Fabrication and Characterization of Mg-Doped GaN Nanowires

Mg-doped GaN nanowires have been synthesized by ammoniating Ga2O3 films doped with Mg under flowing ammonia atmosphere at 850℃. The Mg-doped GaN nanowires are characterized by x-ray diffraction （XRD）, scanning electron microscope （SEM）, high-resolution transmission electron microscopy （HRTEM） and photoluminescence （PL）. The results demonstrate that the nanowires are single crystalline with hexagonal wurzite structure. The diameters of the nanowires are 20-30nto and the lengths are 50-100μm. The GaN nanowires show three emission bands with well-defined PL peak at 3.45 eV, 3.26 eV, 2.95 eV, respectively. The large distinct blueshift of the bandgap emission can be attributed to the Burstein-Moss effect. The peak at 3.26 eV represents the transition from the conduction-band edge to the acceptor level AM （acceptor Mg）. The growth mechanism of crystalline GaN nanowires is discussed briefly.     

Photoluminescence Characterization of Nanocrystalline ZnO Array

High-density and uniform well-aligned ZnO sub-micron rods are synthesized on the silicon substrate over a large area. The morphology and structure of the ZnO sub-micron rods are investigated by x-ray diffraction, transmission electron microscopy and Raman spectra. It is found that the ZnO sub-micron rods are of high crystal quality with the diameter in the range of 400-600 nm and the length of several micrometres long. The optical properties were studied by photoluminescence spectra. The results show that the intensity of the ultraviolet emission at 3.3eV is rather high, meanwhile the deep level transition centred at about 2.38eV is weak. The free exciton emission could a/so be observed at low temperature, which implies the high optical quality of the ZnO sub-micron rods.This growth technique provides one effective way to fabricate the high crystal quality ZnO nanowires array, which is very important for potential applications in the new-type optoelectronic nanodevices.     

Flexible electrically pumped random lasing from ZnO nanowires based on metal–insulator–semiconductor structure

Flexible electrically pumped random laser(RL) based on ZnO nanowires is demonstrated for the first time to our knowledge. The ZnO nanowires each with a length of 5 μm and an average diameter of 180 nm are synthesized on flexible substrate(ITO/PET) by a simple hydrothermal method. No obvious visible defect-related-emission band is observed in the photoluminescence(PL) spectrum, indicating that the ZnO nanowires grown on the flexible ITO/PET substrate have few defects. In order to achieve electrically pumped random lasing with a lower threshold, the metal–insulator–semiconductor(MIS) structure of Au/SiO_2/ZnO on ITO/PET substrate is fabricated by low temperature process. With sufficient forward bias, the as-fabricated flexible device exhibits random lasing, and a low threshold current of ～ 11.5 m A and high luminous intensity are obtained from the ZnO-based random laser. It is believed that this work offers a case study for developing the flexible electrically pumped random lasing from ZnO nanowires.     

Abnormal Photoluminescence Properties of Polycrystalline ZnO Nanowire Arrays Synthesized by Electrodeposition

Large-scale ZnO nanowire arrays are synthesized by electrodeposition with subsequent heat treatment in atmosphere ambient at 450-650℃. Photoluminescence （PL） is investigated at 295K. Abnormal PL properties of an unusual sharp emission at 485 nm and a broad ultraviolet emission which are different from the other works of ZnO PL before are observed. Field emission scanning electronic microscopy and transmission electron microscopy results show that the length of Zn 0 nanowires is nearly 5μm and their diameter is about 70 nm. X-ray diffraction and electron diffraction results reveal that the ZnO nanowires are a polycrystalline structure.     

Synthesis and electrical properties of In2O3(ZnO)m superlattice nanobelt

One-dimensional（ID） In₂O₃（ZnO）_m superlattice nanobelts are synthesized by a chemical vapor deposition method.The formation of the In₂O₃（ZnO）_m superlattice is verified by the high-resolution transmission electron microscopy images.The typical zigzag boundaries could be clearly observed.An additional peak at 614 cm^-1 is found in the Raman spectrum,which may correspond to the superlattice structure.The study about the electrical transport properties reveals that the In₂O₃（ZnO）_m nanobelts exhibit peculiar nonlinear I-V characteristics even under the Ohmic contact measurement condition,which are different from the Ohmic behaviors of the In-doped ZnO nanobelts.The photoelectrical measurements show the differences in the photocurrent property between them,and their transport mechanisms are also discussed.     

