加氢精制催化剂对两种含有吡啶、噻吩和环己烯的模型化合物具有同时HDN, HDS 和 HYD的性能。     

一种新型加氢精制磷化钨催化剂的研究

采用偏钨酸铵{(NH4)2W4O13·18H2O}与磷酸氢二铵{(NH4)2HPO4}溶解、蒸发、焙烧和程序升温还原的方法,制备了无负载WP催化剂.利用XRD和BET对合成样品进行表征,采用TG/DTA方法对催化剂前体的氢还原过程进行考察.以制备的磷化钨为活性组分,Al2O3为稀释剂,在空速为4h-1、氢油比为1000、反应压力为3.0MPa、不同反应温度的条件下,对吡啶加氢脱氮、噻吩加氢脱硫和模型化合物为二苯并噻吩(含3000ppm硫)、喹啉(含2000ppm磷)和环己烷(溶剂)加氢脱硫(HDS)和加氢脱氮(HDN)反应活性进行测定,结果表明:无负载WP催化剂有相当的活性,其对大分子脱氮、脱硫活性明显优于对小分子脱氮、脱硫活性.     

还原温度对MoP催化剂加氢精制性能的影响

 通过程序升温还原磷钼酸盐前体的方法制备了无负载磷化钼(MoP)催化剂,并采用XRD,BET,XPS和高压连续微反技术,考察了催化剂的性质,研究了还原温度对催化剂HDN,HDS和HYD性能的影响. 结果表明,在还原温度为600～800 ℃范围内,成功制备出磷化钼催化剂. 高压连续微反结果表明,MoP的催化特性与其比表面积、还原度和表相组成有关,比表面积大、还原度适中和表相Moδ+/Pδ-比适中的磷化钼具有更高的催化活性; 650～700 ℃为最合适的还原温度,高于或低于该温度时所制备的MoP催化剂活性均大幅度下降. 在合适的条件下,MoP催化剂对噻吩HDS,吡啶HDN和环己烯HYD的转化率可分别达到94.3%,100.0%和90.3%.     

制备条件对磷化钼加氢脱硫催化活性的影响

采用程序升温还原方法制得磷化钼(MoP)催化剂,在常压连续微型化反应装置中,以噻吩为模型化合物,对催化剂的加氢脱硫活性进行评价。考察了还原温度、磷钼摩尔比、不同磷源等制备条件对MoP催化活性的影响。实验结果表明,在MoP生成温度区间内,随着还原温度的升高,催化剂活性降低;磷钼摩尔比为1∶1时,噻吩转化率最高,而磷钼摩尔比为1∶2和2∶1时制备催化剂的催化活性相当;采用磷酸二氢铵、磷酸铵以及磷酸为磷源,均可制得磷化钼,而以磷酸二氢铵为磷源时制备磷化钼催化剂的活性最佳。在噻吩加氢脱硫反应条件下反应后,不同磷源制备的磷化钼整体物相均没有发生变化。     

助剂镍/钴对磷化钨催化剂加氢精制性能的影响

在共浸渍法制备磷化钨／γ-Al2O3催化剂基础上，分别加人1％、3％、5％、7％和9％(占活性组分比例)的助剂镍或钴，制得负载30％含助剂镍／钴磷化钨／γ-Al2O3系列催化剂，考察了助剂及其加人比例对催化剂加氢脱硫和加氢脱氮性能的影响．结果表明，加人适当比例的助剂镍或钴，有利于提高磷化钨／γ-Al2O3催化剂的加氢脱硫活性，当助剂含量分别为5％镍或7％钴时，催化剂的噻吩加氢脱硫率最高；助剂镍对磷化钨／γ-Al2O3催化剂的加氢脱氮反应不利，而加人适当比例助剂钴有利于提高催化剂加氢脱氮活性，当助剂钴含量为5％时，催化剂吡啶加氢脱氮率最高．温度对磷化钨／γ-Al2O3催化剂加氢精制性能有一定影响，高温有利于加氢脱硫反应，低温有利于加氢脱氮反应．     

