助剂镍/钴对磷化钨催化剂加氢精制性能的影响

在共浸渍法制备磷化钨／γ-Al2O3催化剂基础上，分别加人1％、3％、5％、7％和9％(占活性组分比例)的助剂镍或钴，制得负载30％含助剂镍／钴磷化钨／γ-Al2O3系列催化剂，考察了助剂及其加人比例对催化剂加氢脱硫和加氢脱氮性能的影响．结果表明，加人适当比例的助剂镍或钴，有利于提高磷化钨／γ-Al2O3催化剂的加氢脱硫活性，当助剂含量分别为5％镍或7％钴时，催化剂的噻吩加氢脱硫率最高；助剂镍对磷化钨／γ-Al2O3催化剂的加氢脱氮反应不利，而加人适当比例助剂钴有利于提高催化剂加氢脱氮活性，当助剂钴含量为5％时，催化剂吡啶加氢脱氮率最高．温度对磷化钨／γ-Al2O3催化剂加氢精制性能有一定影响，高温有利于加氢脱硫反应，低温有利于加氢脱氮反应．     

噻吩在不同负载磷化钨催化剂上的加氢脱硫

采用程序升温和高纯氢气还原无定型磷钨酸盐与载体γ-Al2O3机械混合物的方法，制备了活性组分为磷化钨、负载量分别为20％、25％、30％和35％的新型磷化钨催化剂，并对其噻吩加氢脱硫反应活性进行考察。实验结果表明，负载磷化钨催化剂的噻吩加氢脱硫率明显高于非负载磷化钨催化剂；不同负载磷化钨催化剂还原反应均为放热反应，且发生还原反应生成活性组分磷化钨的最低温度大于610℃，对于噻吩加氢脱硫反应，WP1活性较高，WP4活性较低，在340℃时分别为85．23％和67．93％，催化剂WP1具有较好的稳定性。     

负载β-Mo2N0.78催化剂上加氢脱硫和加氢脱氮反应行为的研究

在N2-H2下，利用程序升温还原氮化反应制备氧化铝负载的β-Mo2N0.78催化剂，并以苯并噻吩（BT）、二苯并噻吩(DBT)和喹啉为模型化合物，考察该催化剂的加氢脱硫、加氢脱氮活性和选择性。实验结果表明，升高反应温度和压力均提高催化剂的加氢脱硫、加氢脱氮活性；升高温度可同时改善DBT的直接脱硫和氢化脱硫，对选择性没有明显的影响；提高反应压力有利于加氢产物的生成；同时可以使联苯加氢转化为环己基苯。添加喹啉的加氢脱硫反应结果表明，含氮化合物的添加降低了催化剂加氢脱硫反应活性，抑制了氢化脱硫反应的发生。少量硫化合物的添加，使喹啉的转化率提高，还提高了脱氮率。     

渣油加氢处理过程中Mo-V/Al_2O_3的催化性能及协同效应

采用孔饱和浸渍法制备了不同Mo/(Mo+V)原子比的Mo-V/Al2O3催化剂,运用拉曼光谱、H2程序升温还原和高分辨透射电镜对催化剂进行了表征,同时以萘为模型化合物,考察了催化剂的加氢活性;以科威特常渣为原料,考察了其加氢脱金属和脱硫活性.结果表明,在上述反应中,Mo与V具有协同作用.由于渣油中金属和硫的存在形态不同,并且V-Mo-S相和V-S相对于渣油加氢脱金属反应的催化作用要大于渣油加氢脱硫反应,因此与Ni-Mo/Al2O3催化剂相比,Mo-V/Al2O3催化剂的脱金属活性较高,而脱硫活性较低.     

NiW/Al_2O_3催化剂酸性与加氢活性的调变及对重油加氢脱氮性能的影响

以Ni、W为催化剂的活性金属组分,采用等体积浸渍法制备了NiW/Al2O3加氢脱氮催化剂,考察了Al2O3载体表面经硼酸修饰后对催化剂酸性的影响,以及活性金属与柠檬酸络合后对催化剂加氢反应性能的影响。NH3-TPD、HRTEM、H2-TPR、XPS等表征结果表明,Al2O3载体表面硼酸修饰增加了催化剂表面的中强酸量,减少了强酸量,且削弱了金属与载体之间的强相互作用,但活性中心数目减少。金属与柠檬酸络合可以减小活性相晶粒长度、提高活性相分散性及硫化程度。催化剂的反应评价结果表明,硼酸修饰与柠檬酸络合共同作用可以增强催化剂的重油加氢处理能力,促进芳环与胶质的加氢饱和;具有适宜的氢解与加氢活性,兼顾碱性氮与非碱性氮的脱除,体现了催化剂良好的重油加氢脱氮性能。     