Synthesis and photoluminescence study on ZnO nano-particles

A new technique, namely low pressure sputtering, has been developed to fabricate Zn nanoparticles, with a subsequent oxidation to synthesize ZnO nanoparticles in the ambient atmosphere at 500$\,^{\circ}$C. The synthesized ZnO nanoparticle has a size of 6--8~nm with a preferred orientation of $c$-axis. The produced ZnO nanoparticles have a good UV photoluminescence (PL) emission energy of 3.349 eV with a significant enhancement of donor--acceptor pair emission located at 3.305 eV which implies a number of donor and acceptor bounded excitons existing in the synthesized ZnO nano particles. The near band edge PL emission of the fabricated ZnO is dominated by the bounded excitons at 10~K.     

Enhancing UV photosensitivity of a ZnO UV nanosensor using electrical stimulation at megahertz frequency

We report a novel technique to enhance the ultraviolet (UV) photosensitivity of a ZnO nanosensor with ZnO nanowires bridged on micromachined metallic electrodes. The experimental results reveal that the photoconductivity and the time response of the ZnO nanowire sensor with either Schottky or Ohmic contacts are significantly improved by electrifying the nanowire sensors using an alternating current at the frequency of megahertz. An integrated UV sensor incorporating ZnO nanowires with a constant current mode driving circuit is developed, which demonstrates promising sensitivity and time response to UV illumination with a low power consumption.     

Detection of Fe 3d electronic states in the valence band and magnetic properties of Fe-doped ZnO film

Fe-doped ZnO film has been grown by laser molecular beam epitaxy(L-MBE) and structurally characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM),all of which reveal the high quality of the film.No secondary phase was detected.Resonant photoemission spectroscopy(RPES) with photon energies around the Fe 2p-3d absorption edge is performed to detect the electronic structure in the valence band.A strong resonant effect at a photon energy of 710 eV is observed.Fe3+ is the only valence state of Fe ions in the film and the Fe 3d electronic states are concentrated at binding energies of about 3.8 eV and 7 eV～8 eV.There are no electronic states related to Fe near the Fermi level.Magnetic measurements reveal a typical superparamagnetic property at room temperature.The absence of electronic states related to Fe near the Fermi level and the high quality of the film,with few defects,provide little support to ferromagnetism.     

Synthesis and room-temperature NO_2 gas sensing properties of a WO_3 nanowires/porous silicon hybrid structure

We report on the fabrication and performance of a room-temperature NO2 gas sensor based on a WO3 nanowires/porous silicon hybrid structure. The W18O49 nanowires are synthesized directly from a sputtered tungsten film on a porous silicon （PS） layer under heating in an argon atmosphere. After a carefully controlled annealing treatment, WO3 nanowires are obtained on the PS layer without losing the morphology. The morphology, phase structure, and crystallinity of the nanowires are investigated by using field emission scanning electron microscopy （FESEM）, X-ray diffractometer （XRD）, and high-resolution transmission electron microscopy （HRTEM）. Comparative gas sensing results indicate that the sensor based on the WO3 nanowires exhibits a much higher sensitivity than that based on the PS and pure WO3 nanowires in detecting NO2 gas at room temperature. The mechanism of the WO3 nanowires/PS hybrid structure in the NO2 sensing is explained in detail.     

Electrical characteristics and optoelectronic properties of metal--semiconductor--metal structure with zinc oxide nanowires across Au electrodes

This paper reports on a method of assembling semiconducting ZnO nanowires onto a pair of Au electrodes to construct a metal--semiconductor metal （MSM） structure by dieleetrophoresis and studying on its electrical characteristics by using current-voltage （Ⅰ - Ⅴ） measurements. An electronic model with two back to back Sehottky diodes in series with a semiconductor of nanowires was established to study the electrical transport of the MSM structures. By fitting the measured Ⅰ - Ⅴ characteristics using the proposed model, the parameters of the Schottky contacts and the resistance of nanowires could be acquired. The photoelectric properties of the MSM structures were also investigated by analysing the measurements of the electrical transports under various light intensities. The deduced results demonstrate that ZnO nanowires and their Schottky contacts with Au electrodes both contribute to photosensitivity and the MSM structures with ZnO nanowires are potentially applicable for photonic devices.     

