非负载型磷化钼加氢精制催化剂的研制

 尽管有相当多的文献和专利报道了含磷加氢精制催化剂的研究及磷的加入对Mn-Ni、Ni-Mo、Ni-W、Co-Mo、Mo、W、Ni、Co等各类加氢精制催化剂结构、及HDS、HDN活性的影响，并证明了磷或含磷化合物可作为加氢精制催化剂的助剂和稳定剂，但对于磷化物加氢催化剂的合成及对其HDS、HDN活性的研究还很少。本文在较低温度下用氢气直接还原磷钼酸铵盐得到非负载型的磷化钼催化剂，并以制备的磷化钼为活性组分，以SiC和γ-Al2O3为稀释剂，选择高浓度和低浓度的吡啶、噻吩和环己烯的混合物为模型化合物，以环己烷作溶剂，测定了制备催化剂的HDS、HDN及HYD活性。结果表明，所研制的非负载型磷化钼加氢精制催化剂对两种含有吡啶、噻吩和环己烯的模型化合物具有同时HDN, HDS 和 HYD的性能。     

制备条件对磷化钼加氢脱硫催化活性的影响

采用程序升温还原方法制得磷化钼(MoP)催化剂,在常压连续微型化反应装置中,以噻吩为模型化合物,对催化剂的加氢脱硫活性进行评价。考察了还原温度、磷钼摩尔比、不同磷源等制备条件对MoP催化活性的影响。实验结果表明,在MoP生成温度区间内,随着还原温度的升高,催化剂活性降低;磷钼摩尔比为1∶1时,噻吩转化率最高,而磷钼摩尔比为1∶2和2∶1时制备催化剂的催化活性相当;采用磷酸二氢铵、磷酸铵以及磷酸为磷源,均可制得磷化钼,而以磷酸二氢铵为磷源时制备磷化钼催化剂的活性最佳。在噻吩加氢脱硫反应条件下反应后,不同磷源制备的磷化钼整体物相均没有发生变化。     

一种新型的磷化钼加氢精制催化剂的研究

通过(NH4)Mo7O24·4H2O和(NH4)2HPO4水溶液沉淀、焙烧在923K用H2还原制得磷化钼催化剂.XRD检测表明,用H2还原后有纯的磷化钼生成.在3.0MPa的高压连续微反系统中测定催化剂的加氢活性.以制备的磷化钼为活性组分、γ-Al2O3为稀释剂,考察了空速、反应温度和反应时间对模型化合物的HDN、HDS和HDY性能的影响,结果表明:在合适的条件下,其脱硫脱氮率可达到90%以上.模型化合物为吡啶、噻吩和环己烯,吡啶含量以N计(为0.2%)、噻吩含量以S计(为0.3%),环己烯含量为20%,以环己烷作溶剂.     

磷化过程对MoP催化剂醋酸加氢合成乙醇性能的影响

制备了系列磷化钼催化剂用于醋酸加氢合成乙醇活性评价,并采用XRD、XPS和SEM等技术对催化剂进行表征。结果表明,催化剂除含有MoP外,还有MoP_2O_7和MoO_2等物种,催化醋酸生成乙醇的活性物种是MoP,或者是MoP与MoP_2O_7、MoO_2协同起催化作用。磷化温度一定程度上影响催化剂的形成和活性组分的分布,磷化温度太低,MoP形成量少,磷化温度太高,MoP发生团聚和烧结,磷化温度为650℃时制备的催化剂活性最高。磷钼物质的量比为1.0时催化剂的乙醇合成性能最高。     

溶胶-凝胶法制备MoP/SiO2催化剂加氢脱硫催化活性的研究

以正硅酸乙酯为硅源,以钼酸铵和磷酸二氢铵为钼源和磷源,采用溶胶-凝胶法,经干燥、焙烧,程序升温还原制备得到二氧化硅负载磷化钼(MoP)催化剂。以噻吩、二苯并噻吩为模型化合物,对负载催化剂的加氢脱硫活性进行评价,考察了负载量、反应压力、反应温度等因素对催化活性的影响。实验结果表明,MoP/SiO₂催化剂Mo的最佳负载量为20%,升高反应压力和温度均有利于提高二苯并噻吩的转化率,但降低了产物中联苯的含量。     