ZnSO_4和La_2O_3作共修饰剂单金属Ru催化剂上苯选择加氢制环己烯

用沉淀法制备了单金属纳米Ru(0)催化剂,考察了ZnSO4和La2O3作共修饰剂对该催化剂催化苯选择加氢制环己烯性能的影响,并用X射线衍射(XRD)、X射线荧光(XRF)光谱、X射线光电子能谱(XPS)、俄歇电子能谱(AES)、透射电镜(TEM)和N2物理吸附等手段对加氢前后催化剂进行了表征.结果表明,在ZnSO4存在下,随着添加碱性La2O3量的增加,ZnSO4水解生成的(Zn(OH)2)3(ZnSO4)(H2O)x(x=1,3)盐量增加,催化剂活性单调降低,环己烯选择性单调升高.当La2O3/Ru物质的量比为0.075时,Ru催化剂上苯转化率为77.6%,环己烯选择性和收率分别为75.2%和58.4%.且该催化体系具有良好的重复使用性能.传质计算结果表明,苯、环己烯和氢气的液-固扩散限制和孔内扩散限制都可忽略.因此,高环己烯选择性和收率的获得不能简单归结为物理效应,而与催化剂的结构和催化体系密切相关.根据实验结果,我们推测在化学吸附有(Zn(OH)2)3(ZnSO4)(H2O)x(x=1,3)盐的Ru(0)催化剂有两种活化苯的活性位:Ru0和Zn2+.因为Zn2+将部分电子转移给了Ru,Zn2+活化苯的能力比Ru0弱.同时由于Ru和Zn2+的原子半径接近,Zn2+可以覆盖一部分Ru0活性位,导致解离H2的Ru0活性位减少.这导致了Zn2+上活化的苯只能加氢生成环己烯和Ru(0)催化剂活性的降低.本文利用双活性位模型来解释Ru基催化剂上的苯加氢反应,并用Hückel分子轨道理论说明了该模型的合理性.     

Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

二乙醇胺作添加剂Ru-Zn催化剂上苯选择加氢制环己烯

采用共沉淀法制备了Ru-Zn催化剂,考察了二乙醇胺的添加对Ru-Zn催化剂上苯选择加氢制环己烯性能的影响,并采用N2物理吸附、透射电镜、X射线衍射、X射线荧光、傅里叶变换红外和程序升温还原等手段对催化剂进行了表征.结果表明,二乙醇胺可以与浆液中ZnSO4反应生成(Zn(OH)2)3(ZnSO4)(H2O)3和硫酸二乙醇胺盐.随着二乙醇胺用量的增加,化学吸附在催化剂表面的(Zn(OH)2)3(ZnSO4)(H2O)3增多,它与硫酸二乙醇胺盐的协同作用提高了Ru-Zn(4.9%)催化剂上苯选择加氢生成环己烯的选择性.当二乙醇胺用量为0.3g时,(Zn(OH)2)3(ZnSO4)(H2O)3在Ru-Zn(4.9%)催化剂加氢后样品的表面高度分散,反应性能最佳,循环使用第3次时苯转化率为84.3%,环己烯选择性和收率分别达75.5%和63.6%;使用至第4次时,反应25min时苯转化率和环己烯选择性仍可达75%以上,环己烯收率为58%以上.     

助剂Fe和反应修饰剂修饰的Ru催化剂上苯选择加氢制环己烯

共沉淀法制备了Ru-Fe(x)催化剂,并利用X射线衍射(XRD)、X射线荧光光谱(XRF)、N2物理吸附和透射电镜等手段对催化剂进行了表征.结果表明,Ru-Fe(x)催化剂中助剂Fe以Fe3O4形式存在.单独Fe3O4并不能提高Ru催化剂的环己烯选择性.但在加氢过程中Fe3O4可与反应修饰剂ZnSO4反应生成(Zn(OH)2)3(ZnSO4)(H2O)x(x=1 or 3).化学吸附的(Zn(OH)2)3(ZnSO4)(H2O)x(x=1 or 3)在提高Ru催化剂环己烯选择性中起着关键作用.此外,Ru-Fe(x)催化剂的性能还与浆液中的Zn2+浓度和pH值有关.在0.61 mol/L ZnSO4溶液中Ru-Fe(0.47)催化剂不但给出了56.7%的环己烯收率,而且具有良好的稳定性和重复使用性能.化学吸附在Ru表面的Fe2+同样能提高Ru催化剂的环己烯选择性.在0.29 mol/L和0.61 mol/L FeSO4溶液中Ru-Fe(0.47)催化剂上化学吸附Fe2+量近似,性能近似.因为Fe2+和Zn2+性质的差异,在0.29 mol/L和0.61 mol/L FeSO4溶液中Ru-Fe(0.47)催化剂的环己烯选择性分别低于在同浓度的ZnSO4溶液中的.     

高活性高选择性苯部分加氢制环己烯催化剂的研究

用化学还原法制得了高活性高选择性Ru-Zn-B/ZrO2苯部分加氢催化剂体系.催化剂制备中活性组分前驱体RuCl3宜在ZrO2上吸附后再还原.催化剂的活性指数γ40和SHE分别为154.7%和85.5%,均高于进口催化剂水平γ40和SHE分别为100%～120%和75%～80%,具有很好的应用前景.催化剂中Ru-Zn-B为三元非晶合金,B以元素态和NaBO3*3H2O化合物存在.随反应温度提高,合金分解,Ru晶化.反应浆液中加入ZnSO4*7H2O可有效降低活性,提高环己烯的选择性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.