Bi2Te3/Sb超晶格纳米线的外延生长和热电测量

通过脉冲电沉积,外延生长出小单元长度的Bi₂Te₃/Sb超晶格纳米线.借助哈曼方法,测量了超晶格纳米线阵列的热电性能,330 K时的ZT值可达0.15.研究了Bi₂Te₃/Sb超晶格纳米线阵列器件的制冷或者加热能力,发现器件的上下表面的最大温差可以达到6.6 K.     

WnNim(n+m=8)团簇结构与电子性质的理论研究

采用密度泛函理论(DFT)中的B3LYP方法,在Lanl2dz基组水平上对W_nNi_m(n+m=8)团簇的各种可能构型进行了几何参数全优化,得到了它们的基态构型;并对基态构型的平均结合能、Wiberg键级(WBI)、磁学性质、NBO进行了分析,结果表明:团簇随着W原子数的增多,稳定性增强,n≥5时,结构中都含有纯钨团簇的结构基元;W-W键级高于W-Ni键和Ni-Ni键;W₅Ni₃,W₆Ni₂团簇发生了"磁矩猝灭"的现象;在W,Ni原子内部,轨道电荷发生了转移,产生了"轨道杂化"现象,W,Ni原子之间也发生了电荷转移形成了较强的化学键. 关键词： nNi_m(n+m=8)团簇')" href="#">W_nNi_m(n+m=8)团簇 几何结构 电子性质 密度泛函理论     

过渡族元素掺杂BaTiO3-Tb1-xDyxFe2-y层状复合材料中的磁电效应

用溶胶-凝胶法制备1.0%mol Mn,Cr,Co掺杂 BaTiO₃(BTO)粉体,在1350℃下烧结成多晶陶瓷样品.X射线衍射和差示扫描量热分析表明,室温下掺杂BaTiO₃具有四方钙钛矿结构;居里点和相变潜热随Cr,Mn,Co掺杂逐渐降低.将掺杂BaTiO₃与Tb_1-xDy_xFe_2-y(TDF)胶合制成双层磁电复合材料,并研究了Cr:BTO-TDF,Mn∶BTO-TDF,Co:BTO-TDF层状复合材料中的磁电效应.实验表明,在340×80 A·m^-1偏置磁场下, Cr:BTO-TDF的横向磁电电压系数达到最大值586 mV·cm^-1·(80 A·m^-1)^-1.在400×80 A·m^-1偏置磁场下,Mn∶BTO-TDF和Co:BTO-TDF的横向磁电电压系数的最大值分别为480 mV·cm^-1·(80 A·m^-1)^-1和445mV·cm^-1·(80 A·m^-1)^-1.研究表明掺杂BaTiO₃-TDF层状复合材料中具有较强的磁电耦合.作为无铅压电材料,掺杂BaTiO₃制备的磁电效应器件颇具应用前景. 关键词： 磁电效应 双层复合材料 3')" href="#">掺杂BaTiO₃ 1-xDy_xFe_2-y')" href="#">Tb_1-xDy_xFe_2-y     

Synthesis,structural and ellipsometric evaluation of oxygen-deficient and nearly stoichiometric zinc oxide and indium oxide nanowires/nanoparticles

Oxygen-deficient (OD) and nearly stoichiometric (NST) ZnO and In₂O₃ nanowires/nanoparticles were synthesized by chemical vapor deposition on Au-coated silicon substrates. The OD ZnO and OD In₂O₃ nanowires were synthesized at 750 and 950°C, respectively, using Ar flow at ambient pressure. A mixture of flowing Ar and O₂ was used for synthesizing NST ZnO nanowires and NST In₂O₃ nanoparticles. Growth of OD ZnO nanowires and NST In₂O₃ nanoparticles was found to be via a vapor–solid (VS) mechanism and the growth of NST ZnO nanowires was via a vapor–liquid–solid mechanism (VLS). However, it was uncertain whether the growth of OD In₂O₃ nanowires was via a VS or VLS mechanism. The optical constants, thickness and surface roughness of the prepared nanostructured films were determined by spectroscopic ellipsometry measurements. A three-layered model was used to fit the calculated data to the experimental ellipsometric spectra. The refractive index of OD ZnO, NST ZnO nanowires and NST In₂O₃ nanoparticles films displayed normal dispersion behavior. The calculated optical band gap values for OD ZnO, NST ZnO, OD In₂O₃ nanowires and NST In₂O₃ nanoparticles films were 3.03, 3.55, 2.81 and 3.52?eV, respectively.     