NiMoS/γ-Al2O3上二苯并噻吩加氢脱硫和喹啉加氢脱氮反应的相互影响

在固定床高压微反装置上,考察了预硫化型NiMoS/γ-Al2O3催化剂上二苯并噻吩(DBT)加氢脱硫(HDS)反应和喹啉加氢脱氮(HDN)反应之间的相互影响.结果表明,喹啉对DBT的HDS反应具有强烈的抑制作用,其中对加氢路径比氢解路径的抑制作用更强,这是由喹啉及其HDN反应的中间产物与DBT在活性位上的竞争吸附造成的.在300和340℃时,喹啉对DBT的HDS反应中氢解路径的抑制程度与其HDN中间产物的相对含量紧密相关.而DBT能够提高喹啉的脱氮能力,这源于其HDS产物H2S.H2S促进了催化剂表面硫阴离子空穴向B酸位的转化,从而提高了喹啉HDN中间产物分子的C(sp3)-N键的断裂能力.HDN活性相的保持不需要过多的硫原子.     

碳化钼催化剂加氢脱氮性能研究

MoO3在CH4/H2气氛中程序升温还原碳化反应制备了Mo2C催化剂,用XRD、BET、SEM、XPS进行了表征。以吡啶/环己烷溶液为模型化合物,在高压微反装置上评价了碳化钼催化剂的吡啶加氢脱氮性能。结果表明,MoO3在CH4/H2气氛中程序升温至675℃可制得高纯度的β-Mo2C,SEM表征其形貌为板块状颗粒,平均粒径约3.9μm,比表面积达到了10.7m2/g,高于其前驱体MoO3 的2.7倍。在反应压力3.0MPa,空速为8h－1,H2/原料液体积比为500∶1,体积分数为5%的吡啶/环己烷溶液中,碳化钼催化剂在340℃下的吡啶加氢脱氮转化率达到了86.30%,高于相应MoS2约8%。随还原碳化温度的升高,碳化钼催化剂的比表面积降低,表面积炭增多,导致其吡啶加氢脱氮活性下降。确定的碳化钼催化剂的合成条件以还原碳化温度675℃、还原碳化气体空速1.8×104h－1左右较为适宜。     

Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

还原温度对低温还原法制备的Ni_2P/Ti-MCM-41催化剂加氢脱硫性能的影响

以氯化镍(Ni Cl_2·6H_2O)为镍源、次磷酸铵(NH_4H_2PO_2)为磷源、Ti-MCM-41为载体,通过程序升温还原法制备了Ni_2P/Ti-M CM-41催化剂,并采用H_2-TPR、XRD、BET、XPS、TEM等手段对其结构和性质进行了表征。以二苯并噻吩(DBT)为模型化合物,考察了还原温度对Ni_2P/Ti-M CM-41催化剂的加氢脱硫(HDS)性能的影响。结果表明,程序升温还原法制备的Ni_2P/Ti-M CM-41催化剂前驱体的还原温度为318℃,比传统程序升温还原制备的Ni_2P低200℃。在350-500℃下还原得到的催化剂活性相为单一的Ni_2P相,较低的还原温度有利于形成更小粒径的磷化镍晶粒。还原温度为400℃时,制得的Ni_2P/Ti-M CM-41催化剂比表面积高、分散性最好、表面P富集少,具有最高的HDS活性;在340℃、3.0 M Pa、H_2/油体积比500、质量空速(WHSV)为2.0 h~(-1)的条件下,二苯并噻吩HDS转化率达到99.4%。     

WP/γ-Al2O3催化剂负载方式对噻吩加氢脱硫性能的影响

以γ-Al2O3为载体，分别采用机械混合法、共浸渍法、分步浸渍法和程序升温、高纯氢气还原无定型磷钨酸盐的方法，制备了活性组分为磷化钨，负载量为20%的WP/γ-Al2O3催化剂。考察了不同方法制备的催化剂对噻吩加氢脱硫（HDS）反应的催化活性。结果表明：不同负载方式对催化剂结构有一定影响，对噻吩加氢脱硫性能的影响在低温时较明显。采用机械混合方式，先混合后还原方法制备的催化剂其HDS活性比先还原后混合方法制备的催化剂高；采用共浸渍和分步浸渍方式，通过焙烧所形成的催化剂其HDS活性分别比不经焙烧所形成的催化剂高或接近；浸渍焙烧所形成的催化剂其HDS活性远远高于机械混合法制备的催化剂。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.