TiO_2-Al_2O_3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO2-Al2O3复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备.通过N2吸附(BET)、X射线衍射(XRD)、透射电镜(TEM)、程序升温还原(TPR),X射线光电子能谱(XPS)和等离子体发射光谱(ICP-AES)表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能.结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al2O3的孔特征,具有较大的比表面积和较宽的孔分布,TiO2主要以表面富集的形式分散在管状的γ-Al2O3表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni2P和Ni12P5;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO2趋于在块状的Al2O3表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni2P.不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n(Ti)/n(Al)=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340℃,3 MPa,氢油体积比500,液时空速3 h-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

载体性质对Pd催化剂加氢脱硫性能的影响

以Si O2、全硅MCM-41(Si-MCM-41)、通过机械混合Si-MCM-41与ZSM-5得到的Z-MCM-41-M以及通过在ZSM-5外部包覆MCM-41制备得到的Z-MCM-41四种材料为载体,制备了四种负载型Pd催化剂。采用XRD、HRTEM、N2吸附-脱附、NH3-TPD手段对Pd催化剂进行了表征;以二苯并噻吩(DBT)为模型化合物,在固定床反应器上对四种催化剂的加氢脱硫(HDS)活性、加氢路径选择性和加氢裂化活性进行了考察,研究了不同类型载体对Pd催化剂加氢脱硫性能的影响。结果表明,载体的性质会显著影响负载型Pd催化剂的加氢脱硫性能。载体的比表面积对负载型Pd催化剂加氢脱硫活性影响不大,但是HYD路径的选择性与载体的孔道结构有关;具有介孔孔道结构有利于加氢路径选择性的提高。酸性载体负载的Pd催化剂表现出较好加氢脱硫活性和加氢选择性,这与氢溢流有关。介孔材料的孔道结构与微孔沸石的酸性有机结合,所得到的Z-M CM-41复合材料是是潜在的贵金属Pd加氢脱硫催化剂优良载体,可有效提升其加氢脱硫活性。     

Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

WP/γ-Al2O3催化剂负载方式对噻吩加氢脱硫性能的影响

以γ-Al2O3为载体，分别采用机械混合法、共浸渍法、分步浸渍法和程序升温、高纯氢气还原无定型磷钨酸盐的方法，制备了活性组分为磷化钨，负载量为20%的WP/γ-Al2O3催化剂。考察了不同方法制备的催化剂对噻吩加氢脱硫（HDS）反应的催化活性。结果表明：不同负载方式对催化剂结构有一定影响，对噻吩加氢脱硫性能的影响在低温时较明显。采用机械混合方式，先混合后还原方法制备的催化剂其HDS活性比先还原后混合方法制备的催化剂高；采用共浸渍和分步浸渍方式，通过焙烧所形成的催化剂其HDS活性分别比不经焙烧所形成的催化剂高或接近；浸渍焙烧所形成的催化剂其HDS活性远远高于机械混合法制备的催化剂。     

TiO2-Al2O3载体的制备及Ni2P/TiO2-Al2O3催化剂上的同时加氢脱硫和加氢脱氮反应

 以溶胶-凝胶法制备的 TiO2-Al2O3 复合氧化物为载体, 采用浸渍法制备了 Ni2P/TiO2-Al2O3 催化剂, 并用 X 射线衍射、N2 吸附脱附、红外和 X 射线光电子能谱等技术对催化剂进行了表征, 考察了载体中 TiO2 含量、焙烧温度及其制备方法对 Ni2P/TiO2-Al2O3 催化剂上同时进行噻吩加氢脱硫和吡啶加氢脱氮反应的影响. 结果表明, 以 Ni/P 摩尔比为 1/2 的前驱体制备的催化剂表面仅出现 Ni2P 物相; 当载体中 TiO2 的含量为 80%, 焙烧温度为 550 oC 时, Ni2P/TiO2-Al2O3 催化剂上加氢脱硫和加氢脱氮的活性最高. 在 360 oC, 3.0 MPa, 氢/油体积比 500, 液时体积空速 2.0 h?1 的条件下, 噻吩和吡啶转化率分别为 61.3%和 64.4%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.