不同气氛下SiOx纳米线的制备及形貌、红外、光致发光研究

以N₂/H₂、N₂或NH₃为载气,利用碳辅助化学气相沉积法,常压1140℃下在石英衬底上制备了大量直径为20—300 nm,长数百微米的非晶SiO_x纳米线.制备得到的纳米线具有高度定向生长的特性.利用透射电子显微镜、扫描电子显微镜及电子能谱对SiO_x纳米线的形貌及组分进行了分析,Si与O原子之比为1∶18.傅里叶红外吸收谱显示了非晶氧化硅的三个特征峰（482,806和1095 cm^-1）及1132 cm^-1无序氧化硅结构的强吸收峰.SiO_x纳米线光致发光光谱（PL）在440 nm（283 eV）处具有较强的荧光峰;N₂为载气生长的SiO_x纳米线的PL峰强比NH₃为载气生长的SiO_x纳米线峰强大四个数量级. 关键词： x纳米线')" href="#">SiO_x纳米线 碳辅助化学气相沉积法 傅里叶红外吸收 光致发光     

Probing of local ferroelectricity in BiFeO3 thin films and (BiFeO3)m(SrTiO3)m superlattices

Ferroelectric BiFeO₃ thin films and artificial superlattices of (BiFeO₃)_m(SrTiO₃)_m (m∼1-10 unit cells) were fabricated on (0 0 1)-oriented SrTiO₃ substrates by pulsed laser ablation. The variation of leakage current and macroscopic polarization with periodicity was studied. Piezo force microscopy studies revealed the presence of large ferroelectric domains in the case of BiFeO₃ thin films while a size reduction in ferroelectric domains was observed in the case of superlattice structures. The results show that the modification of ferroelectric domains through superlattice could provide an additional control on engineering the domain wall mediated functional properties.     

Synthesis and magnetic properties of Fe100-xMox alloy nanowire arrays

The Fe100-xMox(13≤x≤25) alloy nanowire arrays are synthesized by electrodeposition of Fe 2+ and Mo 2+ with different ionic ratios into the anodic aluminum oxide templates.The crystals of Fe100-xMox alloy nanowires gradually change from polycrystalline phase to amorphous phase with the increase of the Mo content and the nanowires are of amorphous structure when the Mo content reaches 25 at%,which are revealed by the X-ray diffraction and the selected area electron diffraction patterns.As the Mo content increases,the magnetic hysteresis loops of Fe100-xMox alloy nanowires in parallel to the nanowire axis are not rectangular and the slopes of magnetic hysteresis loops increase.Those results indicate that the magnetostatic interactions between nanowires and the magnetocrystalline anisotropy both have significant influences on the magnetization reversal process of the nanowire arrays.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

(HMgN3)n(n=1–5)团簇结构与性质的密度泛函理论研究

利用密度泛函理论在B3LYP/6-311G^*水平上对叠氮化合物(HMgN₃)_n(n=1–5)团簇各种可能构型进行了几何优化,预测了各团簇的最稳定结构. 并对最稳定结构的成键特性、电荷分布、振动特性及稳定性进行理论研究. 结果表明:HMgN₃团簇最稳定结构为直线型;(HMgN₃)_n(n=2,5)团簇最稳定结构为叠氮基中N原子和金属原子相连构成Mg–N–Mg结构;(HMgN₃)_n(n=3,4)团簇最稳定结构为叠氮基与Mg原子相互链接形成的环状结构. 团簇最稳定结构中金属Mg原子均显示正电性,H原子均显示负电性,叠氮基中间的N原子显示正电性、两端的N原子显示负电性,且与Mg原子直接作用的N原子负电性更强. Mg–N键和Mg–H键为典型的离子键,叠氮基内N原子之间是共价键. 团簇最稳定结构的红外光谱分为三部分,其最强振动峰均位于2258–2347 cm^-1,振动模式为叠氮基中N–N键的反对称伸缩振动. 叠氮基在团簇和晶体中结构不变,始终以直线型存在. 稳定性分析显示,(HMgN₃)₃团簇相对于其他团簇更为稳定. 关键词： 3)_n(n=1–5)团簇')" href="#">(HMgN₃)_n(n=1–5)团簇 叠氮基 密度泛函理论 结构与性质